General Information Gates/Rohloff - Koga Signature
General Information Gates/Rohloff - Koga Signature General Information Gates/Rohloff - Koga Signature
2 mounting • Mounting the Gates Carbon Drive Belt • Checking the belt tension • Checking the belt tension using the Tension Tester • Checking the belt tension without the Tension Tester • Using the Snubber to keep the Gates Carbon Drive Belt from ratcheting • Snubber assembly • Mounting the Snubber • Removing the Snubbers • Mounting the Gates Carbon Drive Front Sprocket • Mounting the Front Sprocket at the crank adapter • Mounting the Gates Carbon Drive Hybrid Rear Sprocket M46x6 • Mounting the Rear Sprocket M46x6 to the Gates-Rohloff Carrier M46x6 • Retrofitting the rear sprocket to a Rohloff SPEEDHUB • Retrofitting the rear sprocket to a Rohloff SPEEDHUB 500/14 with chain sprocket • Removing the Rear Sprocket M46x6 with Gates-Rohloff Carrier M46x6 from Rohloff SPEEDHUB 500/14 • Removing the Gates-Rohloff Carrier from the Rohloff SPEEDHUB 500/14 • Removing the Gates-Rohloff Carrier from the rear sprocket 10
mounting Mounting the Gates Carbon Drive Belt 2 The following steps describe how to mount the belt in a bike with already mounted sprockets. If your sprockets have not been mounted yet, please follow the instructions for Mounting front and rear sprockets first. If you have any difficulties with mounting the belt, the video at www.carbondrivesystems.com will help you. 1. Open the frame break or ‘gate’ on the frame’s rear triangle. Since this break may vary from one manufacturer to another, you’ll need to follow the instructions of the manufacturer of your frame. In the following illustrations the frame is opened at the dropout. Insert the belt through the opening of the frame. 2. Hang the belt over the bottom bracket and lock the frame gate. 3. Place the belt on the rear sprocket and mount the rear wheel into the rear dropouts. www.carbondrivesystems.com 11
- Page 1 and 2: Manual for the Gates Carbon Drive S
- Page 3 and 4: 1 first steps • Congratulations!
- Page 5 and 6: first steps 1 Have your bike checke
- Page 7 and 8: first steps 1 Mounting the tensione
- Page 9: first steps 1 7. 8. 1. Drive belt n
- Page 13 and 14: mounting 2 Illustration 3: Correct
- Page 15 and 16: mounting Checking the belt tension
- Page 17 and 18: mounting Checking the belt tension
- Page 19 and 20: mounting axle. If the Snubber is lo
- Page 21 and 22: mounting 2 Shim ring for bottom bra
- Page 23 and 24: mounting Mounting the Gates Carbon
- Page 25 and 26: mounting Lubricate the inner thread
- Page 27 and 28: mounting Ensure that the surfaces o
- Page 29 and 30: mounting Removing the Gates-Rohloff
- Page 31 and 32: exchange When does the Gates Carbon
- Page 33 and 34: exchange Profile Wear Gauge Illustr
- Page 35 and 36: for Frame builders Frame requiremen
- Page 37 and 38: 5 Gear Ratio Comparisum • Compari
- Page 39 and 40: atio overview 19 Teeth rear 20 Teet
- Page 41 and 42: atio overview Sprocket-size combina
- Page 43: Find more information for Europe: U
mounting<br />
Mounting the <strong>Gates</strong> Carbon Drive Belt<br />
2<br />
The following steps describe how to mount the belt in a bike with already mounted sprockets.<br />
If your sprockets have not been mounted yet, please follow the instructions for Mounting front<br />
and rear sprockets first. If you have any difficulties with mounting the belt, the video at<br />
www.carbondrivesystems.com will help you.<br />
1. Open the frame break or ‘gate’ on the<br />
frame’s rear triangle. Since this break<br />
may vary from one manufacturer to<br />
another, you’ll need to follow the<br />
instructions of the manufacturer<br />
of your frame. In the following<br />
illustrations the frame is opened at<br />
the dropout.<br />
Insert the belt through the opening<br />
of the frame.<br />
2. Hang the belt over the bottom<br />
bracket and lock the frame gate.<br />
3. Place the belt on the rear sprocket<br />
and mount the rear wheel into the<br />
rear dropouts.<br />
www.carbondrivesystems.com<br />
11