Bully Dog 40300 Computer Chip Programmer Installation ... - Jegs

More documents

Recommendations

Info

PMT INSTALLATION Introduction Parts Description PMT Installation Operating Instructions Internet Updates Appendix Section 3: Installing the OBDII Adapter plug 3. Locate the OBDII port on the vehicle; OBDII ports are located under the dash on the driver’s side. These ports are located in different areas under the dash for different vehicle applications; see the OBDII port locations diagram. 4. Plug the OBDII Adapter Plug into the OBDII port; see the Installed OBDII Adapter Plug diagram for an example of the finished install. OBDII Adapter Plug Installation Diagram Cradle Cable PMT & Cradle OBDII Adapter Plug OBDII Plug PCH Cable Peripheral Cable Port OBDII Port Locations Diagram GM Dodge OBDII Port Locations Ford 25
PMT INSTALLATION Section 4: Installing the pOWer Wire In this section you will run the Power Wire coming from the PMT Cradle to the vehicle fuse box and connect it to the fuse locations specified below. The fuse location for the Power Wire is different on each vehicle application. CONNECTING THE POWER WIRE: 1. Locate the fuse box: Ford fuse boxes are located under the dash inside the cab of the vehicle; Dodge and GM fuse boxes are located on the driver’s side of the vehicle inside the engine bay. Please see your owner’s manual for more details on fuse box locations. Once inside the fuse box, locate the appropriate fuse depicted in the vehicle-specific pictures below. ‘01-’07 GM: Fuse “ING E” ‘03-’05 Ford: Fuse #33 Power Wire w/90º Connector ‘03-’07 Dodge: Fuse #28 ‘06-’07 Ford: Fuse #26 2. Remove the fuse, indicated in the pictures, and insert the fuse jack. Make sure that the fuse jack is placed on the dead side of the fuse to ensure that the PMT is protected by the fuse. Use a volt meter to verify the dead side of the fuse. With the fuse pulled and the truck powered on but not started, the volt meter should read 0 volts on the fuse jack to ground. Problems that can occur if the incorrect fuse is used for this connection: the power may stay on continuously even with the key off; or, the PMT can receive power at the incorrect time of the power-on/starting cycle of the vehicle. 3. If installing on a Dodge or a GM, run the power wire through the fire wall before preparing the Power Wire. Prepare the Power Wire by stripping the end of the wire about ¼”. Connect the blue 90° connector to the end of the Power Wire using crimping pliers. 4. Connect the Power Wire to the fuse jack, place the fuse back into the slot, and close the fuse box. Introduction Parts Description PMT Installation Operating Instructions Internet Updates Appendix 26
Page 1 and 2: INSTALLATION Manual Vehicle Applica
Page 3 and 4: INTRODUCTION OPERATING INSTRUCTIONS
Page 5 and 6: BILL OF MATERIALS Bill of Materials
Page 7 and 8: PARTS DESCRIPTION Pyrometer Connect
Page 9 and 10: PMT INSTALLATION Installation Overv
Page 11 and 12: PMT INSTALLATION PMT Installation I
Page 13 and 14: PMT INSTALLATION 2. With all assemb
Page 15 and 16: PMT INSTALLATION Dash Mounting Dash
Page 17 and 18: PMT INSTALLATION To mount the dash
Page 19 and 20: PMT INSTALLATION Windshield Mountin
Page 21 and 22: PMT INSTALLATION Installing the Pyr
Page 23 and 24: PMT INSTALLATION Post-turbo MOUNT 1
Page 25: PMT INSTALLATION Section 3: Install
Page 29 and 30: OPERATING INSTRUCTIONS PMT OPERATIN
Page 31 and 32: OPERATING INSTRUCTIONS SETUP WIZARD
Page 33 and 34: OPERATING INSTRUCTIONS Section 3: e
Page 35 and 36: OPERATING INSTRUCTIONS Large Gauge
Page 37 and 38: OPERATING INSTRUCTIONS CHANGE VEHIC
Page 39 and 40: OPERATING INSTRUCTIONS Downloading
Page 41 and 42: OPERATING INSTRUCTIONS Calibrating
Page 43 and 44: OPERATING INSTRUCTIONS Gauge Setup
Page 45 and 46: OPERATING INSTRUCTIONS PMT VEHICLE
Page 47 and 48: OPERATING INSTRUCTIONS Adjust backl
Page 49 and 50: OPERATING INSTRUCTIONS ADJUST VOLUM
Page 51 and 52: OPERATING INSTRUCTIONS Reset to def
Page 53 and 54: OPERATING INSTRUCTIONS Set Defuel L
Page 55 and 56: OPERATING INSTRUCTIONS ADJUST TIRE
Page 57 and 58: OPERATING INSTRUCTIONS SHOW SETTING
Page 59 and 60: OPERATING INSTRUCTIONS NO SD CARD N
Page 61 and 62: INTERNET UPDATES Section 1: PMT Ver
Page 63 and 64: INTERNET UPDATES Section 3: The Upd
Page 65 and 66: APPENDIX Section 2: Transmission Re
Page 67 and 68: Appendix APPENDIX Section 4: PMT Tr
Page 69 and 70: APPENDIX Appendix 4. With the forma
Page 71 and 72: APPENDIX SECTION 6: warranty & disc

Bully Dog 40300 Computer Chip Programmer Installation ... - Jegs

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?