2150EX AV Flow Module - Isco

More documents

Recommendations

Info

2150EX Area Velocity Flow System Section 1 Introduction Rollover Memory 1.2 Identifying Module Components Whether the measurements are stored at the primary or secondary rate, they are stored in a rollover type of memory. When full, the module overwrites the oldest data with the newest readings. The various components of the 2150EX are shown in Figures 1-1 through 1-4. Items referenced in the figures are described in Tables 1-1 through 1-4. Top View 2 3 1 Bottom View 4 5 6 7 Figure 1-1 2150EX - Top and Bottom Views Table 1-1 2150EX Area Velocity Flow Module - Top and Bottom Views Item No. Fig. 2-1 Name Description 1 Latch Latches the module in place. A latch release is located on the right side of the module. 2 Communication Connector (shown uncapped) 3 Connector Cap (shown on holder) 4 Desiccant Cartridge and Hydrophobic Filter Upper communication port; used to connect to another module, or to a PC running Flowlink software. Insert into unused communication connector to terminate the network and protect it from moisture damage. When the communication connector is in use, the cap must be stowed on its holder to protect the terminating components inside the cap. The cartridge holds desiccant that dries the reference air. The filter prevents moisture from entering the reference line. 5 Communication Indicator Illuminates when module communications are active. 6 Communication Connector (shown plugged) Used to connect the module to the 2191EX or 2196EX battery module, or to another 2150EX module. When the communication connector is in use, the plug must be stowed in its holder to protect the terminating components inside the cap. 7 Plug Holder Used to store the Connector Plug. 1-4
2150EX Area Velocity Flow System Section 1 Introduction 2 1 3 4 5 Figure 1-2 2150EX Connected to 2191EX- Top Right View Item No. Fig. 2-2 Table 1-2 2150EX Area Velocity Flow Module - Top Right View Name Description 1 Carrying Handle Used to lift and carry the unit. 2 Communication Connector (shown capped) Upper communication port, used to connect to another module or to a PC running Flowlink software. 3 Cap Holder Used to store the connector cap. 4 AV Sensor Receptacle Port used to attach the AV Sensor. Insert the protective cap when not in use. 5 2191EX Used to store battery packs and provide a source of power for the 2150EX. 1-5
Page 1: 2150EX Area Velocity Flow Module In
Page 5 and 6: 2150EX Area Velocity Flow System Sa
Page 11 and 12: 2150EX Area Velocity Flow System Ta
Page 13 and 14: 2150EX Area Velocity Flow System Ta
Page 15 and 16: 2150EX Area Velocity Flow System Se
Page 17: 2150EX Area Velocity Flow System Se
Page 69 and 70:
2150EX Area Velocity Flow System Se
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
2150EX Area Velocity Flow System Ap
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
2150EX Area Velocity Flow System In
Page 137:
DECLARATION OF CONFORMITY Applicati
Page 143 and 144:
DECLARATIONOFCONFORMITY Applic
Page 145 and 146:
DECLARATION OF CONFORMITY Applicati
Page 147:
Teledyne Isco One Year Limited Warr
show all

2150EX AV Flow Module - Isco

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?