User Manual - John Preston
User Manual - John Preston User Manual - John Preston
1.6 Backrest angle of inclination adjustment Standard seat – Loosen and remove the four star grips [15]. – Pull or push the backrest [14] to the desired position. – Screw the four star grips [15] back in and tighten them. 14 15 14 ! By adjusting the angle of inclination, the height of the backrest is also altered. It may be necessary to re-set the height (see chapter 1.4).
10 1.7 Seat length adjustment Function seat (standard and comfort upholstery) – Pull the cushion off the seat. – Loosen and remove the four screws holding the seat. – On the inside of the seat there are 5 holes in each of two rows which are normally covered by the upholstery. Feel for these holes with a sharp object. 16 16 – Select the hole [16] which will provide the desired seat length for you. – With a sharp knife, cut an opening into the upholstery over the chosen holes. – As an alternative to a knife a soldering iron may also be used. When the screw holes melt it should leave an even, clean and heat-sealed border around the holes. – Screw the seat back on in the position you have selected. – Replace the cushion on the seat.
- Page 1 and 2: Adventure A10 Informationen für Th
- Page 3 and 4: Contents 1 Mechanical adjustments
- Page 5 and 6: 1 Mechanical adjustments to the adv
- Page 7 and 8: 1.3 Armrest sideways adjustment 9 -
- Page 9: 1.5 Backrest angle of inclination a
- Page 13 and 14: 12 1.9 Leg support length adjustmen
- Page 15 and 16: 14 1.11 Leg support footrest length
- Page 17 and 18: 16 1.13 Adjusting the chassis sprin
- Page 19 and 20: 18 31 1.14 Setting the direction in
- Page 21 and 22: 20 1.16 Setting the seat position S
- Page 23 and 24: 22 1.17.2 Mudguards for the powered
- Page 25 and 26: 2 Settings on the control unit 24 2
- Page 27 and 28: 26 Turning speed - Determines the m
- Page 29 and 30: 28 Speed reduction This parameter c
- Page 31 and 32: 30 2.6 Changing the parameters Afte
- Page 33 and 34: 32 2.8 Parameter table 2.8.1 advent
- Page 35 and 36: 34 2.8.3 adventure version 12 km/h
- Page 37 and 38: 36 Drive symbol flashes Exclamation
- Page 39 and 40: 38 Drive symbol flashes Exclamation
- Page 41 and 42: 40 Interface symbol flashes Exclama
- Page 43 and 44: 42 Complete seat unit* flashes Inte
- Page 45 and 46: 44 Brake symbol flashes Battery cap
10<br />
1.7 Seat length adjustment<br />
Function seat (standard and comfort<br />
upholstery)<br />
– Pull the cushion off the seat.<br />
– Loosen and remove the four screws holding the seat.<br />
– On the inside of the seat there are 5 holes in each of two<br />
rows which are normally covered by the upholstery.<br />
Feel for these holes with a sharp object.<br />
16 16<br />
– Select the hole [16] which will provide the desired seat<br />
length for you.<br />
– With a sharp knife, cut an opening into the upholstery over<br />
the chosen holes.<br />
– As an alternative to a knife a soldering iron may also be<br />
used. When the screw holes melt it should leave an even,<br />
clean and heat-sealed border around the holes.<br />
– Screw the seat back on in the position you have selected.<br />
– Replace the cushion on the seat.