Policy Framework Configuration Guide - Juniper Networks

More documents

Recommendations

Info

Junos 10.4 Policy Framework Configuration Guide 2. Include the source-address-only statement at the [edit forwarding-options hash-key family multiservice payload ip layer-3] hierarchy level to include information about the IP source address only in the hash key. 3. Include destination-address-only statement at the [edit forwarding-options hash-key family multiservice payload ip layer-3] hierarchy level to include information about the IP destination address only in the hash key. NOTE: You can configure either the source-address-only or the destination-address-only statements at a time, not both. They are mutually exclusive. To configure VPLS load balancing to include Layer 4 information: • Include the layer-4 statement at the [edit forwarding-options hash-key family multiservice payload ip] hierarchy level. The following example shows load balancing configured to use the source Layer 3 IP address option and Layer 4 header fields as well as the source and destination MAC addresses: [edit forwarding-options hash-key] family multiservice { source-mac; destination-mac; payload { ip { layer-3 { source-address-only; } layer-4; } } } Related Documentation • family multiservice on page 400 • hash-key on page 412 Example: Configuring Multicast Load Balancing over Aggregated Ethernet Links This example shows how to configure point-to-multipoint (P2MP) LSPs to load balance across aggregated Ethernet links. The load balancing applies to all traffic types, including multicast. • Requirements on page 153 • Overview on page 153 • Configuration on page 153 • Verification on page 164 152 Copyright © 2010, Juniper Networks, Inc.
Chapter 6: Extended Actions Configuration Requirements Before you begin: • Configure the router interfaces. See the Network Interfaces Configuration Guide. • Configure an interior gateway protocol or static routing. See the Routing Protocols Configuration Guide. Overview This example shows a sample topology and configuration to perform the following tasks: • Load balancing VPLS multicast traffic over link aggregation • Load balancing P2MP multicast traffic over link aggregation • Re-load balancing after a change in the nexthop topology Nexthop topology changes might include but are not limited to: • L2 membership change in the link aggregation • Indirect nexthop change • Composite nexthop change Figure 12 on page 153 shows the topology for this example. The example includes the configuration for PE1 and PE2. Figure 12: Multicast Load Balancing over Aggregated Ethernet Links AE links AE links PE1 PE2 CE2 AE links AE links P AE links PE3 g040625 Configuration CLI Quick Configuration To quickly configure load balancing across aggregated Ethernet links, copy the following commands into a text file, remove any line breaks, and then paste the commands into the CLI. PE1: Copyright © 2010, Juniper Networks, Inc. 153
Page 1 and 2:
Junos ® OS Policy Framework Config
Page 3 and 4:
END USER LICENSE AGREEMENT READ THI
Page 5 and 6:
12. Commercial Computer Software. T
Page 7 and 8:
Abbreviated Table of Contents Part
Page 9 and 10:
Table of Contents About This Guide
Page 11 and 12:
Table of Contents Testing Routing P
Page 13 and 14:
Table of Contents Using Routing Pol
Page 15 and 16:
Table of Contents Configuring Forwa
Page 17 and 18:
Table of Contents Configuring Flow
Page 19 and 20:
Table of Contents interface (Next-H
Page 21 and 22:
List of Figures Part 1 Policy Frame
Page 23 and 24:
List of Tables About This Guide . .
Page 25 and 26:
About This Guide This preface provi
Page 27 and 28:
About This Guide • MX Series •
Page 29 and 30:
About This Guide Table 1: Notice Ic
Page 31 and 32:
About This Guide or are covered und
Page 33 and 34:
PART 1 Policy Framework • Introdu
Page 35 and 36:
CHAPTER 1 Introduction to Policy Fr
Page 37 and 38:
Chapter 1: Introduction to Policy F
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
PART 2 Routing Policies • Introdu
Page 47 and 48:
CHAPTER 2 Introduction to Routing P
Page 49 and 50:
Chapter 2: Introduction to Routing
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
CHAPTER 3 Routing Policy Configurat
Page 69 and 70:
Chapter 3: Routing Policy Configura
Page 71 and 72:
CHAPTER 4 Routing Policy Configurat
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
CHAPTER 5 Extended Match Conditions
