D-Series Syringe Pumps - Isco

More documents

Recommendations

Info

D Series Syringe Pumps Section 6 Serial Interface Command MAXPRESSA=# MAXPRESSB=# MAXPRESSC=# MAXPRESSA MAXPRESSB MAXPRESSC MFLOWA=# MFLOWB=# MFLOWC=# MFLOWA MFLOWB MFLOWC MINFLOWA=# MINFLOWB=# MINFLOWC=# MINFLOWA MINFLOWB MINFLOWC MINPRESSA=# MINPRESSB=# MINPRESSC=# MINPRESSA MINPRESSB MINPRESSC MODIFIER PRESS=# PRESSB=# PRESSC=# PRESS PRESSA PRESSB PRESSC PRESSCNTRLDIFF1 PRESSCNTRLDIFF1=XXXXX PRESSCNTRLDIFF2 PRESSCNTRLDIFF3 PRESSCNTRLNORM PRESSDIFF=XXXXX PRESSDIFF Table 6-4 Serial Commands (Continued) Description Enter # to designate the maximum pressure setpoint. Returns the maximum pressure setpoint. Enter # to designate the maximum flow limit in constant pressure mode. Returns the maximum flow limit setpoint. Enter # to designate the minimum flow rate setpoint. Returns the minimum flow rate setpoint. Returns the minimum flow rate setpoint. Returns the minimum pressure setpoint. Put pumps in modifier addition mode. Enter # to designate pressure setpoint (constant pressure mode). Returns the delivering pump pressure in continuous pumping mode and modifier addition mode. In INDEPENDENT mode it returns the pump A pressure. Returns the actual pressure of the pump. Sets the pressure control input to Analog input 1, with a pressure range of 50 psi. Sets the pressure control input to Analog input 1 and sets the pressure range. The range is 1 to 5000. the units are psi, with a value of 5000 representing 5000 psi at 5 volts. Sets the pressure control input to Analog input 2, with a pressure range of 500 psi at 5 volts. Sets the pressure control input to Analog input 2, with a pressure range of 5000 psi at 5 volts. Sets the pressure control input to the standard input. Differential pressure setpoint. (PSI*10) 0 to 50,000 maximum (0 to 5000 psi) Reads the differential pressure value. (PSI*10) The transducer can also be read via the “ANGLx” serial commands. 6-14
D Series Syringe Pumps Section 6 Serial Interface Command RANGEA RANGEB RANGEC RAPIDA RAPIDB RAPIDC REFILL REFILLB REFILLC REFILL=# REFILLB=# REFILLC=# REMOTE RLIMITA RLIMITB RLIMITC RSVP RSVPB RSVPC RUN RUNB RUNC SETFLOWA SETFLOWB SETFLOWC SETPRESSA SETPRESSB SETPRESSC STATUSA STATUSB STATUSC STOP STOPB STOPC UNITSA= VOLA VOLB VOLC VOLTOT VOL RESET Table 6-4 Serial Commands (Continued) Description Provides scaling information for the system parameters. See 6.5.4 for more information about this serial command. Activates the automatic rapid pressurization cycle (constant flow mode only). Move cylinder to bottom at preset refill rate. Enter # to designate refill rate. Disables controller front panel control and enables all serial commands. Stops all motors (if control was previously local). Returns the refill flow rate limit. Pump responds with “READY” message. Same as front panel. Initiates pumping. Returns the flow rate setpoint. Returns the pressure setpoint. Returns with status of pump. May be any combination of responses listed below. STATUS= STOP PROBLEM= OVER PRESSURE RUN UNDER PRESSURE REFILL CYLINDER FULL HOLD CYLINDER EMPTY EQUIL. MOTOR FAILURE LOCAL REMOTE EXTERNAL Same as front panel, except that pump remains under remote serial control. Enter the desired flow or pressure units after the equal sign. Acceptable values are: ATM, BAR, KPA, PSI, ML/MIN, ML/HR, UL/MIN, UL/HR. (Sets all pumps.) Return the volume remaining in cylinder in ml. Format is “XXX.XXXX” ml. Returns the total volume delivered when using continuous flow or modifier. Will reset the volume total to zero. 6-15
Page 1:
D-Series Pumps Installation and Ope
Page 5 and 6:
D Series Syringe Pumps Warnings, Ca
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
D Series Syringe Pumps Table of Con
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
D Series Syringe Pumps Section 1 In
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
D Series Syringe Pumps: Models 65DM
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
D Series Syringe Pumps: Model 500D
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
D Series Syringe Pumps: Model 65D S
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
D Series Syringe Pumps Section 3 Si
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104: D Series Syringe Pumps Section 3 Si
Page 105 and 106: D Series Syringe Pumps Section 3 Si
Page 107 and 108: D Series Syringe Pumps Section 4 Th
Page 119 and 120: D Series Syringe Pumps Section 5 Pu
Page 141 and 142: D Series Syringe Pumps Section 6 Se
Page 153: D Series Syringe Pumps Section 6 Se
Page 165 and 166: D Series Syringe Pumps Section 7 Gr
Page 177 and 178: D Series Syringe Pumps Section 8 Co
Page 197 and 198: D Series Syringe Pumps Section 9 Mo
Page 205 and 206:
D Series Syringe Pumps Section 9 Mo
Page 207 and 208:
D Series Syringe Pumps Appendix A R
Page 209 and 210:
Page 211 and 212:
Page 213 and 214:
Page 215 and 216:
Page 217 and 218:
Page 219 and 220:
Page 221 and 222:
Page 223 and 224:
Page 225 and 226:
Page 227 and 228:
Page 229 and 230:
Page 231 and 232:
Page 233 and 234:
Page 235 and 236:
Page 237 and 238:
Page 239 and 240:
Page 241 and 242:
Page 243 and 244:
Page 245 and 246:
Page 247 and 248:
Page 249 and 250:
Page 251 and 252:
Page 253 and 254:
Page 255 and 256:
Page 257 and 258:
Page 259 and 260:
Page 261 and 262:
Page 263 and 264:
Page 265 and 266:
Page 267 and 268:
Page 269 and 270:
Page 271 and 272:
Page 273 and 274:
Page 275 and 276:
Page 277 and 278:
D Series Syringe Pumps Index A Acc
Page 279 and 280:
D Series Syringe Pumps Index comman
Page 281:
Compliance Statements NOTICE Disreg
Page 285:
DECLARATION OF CONFORMITY Applicati
Page 288 and 289:
Warranty
show all

D-Series Syringe Pumps - Isco

Create successful ePaper yourself

Delete template?

Save as template?