LINEAR MOTION SOLUTIONS - Brd. Klee A/S

Sleeve Flange Bearings - PSF
Inch Series
PSF Sleeve Bearings
L
d
B
A
C
Aluminum Alloy
Frelon® Liner
Basic dimensional information
c d
MAX. STATIC
recommended Housing Bore
Nominal bearing Size
A
Bearing I.d.
B
o.d.
flange
o.d.
flange
width
L
Length
LOAD (lbs.)
FRELON
Bearing
Weight Slip Fit & Epoxy Press Fit
PART NO. I.D. 0.D. LENGTH MIN. MAX. MIN. MAX. MIN. MAX. GOLD J (oz.) MIN. MAX. MIN. MAX.
PSF0305-02 3/16" 5/16" 1/4" 0.1890 0.1900 0.3135 0.3145 0.4370 0.0625 0.230 0.250 130 65 0.023 0.3145 0.3155 0.3125 0.3130
PSF0305-04 3/16" 5/16" 1/2" 0.1890 0.1900 0.3135 0.3145 0.4370 0.0625 0.480 0.500 272 136 0.044 0.3145 0.3155 0.3125 0.3130
PSF0406-02 1/4" 3/8" 1/4" 0.2515 0.2525 0.3760 0.3770 0.5000 0.0625 0.230 0.250 174 87 0.031 0.3770 0.3780 0.3750 0.3755
PSF0406-03 1/4" 3/8" 3/8" 0.2515 0.2525 0.3760 0.3770 0.5000 0.0625 0.355 0.375 268 134 0.044 0.3770 0.3780 0.3750 0.3755
PSF0406-04 1/4" 3/8" 1/2" 0.2515 0.2525 0.3760 0.3770 0.5000 0.0625 0.480 0.500 362 181 0.055 0.3770 0.3780 0.3750 0.3755
PSF0610-04 3/8" 5/8" 1/2" 0.3765 0.3775 0.6260 0.6270 0.8750 0.1250 0.480 0.500 542 271 0.20 0.6270 0.6280 0.6250 0.6255
PSF0610-06 3/8" 5/8" 3/4" 0.3765 0.3775 0.6260 0.6270 0.8750 0.1250 0.730 0.750 824 412 0.25 0.6270 0.6280 0.6250 0.6255
PSF0710-06 7/16" 5/8" 3/4" 0.4390 0.4400 0.6260 0.6270 0.9375 0.1250 0.730 0.750 962 481 0.20 0.6270 0.6280 0.6250 0.6255
PSF0812-04 1/2" 3/4" 1/2" 0.5015 0.5025 0.7510 0.7520 1.0000 0.1250 0.480 0.500 722 361 0.25 0.7520 0.7530 0.7500 0.7505
PSF0812-06 1/2" 3/4" 3/4" 0.5015 0.5025 0.7510 0.7520 1.0000 0.1250 0.730 0.750 1098 549 0.30 0.7520 0.7530 0.7500 0.7505
PSF0812-08 1/2" 3/4" 1" 0.5015 0.5025 0.7510 0.7520 1.0000 0.1250 0.980 1.000 1474 737 0.40 0.7520 0.7530 0.7500 0.7505
PSF1014-06 5/8" 7/8" 3/4" 0.6265 0.6275 0.8760 0.8770 1.0000 0.1250 0.730 0.750 1372 686 0.35 0.8770 0.8780 0.8750 0.8755
PSF1014-08 5/8" 7/8" 1" 0.6265 0.6275 0.8760 0.8770 1.0000 0.1250 0.980 1.000 1842 921 0.45 0.8770 0.8780 0.8750 0.8755
PSF1216-08 3/4" 1" 1" 0.7515 0.7525 1.0010 1.0020 1.2500 0.1250 0.980 1.000 2210 1105 0.55 1.0020 1.0030 0.9995 1.0000
PSF1620-12 1" 1-1/4" 1-1/2" 1.0015 1.0025 1.2510 1.2520 1.5000 0.1250 1.480 1.500 4446 2223 1.05 1.2520 1.2530 1.2490 1.2500
PSF2024-16 1-1/4" 1-1/2" 2" 1.2515 1.2525 1.5010 1.5020 1.7500 0.1250 1.980 2.000 7434 3717 1.80 1.5020 1.5030 1.4990 1.5000
PSF2428-16 1-1/2" 1-3/4" 2" 1.5015 1.5025 1.7510 1.7520 2.0000 0.1250 1.980 2.000 8918 4459 2.16 1.7520 1.7530 1.7490 1.7500
PSF2832-24 1-3/4" 2" 3" 1.7515 1.7525 2.0010 2.0020 2.2500 0.1250 2.980 3.000 15658 7829 3.30 2.0020 2.0030 1.9990 2.0000
PSF3236-24 2" 2-1/4" 3" 2.0015 2.0025 2.2510 2.2520 2.5000 0.1250 2.980 3.000 17894 8947 3.75 2.2520 2.2530 2.2490 2.2500
PSF4044-24 2-1/2" 2-3/4" 3" 2.5015 2.5025 2.7510 2.7520 3.0000 0.1250 2.980 3.000 22364 11182 4.60 2.7520 2.7530 2.7490 2.7500
PSF4852-28 3" 3-1/4" 3-1/2" 3.0015 3.0025 3.2510 3.2520 3.5000 0.1250 3.480 3.500 31336 15668 6.30 3.2520 3.2530 3.2485 3.2495
Sleeve Bearing - PSF
INSTALLATION INSTRUCTIONS
1. Slip the bearing sleeve into the housing and epoxy into
place with Loctite ® or similar type bonding agent.
CAUTION: Do NOT let any of the adhesive touch the bearing
liner. It will harden and interfere with the running clearance.
2. Freeze the bearings at 0°F (-17.75°C) for 30-45 minutes.
Using gloves, remove the bearings from the freezer and slip
them into the housing. As they heat to room temperature,
full contact between the bearing and housing will be
achieved. The greatest advantage to this technique over
traditional pressing is greater accuracy in alignment.
Ordering Information
Precision Sleeve Flange - PSF
I.D. in 1/16" Increments
O.D. in 1/16" Increments
Length in 1/8" Increments
Note: Lengths not listed above must be specially quoted.
800.962.8979 • www.pbclinear.com 155