DVP-ES2-EX2-SS2-SA2-SX2-Operation Manual

2. Programming Concepts
Special
D
Content
ES2 SS
EX2 2
SA
2
SX
2
OFF
ON
STOP
RUN
RUN
Attrib. Latch
-ed
Default
STOP
D1187 Index register F3 ○ ○ ○ ○ 0 - - R/W NO 0
D1188 Index register E4 ○ ○ ○ ○ 0 - - R/W NO 0
D1189 Index register F4 ○ ○ ○ ○ 0 - - R/W NO 0
D1190 Index register E5 ○ ○ ○ ○ 0 - - R/W NO 0
D1191 Index register F5 ○ ○ ○ ○ 0 - - R/W NO 0
D1192 Index register E6 ○ ○ ○ ○ 0 - - R/W NO 0
D1193 Index register F6 ○ ○ ○ ○ 0 - - R/W NO 0
D1194 Index register E7 ○ ○ ○ ○ 0 - - R/W NO 0
D1195 Index register F7 ○ ○ ○ ○ 0 - - R/W NO 0
D1220 Pulse output mode setting of CH0 (Y0, Y1) ○ ○ ○ ○ 0 - - R/W NO 0
D1221 Pulse output mode setting of CH1 (Y2, Y3) ○ ○ ○ ○ 0 - - R/W NO 0
D1232*
D1233*
D1234*
D1235*
Number of output pulses for CH0 (Y0, Y1) rampdown
stop when mark sensor receives signals.
(Low word).
Number of output pulses for CH0 (Y0, Y1) rampdown
stop when mark sensor receives signals.
(High word).
Number of output pulses for CH1 (Y2, Y3) rampdown
stop when mark sensor receives signals.
(Low word).
Number of output pulses for CH2 (Y2, Y3) rampdown
stop when mark sensor receives signals.
(High word).
○ ○ ○ ○ 0 0 -- R/W NO 0
○ ○ ○ ○ 0 0 -- R/W NO 0
○ ○ ○ ○ 0 0 -- R/W NO 0
○ ○ ○ ○ 0 0 -- R/W NO 0
D1240*
D1241*
D1242*
D1243*
D1244
D1245
D1249
D1250
D1252
When interupt I400/I401/I100/I101 occurs,
D1240 stores the low word of high-speed counter.
When interupt I400/I401/I100/I101 occurs,
D1241 stores the high Word of high-speed
counter.
When interupt I500/I501/I300/I301 occurs,
D1242 stores the low Wordof high-speed counter.
When interupt I500/I501/I300/I301 occurs, D1243
stores the high Word of high-speed counter.
Idle time (pulse number) setting of CH0 (Y0, Y1)
The function is disabled if set value≦0.
Idle time (pulse number) setting of CH1 (Y2, Y3)
The function is disabled if set value≦0.
Set value for COM1 (RS-232) data receiving timeout
(Unit: 1ms, min. 50ms, value smaller than
50ms will be regarded as 50ms) (only applicable
for MODRW/RS instruction) In RS instruction, no
time-out setting if “0” is specified.
COM1 (RS-232) communication error code (only
applicable for MODRW/RS instruction)
Set value for COM3 (RS-485) data receiving timeout
(Unit: 1ms, min. 50ms, value smaller than
50ms will be regarded as 50ms) (only applicable
for MODRW/RS instruction) In RS instruction, no
time-out setting if “0” is specified
○ ○ ○ ○ 0 0 - R NO 0
○ ○ ○ ○ 0 0 - R NO 0
○ ○ ○ ○ 0 0 - R NO 0
○ ○ ○ ○ 0 0 - R NO 0
○ ○ ○ ○ 0 - - R/W NO 0
○ ○ ○ ○ 0 - - R/W NO 0
○ ○ ○ ○ 0 - - R/W NO 0
○ ○ ○ ○ 0 - - R/W NO 0
○ ╳ ○ ╳ 50 - - R/W NO 50
2-43