819 Injection Module User's Guide (PDF) - John Morris Scientific

More documents

Recommendations

Info

Introduction 1 Technical Specifications Technical Specifications Please be aware of the following before operating the 819 Injection Module. Warning: Changes or modifications to this unit not expressly approved by Gilson could void your factoryauthorized warranty. This unit has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC commercial environment. This unit generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. Operation of this unit in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Shielded cables must be used with this unit to ensure compliance with the Class A FCC limits. 1-4
Introduction 1 Technical Specification Available sample loops Definition Available valves Rheodyne 7010 Contact control Environmental conditions 5 µL, 10 µL, 20 µL, 50 µL, 100 µL, 200 µL, 1 mL, 2 mL, 5 mL, and 10 mL One contact closure output and one contact closure input Indoor use Altitude: up to 2000 m Temperature range: 5–40°C Air pressure: 75–105 kPa Pollution degree: 1 or 2, in accordance with IEC 66 Humidity: Maximum relative humidity 80% for temperatures up to 31°C, decreasing linearly to 50% relative humidity at 40°C Technical Specifications Front panel Injection carryover Injection reproducibility Liquid contact materials Manufacturing standards Power requirements LOAD and INJECT LED lights 0.01% using equipment and method described in Appendix D. See Appendix D for details about the configuration and test procedure that Gilson used to determine the limits below. Total loop fill: CV
Page 1: 819 Injection Module User’s Guide
Page 4 and 5: 5 Troubleshooting Electrical ......
Page 7: Declaration of Conformity Applicati
Page 10 and 11: Introduction 1 Unpacking Unpacking
Page 14 and 15: Introduction 1 Technical Specificat
Page 16 and 17: Installation 2 Installing the Injec
Page 18 and 19: Installation 2 Making Electrical Co
Page 26 and 27: Installation 2 Adjusting the 215’
Page 28 and 29: Installation 2 Adjusting the Liquid
Page 34 and 35: Operation 3 Front Panel Front Panel
Page 37 and 38: Maintenance 4 To obtain optimum per
Page 39 and 40: Maintenance 4 Replacing Parts Repla
Page 41 and 42: Maintenance 4 Replacing the Injecti
Page 43 and 44: Maintenance 4 Replacing a Fuse A bl
Page 45 and 46: Troubleshooting 5 5-1
Page 47 and 48: Troubleshooting 5 Unit Not Operatio
Page 49 and 50: Troubleshooting 5 Repair and Return
Page 51 and 52: Replacement Parts and Accessories A
Page 53 and 54: Appendix A 251773 Prep FC package (
Page 55: Appendix A 49942107 0.8 mm ID Teflo
Page 58 and 59: Appendix B GSIOC Commands GSIOC Com
Page 61 and 62: Baud Rate C As a default, the baud
Page 63 and 64:
Specifications Methods D This appen
Page 65 and 66:
Appendix D Mobile Phase/Rinse Solve
Page 67 and 68:
Appendix D Injection Reproducibilit
Page 69 and 70:
Using an Additional 819 Module for
Page 71 and 72:
Appendix E Electrical Connections M
Page 73 and 74:
Appendix E Using an Additional 819
Page 75:
Appendix E Example UniPoint Method
show all

819 Injection Module User's Guide (PDF) - John Morris Scientific

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?