Page 129 and 130:
Chapter 5: Extended Match Condition
Page 131 and 132:
Chapter 5: Extended Match Condition
Page 133 and 134: Chapter 5: Extended Match Condition
Page 167 and 168: CHAPTER 6 Extended Actions Configur
Page 169 and 170: Chapter 6: Extended Actions Configu
Page 183: Chapter 6: Extended Actions Configu
Page 197 and 198: CHAPTER 7 Summary of Routing Policy
Page 199 and 200: Chapter 7: Summary of Routing Polic
Page 213 and 214: PART 3 Firewall Filters • Introdu
Page 215 and 216: CHAPTER 8 Introduction to Firewall
Page 217 and 218: Chapter 8: Introduction to Firewall
Page 223 and 224: CHAPTER 9 Firewall Filter Configura
Page 225 and 226: Chapter 9: Firewall Filter Configur
Page 235 and 236:
Chapter 9: Firewall Filter Configur
Page 237 and 238:
Page 239 and 240:
Page 241 and 242:
Page 243 and 244:
Page 245 and 246:
Page 247 and 248:
Page 249 and 250:
Page 251 and 252:
Page 253 and 254:
Page 255 and 256:
Page 257 and 258:
Page 259 and 260:
Page 261 and 262:
Page 263 and 264:
Page 265 and 266:
Page 267 and 268:
Page 269 and 270:
Page 271 and 272:
Page 273 and 274:
Page 275 and 276:
Page 277 and 278:
Page 279 and 280:
Page 281 and 282:
Page 283 and 284:
Page 285 and 286:
Page 287 and 288:
Page 289 and 290:
Page 291 and 292:
Page 293 and 294:
Page 295 and 296:
Page 297 and 298:
Page 299 and 300:
Page 301 and 302:
Page 303 and 304:
Page 305 and 306:
Page 307 and 308:
Page 309 and 310:
CHAPTER 10 Introduction to Traffic
Page 311 and 312:
Chapter 10: Introduction to Traffic
Page 313 and 314:
Page 315 and 316:
CHAPTER 11 Policer Configuration Si
Page 317 and 318:
Chapter 11: Policer Configuration [
Page 319 and 320:
Chapter 11: Policer Configuration I
Page 321 and 322:
Chapter 11: Policer Configuration C
Page 323 and 324:
Chapter 11: Policer Configuration u
Page 325 and 326:
Chapter 11: Policer Configuration T
Page 327 and 328:
Chapter 11: Policer Configuration
Page 329 and 330:
Chapter 11: Policer Configuration }
Page 331 and 332:
Chapter 11: Policer Configuration N
Page 333 and 334:
Chapter 11: Policer Configuration }
Page 335 and 336:
Page 337 and 338:
Chapter 11: Policer Configuration A
Page 339 and 340:
Chapter 11: Policer Configuration p
Page 341 and 342:
Page 343 and 344:
Chapter 11: Policer Configuration p
Page 345 and 346:
Chapter 11: Policer Configuration c
Page 347 and 348:
CHAPTER 12 Summary of Firewall Filt
Page 349 and 350:
Chapter 12: Summary of Firewall Fil
Page 351 and 352:
Page 353 and 354:
Page 355 and 356:
Page 357 and 358:
Page 359 and 360:
Page 361 and 362:
Page 363 and 364:
Page 365 and 366:
Page 367 and 368:
Page 369 and 370:
Page 371 and 372:
Page 373 and 374:
PART 4 Traffic Sampling, Forwarding
Page 375 and 376:
Page 377 and 378:
Page 379 and 380:
Page 381 and 382:
Page 383 and 384:
Page 385 and 386:
Page 387 and 388:
Page 389 and 390:
Page 391 and 392:
CHAPTER 15 Traffic Forwarding and M
Page 393 and 394:
Chapter 15: Traffic Forwarding and
Page 395 and 396:
Page 397 and 398:
Page 399 and 400:
Page 401 and 402:
Page 403 and 404:
Page 405 and 406:
Page 407 and 408:
Page 409 and 410:
Page 411 and 412:
Page 413 and 414:
Page 415 and 416:
CHAPTER 16 Summary of Traffic Sampl
Page 417 and 418:
Chapter 16: Summary of Traffic Samp
Page 419 and 420:
Page 421 and 422:
Page 423 and 424:
Page 425 and 426:
Page 427 and 428:
Page 429 and 430:
Page 431 and 432:
Page 433 and 434:
Page 435 and 436:
Page 437 and 438:
Page 439 and 440:
Page 441 and 442:
Page 443 and 444:
Page 445 and 446:
Page 447 and 448:
Page 449 and 450:
Page 451 and 452:
Page 453 and 454:
Page 455 and 456:
Page 457 and 458:
Page 459 and 460:
Page 461 and 462:
Page 463 and 464:
Page 465 and 466:
Page 467 and 468:
Page 469 and 470:
Page 471 and 472:
Page 473 and 474:
Page 475 and 476:
Page 477 and 478:
Page 479 and 480:
Page 481 and 482:
Page 483 and 484:
Page 485 and 486:
Page 487 and 488:
Page 489 and 490:
Page 491 and 492:
PART 5 Indexes • Index on page 46
Page 493 and 494:
Index Symbols ! in policy expressio
Page 495 and 496:
Index Layer 2 bridging traffic (MX
Page 497 and 498:
Index input statement..............
Page 499 and 500:
Index P P2MP.......................
Page 501 and 502:
Index show policy damping command..
Page 503 and 504:
Index of Statements and Commands A
Page 505 and 506:
Index of Statements and Commands si
show all

Policy Framework Configuration Guide - Juniper Networks

Create successful ePaper yourself

Delete template?

Save as template?