DVP-ES2-EX2-SS2-SA2-SX2-Operation Manual

DVP-ES2/EX2/SS2/SA2/SX2/SE Operation Manual - Programming
Special
M
Function
OFF
ES2
SS2 SA2 SX2
EX2
ON
STOP
RUN
RUN
STOP
Attrib. Latch
-ed
Default
M1233 C233 counter monitor (ON: count down) ○ ○ ○ ○ OFF - - R NO OFF
M1234 C234 counter monitor (ON: count down) ○ ○ ○ ○ OFF - - R NO OFF
M1235 C235 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF
M1236 C236 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF
M1237 C237 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF
M1238 C238 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF
M1239 C239 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF
M1240 C240 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF
M1241 C241 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF
M1242 C242 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF
M1243
M1244
C243 Reset function control. ON = R
function disabled
C244 Reset function control. ON = R
function disabled
○ ○ ○ ○ OFF - - R/W NO OFF
○ ○ ○ ○ OFF - - R/W NO OFF
M1245 C245 counter monitor (ON: count down) ○ ○ ○ ○ OFF - - R NO OFF
M1246 C246 counter monitor (ON: count down) ○ ○ ○ ○ OFF - - R NO OFF
M1247 C247 counter monitor (ON: count down) ○ ○ ○ ○ OFF - - R NO OFF
M1248 C248 counter monitor (ON: count down) ○ ○ ○ ○ OFF - - R NO OFF
M1249 C249 counter monitor (ON: count down) ○ ○ ○ ○ OFF - - R NO OFF
M1250 C250 counter monitor (ON: count down) ○ ○ ○ ○ OFF - - R NO OFF
M1251 C251 counter monitor (ON: count down) ○ ○ ○ ○ OFF - - R NO OFF
M1252 C252 counter monitor (ON: count down) ○ ○ ○ ○ OFF - - R NO OFF
M1253 C253 counter monitor (ON: count down) ○ ○ ○ ○ OFF - - R NO OFF
M1254 C254 counter monitor (ON: count down) ○ ○ ○ ○ OFF - - R NO OFF
Set the ramp up/down of Y0, Y2 to be “S
M1257
curve.” ON = S curve.
Set up X7 as the reset signal for software
M1260
counters C235 ~ C241
Enable cyclic output for table output
M1262 function of DPTPO instruction. ON =
enable.
C235 counting mode (ON: falling-edge
M1270
count)
C236 counting mode ON: falling-edge
M1271
count)
C237 counting mode (ON: falling-edge
M1272
count)
C238 counting mode (ON: falling-edge
M1273
count)
○ ○ ○ ○ OFF OFF - R/W NO OFF
○ ○ ○ ○ OFF - - R/W NO OFF
○ ○ ○ ○ OFF OFF - R/W NO OFF
○ ○ ○ ○ OFF - - R/W NO OFF
○ ○ ○ ○ OFF - - R/W NO OFF
○ ○ ○ ○ OFF - - R/W NO OFF
○ ○ ○ ○ OFF - - R/W NO OFF
2-24