2150EX AV Flow Module - Isco

More documents

Recommendations

Info

2150EX Area Velocity Flow System Section 2 Preparation and Installation Figure 2-4 Assembling a basic portable system Connecting the Modules To connect the 2150EX and 2191EX/2196EX modules, refer to the following instructions and Figure 2-4. 1. On the top of the battery module, remove the cap and stow it on the holder. This exposes the communication connector. 2. Prepare the battery module’s communication connector: a. Inspect the connector. It should be clean and dry. Damaged O-rings must be replaced. Spare O-rings (P/N 202-1006-69) are supplied in the 2191EX maintenance kit (60-2009-332). b. Coat the O-ring’s sealing surface with a silicone lubricant. (A small quantity of lubricant is supplied in the maintenance kit.) CAUTION Do not use petroleum-based lubricants. Petroleum-based lubricants will cause the O-ring to swell and eventually deteriorate. Aerosol silicone lubricant sprays often use petroleum based propellants. If you are using an aerosol spray, allow a few minutes for the propellant to evaporate before proceeding. 3. Place the carrying handle on the battery module. (If you are stacking two 2150EX modules on top of the 2191EX/2196EX, position the handle between the 2150EX modules.) 2-10
2150EX Area Velocity Flow System Section 2 Preparation and Installation 4. Unlock the 2150EX module’s latch by pressing in on the latch release (right side). 5. Underneath the 2150EX, remove the cap from the lower communication connector and stow it in the holder. 6. Lock the latch. Locking the latch correctly seats and aligns the lower cap in its holder. 7. Position the 2150EX over the 2191EX/2196EX battery module. Align the connectors and lower the 2150EX onto the 2191EX/2196EX. 8. Unlock the 2150EX module’s latch by pressing in on the latch release (right side). 9. Firmly press the modules together and lock the 2150EX module’s latch (left side). The communications indicator will blink during the start-up routine to indicate the 2150EX is operating. Note Unused communication ports on the top and bottom of the stack must be capped. The connector caps terminate the communication lines and protect the pins. 2-11
Page 1: 2150EX Area Velocity Flow Module In
Page 5 and 6: 2150EX Area Velocity Flow System Sa
Page 11 and 12: 2150EX Area Velocity Flow System Ta
Page 13 and 14: 2150EX Area Velocity Flow System Ta
Page 15 and 16: 2150EX Area Velocity Flow System Se
Page 35: 2150EX Area Velocity Flow System Se
Page 87 and 88:
2150EX Area Velocity Flow System Se
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
2150EX Area Velocity Flow System Ap
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
2150EX Area Velocity Flow System In
Page 137:
DECLARATION OF CONFORMITY Applicati
Page 143 and 144:
DECLARATIONOFCONFORMITY Applic
Page 145 and 146:
DECLARATION OF CONFORMITY Applicati
Page 147:
Teledyne Isco One Year Limited Warr
show all

2150EX AV Flow Module - Isco

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?