D-Series Syringe Pumps - Isco

More documents

Recommendations

Info

D Series Syringe Pumps Section 9 Modifier Addition DANGER RISK OF INJURY. THE PRESSURE PRODUCED COULD BE 700 BAR. PLEASE UTILIZE APPRO- PRIATE TUBING AND CONNECTIONS NOTED IN THE MANUAL. Figure 9-1 Modifier addition kit installation Note Figure 9-1 shows the two pumps with the refill kits installed. The instructions for this are provided in sections 2A.3.1 and 2B.3.1 (Figure 2A-4). When preparing your system for modifier operation, if you are connecting pump A to a CO 2 tank, you will need to use the stainless steel tubing (P/N 60-1243-391) and appropriate CO 2 connecting fittings. If you do not have these fittings, a CO 2 cylinder connection package (P/N 68-1247-043) may be ordered from Teledyne Isco. 9-4
D Series Syringe Pumps Section 9 Modifier Addition 9.3 Initial Preparation for Modifier Addition When first setting up the D Series pump system under modifier mode, the pumps should be zeroed and filled. To accomplish this, the pumps should first be placed under independent control - constant pressure mode. Note Once the modifier system is operating, the system does not need to be zeroed before refilling. To designate independent control (constant pressure mode) To designate constant pressure To zero the pumps To fill pump B with modifier 1. If the pumps are running, press the STOP key once. 2. Press the MENU key. 3. Press softkey A - MORE. 4. Press 4 - MULTI-PUMP, to display the multi-pump menu. 5. Press 4 - INDEPENDENT to designate that the pumps be operated under independent control. The number 4 will blink, indicating that independent has been selected. 6. Press softkey D - PREVIOUS, twice to return to the main menu. 1. Press the blue CONST PRESS key on the front panel keypad. 1. Place the pumps in independent control - constant pressure mode, as detailed above. 2. Be sure the pumps are stopped. 3. Disconnect the inlet tubing from the inlet valve of pump A. 4. Select 2 pump independent control/constant pressure mode. 5. Open the inlet valves of each pump. 6. Run both pumps to their empty positions. 7. Zero the pressure on each pump. 8. Reconnect the pump A inlet tubing to the inlet valve. 1. Place the pumps in independent control - constant pressure mode, as detailed above. 2. Be sure the pumps are stopped. 3. Close the pump B outlet valve and open the pump B inlet valve. 4. Press the REFILL key on the front panel keypad. Press softkey B to designate that pump B is the active pump (the pump being refilled). Pump B will fill with modifier. 5. After pump B has filled, press run and deliver 5-10 ml of modifier back through the inlet valve, to ensure all air is purged from the pump, before pressing stop. 6. Close the inlet valve. 9-5
Page 1:
D-Series Pumps Installation and Ope
Page 5 and 6:
D Series Syringe Pumps Warnings, Ca
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
D Series Syringe Pumps Table of Con
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
D Series Syringe Pumps Section 1 In
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
D Series Syringe Pumps: Models 65DM
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
D Series Syringe Pumps: Model 500D
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
D Series Syringe Pumps: Model 65D S
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
D Series Syringe Pumps Section 3 Si
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
D Series Syringe Pumps Section 4 Th
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
D Series Syringe Pumps Section 5 Pu
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
D Series Syringe Pumps Section 6 Se
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150: D Series Syringe Pumps Section 6 Se
Page 165 and 166: D Series Syringe Pumps Section 7 Gr
Page 177 and 178: D Series Syringe Pumps Section 8 Co
Page 197 and 198: D Series Syringe Pumps Section 9 Mo
Page 199: D Series Syringe Pumps Section 9 Mo
Page 207 and 208: D Series Syringe Pumps Appendix A R
Page 251 and 252:
D Series Syringe Pumps Appendix A R
Page 253 and 254:
Page 255 and 256:
Page 257 and 258:
Page 259 and 260:
Page 261 and 262:
Page 263 and 264:
Page 265 and 266:
Page 267 and 268:
Page 269 and 270:
Page 271 and 272:
Page 273 and 274:
Page 275 and 276:
Page 277 and 278:
D Series Syringe Pumps Index A Acc
Page 279 and 280:
D Series Syringe Pumps Index comman
Page 281:
Compliance Statements NOTICE Disreg
Page 285:
DECLARATION OF CONFORMITY Applicati
Page 288 and 289:
Warranty
show all

D-Series Syringe Pumps - Isco

Create successful ePaper yourself

Delete template?

Save as template?