819 Injection Module User's Guide (PDF) - John Morris Scientific

More documents

Recommendations

Info

5 Troubleshooting Electrical ................................................................................ 5-2 Input Functions Not Operating .................................. 5-2 Output Functions Not Operating .............................. 5-2 Unit Not Operational ................................................... 5-3 Unit Blows Fuses ........................................................... 5-3 LEDs Flashing On Front Panel ................................... 5-3 Mechanical ............................................................................ 5-4 Bubbling Liquid From Injection Port ......................... 5-4 Bubbling Liquid From Waste Port or Injection Port ............................................................. 5-4 Repair and Return Policies ................................................ 5-5 Before Calling Us........................................................... 5-5 Warranty Repair ........................................................... 5-5 Non-Warranty Repair .................................................. 5-5 Rebuilt Exchange........................................................... 5-5 Return Procedure .......................................................... 5-6 Appendix A Appendix B Appendix C Appendix D Replacement Parts and Accessories GSIOC Commands GSIOC Commands .............................................................. B-2 GSIOC Command List ................................................. B-2 Baud Rate Specifications Methods Injection Carryover Method .............................................. D-2 System ............................................................................. D-2 Mobile Phase/Rinse Solvent ....................................... D-3 Flow Rate ........................................................................ D-3 Injection .......................................................................... D-3 Rinse Volume ................................................................. D-3 Injections ......................................................................... D-3 Calibration Curve Parameters .................................... D-3 Injection Protocol .......................................................... D-4 Injection Reproducibility Method ..................................... D-5 System ............................................................................. D-5 Mobile Phase .................................................................. D-5 Flow Rate ........................................................................ D-5 Injection .......................................................................... D-5 Rinse Volume ................................................................. D-6 Injection Volume ........................................................... D-6
Appendix E Using an Additional 819 Module for Fraction Collection Required Accessories........................................................... E-2 Electrical Connections ........................................................ E-3 Making Contact Connections ..................................... E-3 Plumbing Connections........................................................ E-4 At Initialization .................................................................... E-6 Example UniPoint Method ................................................ E-7
Page 1: 819 Injection Module User’s Guide
Page 7: Declaration of Conformity Applicati
Page 10 and 11: Introduction 1 Unpacking Unpacking
Page 12 and 13: Introduction 1 Technical Specificat
Page 14 and 15: Introduction 1 Technical Specificat
Page 16 and 17: Installation 2 Installing the Injec
Page 18 and 19: Installation 2 Making Electrical Co
Page 26 and 27: Installation 2 Adjusting the 215’
Page 28 and 29: Installation 2 Adjusting the Liquid
Page 34 and 35: Operation 3 Front Panel Front Panel
Page 37 and 38: Maintenance 4 To obtain optimum per
Page 39 and 40: Maintenance 4 Replacing Parts Repla
Page 41 and 42: Maintenance 4 Replacing the Injecti
Page 43 and 44: Maintenance 4 Replacing a Fuse A bl
Page 45 and 46: Troubleshooting 5 5-1
Page 47 and 48: Troubleshooting 5 Unit Not Operatio
Page 49 and 50: Troubleshooting 5 Repair and Return
Page 51 and 52: Replacement Parts and Accessories A
Page 53 and 54: Appendix A 251773 Prep FC package (
Page 55:
Appendix A 49942107 0.8 mm ID Teflo
Page 58 and 59:
Appendix B GSIOC Commands GSIOC Com
Page 61 and 62:
Baud Rate C As a default, the baud
Page 63 and 64:
Specifications Methods D This appen
Page 65 and 66:
Appendix D Mobile Phase/Rinse Solve
Page 67 and 68:
Appendix D Injection Reproducibilit
Page 69 and 70:
Using an Additional 819 Module for
Page 71 and 72:
Appendix E Electrical Connections M
Page 73 and 74:
Appendix E Using an Additional 819
Page 75:
Appendix E Example UniPoint Method
show all

819 Injection Module User's Guide (PDF) - John Morris Scientific

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?