2150EX AV Flow Module - Isco

More documents

Recommendations

Info

2150EX Area Velocity Flow System Section 2 Preparation and Installation The scissors mechanism has stainless steel ground terminals mounted on the hinged bracket for the attachment of bonding conductors. Figure 2-26 Scissors mechanism ground terminals 2.8.3 Completing the AV Sensor Installation The AV sensor installation is finished by securing any excess sensor cable using cable clamps or other means. The reference tube inside the cable can be restricted or blocked if the cable is kinked, sharply bent, coiled, or otherwise pinched. The sensor cable should be handled and mounted with care. Also, if there is any appreciable distance between the point where the sensor cable leaves the mounting apparatus and the location of the flow meter, be sure to attach the cable to the flow stream wall to prevent it from vibrating, moving around, tangling, or possibly collecting debris. WARNING Do not coil the sensor cable. This will form an inductor and create hazard. 2-36
2150EX Area Velocity Flow System Section 2 Preparation and Installation CAUTION Under no circumstances should you leave any extra length of sensor cable dangling freely in the flow stream where it could trap debris or become tangled. Use gloves and eye protection when assembling and installing the rings in a pipe. Though deburred, the edges of the stainless steel can cut if improperly handled. Please read the information on how best to install this device. Observe general safety procedures when entering any manhole. See “General Safety Procedures” in the back of the manual for more information on general hazards and necessary precautions. 2.9 Final Installation Check The system should be secured at the site. This prevents damage caused by accidental falls and from being swept away if the channel is flooded. In manholes, the module is often secured to a ladder rung. Teledyne Isco’s Customer Service Department or your local representative can assist you with installation options. As you complete the installation, the following should be checked before leaving the site unattended: 1. The module should be positioned where it will be protected from submersion. Should the module become submerged, level readings may drift and the hydrophobic filter will seal to protect the reference air line. Note To protect the 2150EX AV Flow module and sensor, the hydrophobic filter seals off the reference air line when it is exposed to excessive moisture. When sealed, the filter prevents irreparable damage, yet may cause the level readings to drift. This single-use filter must be replaced once it becomes sealed. 2. Make sure all of the protective caps are in place. An unused upper communication connection must be capped to prevent damage and terminate the communication line. If the communication connector is in use, its cap should be properly stowed. Like the module and sensor connections, the protective caps and their O-rings should be cleaned and coated with a silicone lubricant. Damaged O-rings must be replaced (P/N 202-1006-69). 3. Carefully route cables. Protect them from traffic in the area. Avoid leaving excess AV Sensor cable in the flow stream where it may collect debris. 2.9.1 Program the Module After you have installed the AV Sensor in the flow stream, the flow stream properties must be defined. To do this, connect to the 2150EX with Flowlink software and define the stream properties in the 2150EX module’s program settings. These ensure that the system correctly reads the liquid level and converts the measured level to flow rate. 2-37
Page 1:
2150EX Area Velocity Flow Module In
Page 5 and 6:
2150EX Area Velocity Flow System Sa
Page 7 and 8:
Page 9 and 10:
Page 11 and 12: 2150EX Area Velocity Flow System Ta
Page 13 and 14: 2150EX Area Velocity Flow System Ta
Page 15 and 16: 2150EX Area Velocity Flow System Se
Page 61: 2150EX Area Velocity Flow System Se
Page 93 and 94: 2150EX Area Velocity Flow System Ap
Page 113 and 114:
2150EX Area Velocity Flow System Ap
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
2150EX Area Velocity Flow System In
Page 137:
DECLARATION OF CONFORMITY Applicati
Page 143 and 144:
DECLARATIONOFCONFORMITY Applic
Page 145 and 146:
DECLARATION OF CONFORMITY Applicati
Page 147:
Teledyne Isco One Year Limited Warr
show all

2150EX AV Flow Module - Isco

Create successful ePaper yourself

Delete template?

Save as template?