Operating Manual - John Morris Scientific

More documents

Recommendations

Info

Menu functions >Edit Profile: 1 Step: 3 Setp: 50.00°C Time [hh:mm] 00:02 Example: >Delete Prof. 4 from Step to Step 8 34 delete yes >Delete Prof. from Step 4 8 to Step 34 ****** delete ****** Display sections (Step): 1 Use the keys to select the submenu „Step“, enter the desired number and press enter or 2 If the submenu „Step“ is selected, section by section can be shown in ascending order by the key . Each previously set value is displayed. Delete: A flashing segment indicates that the respective profile number needs to be entered in which one or more consecutive sections are to be deleted. Example: Delete step 8 to step 34 in profile 4. Line 4 indicates the deletion. yes Example: >Print Profile 2 Print yes >Print Profile 2 ****** print ******* Print: Each profile may be printed via the serial interface for control or documentation. A flashing segment indicates that the number of the profile to be printed needs to be entered. Example: Print profile 2 yes Printing is indicated in line 2. >hour.min 14:24 Day.Mon 07.12 Year 2003 14:24:36 Setting clock The integrated clock allows starting a profile at any date and time. The clock is preset in the factory. Lines 1 to 3: Check for correctness of the preset date and time and correct if necessary. The time is diplayed permanently in line 4. 48
Ultra-Low Refrigerated Circulators 6.5. Analog inputs/outputs ALARM STAND-BY REG+ E-PROG In order to use the analog inputs and outputs, the circulator must be equipped with the electronics module available as option. Order No. 8 900 100 Electronic module This submenu enables setting of the input and output values for the programmer input and the temperature recorder outputs of socket REG+E-PROG. The >STAND-BY< input and the >ALARM< output are configurable. If the electronic module is not fitted, this menu can only be used to switch control of the solenoid valve. Int. Programmer >Input/Output Limits Interface serial ESC Indication without electronic module Inputs/Outputs >SV-Out. : Backflow /C-Puls ESC Inputs/Outputs >SV-Out. : Backflow /C-Puls Chan.1 : ActInt Chan.2 : Power Chan.3 : Setpoint EPROG : Setpoint Ext.StBy : inactive /active AlarmOut : StdBy >Chan.1 : ActInt / 0V = -99.9°C 10V = 400.0°C ActExt/Power/Setpoint 1 >Chan.2 : Power / 0V = 0.00% 10V = 100% ActInt/ActExt/Setpoint 1 ESC >Chan.3 : Setpoint / ActExt/ACtInt/Power 0mA = -99.9°C 20mA = 400.0°C 1 Region: 0-20mA /4-20mA >EPROG : Setpoint / ActVar (%)/Flowrate(l/min) Signal : Voltage /Current L Value -99.9°C REM: % / l/Min H Value 400.0°C REM: % / l/Min Setpoint : xx.xx°C REM: % / l/Min 1 AlarmOut >Function: StdBy /Alarm/Al+StBy Type : normal /invers NOTE: Channel 2 is pre-configured for connecting a HST Booster heater. 49
Page 1 and 2: 80 40 0 160 240 320 Operating Manua
Page 3 and 4: Ultra-Low Refrigerated Circulators
Page 19 and 20: Caution: Ultra-Low Refrigerated Cir
Page 47: Int. Programmer >Edit Delete Print
Page 55 and 56: Alarm output (10) (for external ala
Page 65 and 66: WARNING CODE 21 WARNING CODE 22 WAR
Page 77 and 78: Error messages Description -08 INVA

Operating Manual - John Morris Scientific

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?