IPL Migration Considerations for PM43 and PC Series ... - Intermec

More documents

Recommendations

Info

Supported Modes and Commands The modes and commands listed in this section are supported in the new implementation of IPL. Please refer to the IPL Command Reference Manual for syntax and usage. Supported Modes IPL Mode Advanced Mode Program Mode Print Mode Emulation Mode Legacy Mode Test and Service Mode Supported Commands IPL Syntax Definition IPL default mode. IPL mode to design bar code label formats. IPL mode to download data to the printer and print bar code labels. 10 mil for 100 dpi printhead Data Shift One Bit per Byte Font spacing Minimal Support: Enter command (T) Exit command (R) Factory Default command (D) Test labels commands (h, Q, s) Description ; Command Terminator C c D d E e F G g H I j k L M First Data Entry Field, Select Error code, Request Warm Boot Clear all data Next Data Entry Field, Select Clear Data From Current Field Reset Abort Print Job Status Enquiry Postamble, Set Start and Stop Codes (Code 39), Print Advanced Mode, Select Emulation Mode, Enter Field Decrement, Set Auto-Transmit 2, Enable Format, Select Auto-Transmit 3, Enable Field, Select Page, Select Direct Graphics Mode, Select Printhead Parameters, Transmit Field Increment, Set Auto-Transmit 1, Enable Auto-Transmit 1, 2, and 3, Disable Label and Gap Length, Transmit Program Number, Transmit IPL Syntax m N O P p Q q T u V v x .x y Description Memory Usage, Transmit Increment and Decrement, Disable Options Selected, Transmit Program Mode, Enter Configuration Parameters, Transmit Remaining Quantity and Batch Count, Transmit Date or Time, Transmit Test and Service Mode, Enter User-Defined Characters, Transmit (command format change) Battery Status and Information, Transmit Font, Transmit (command format change) Format, Transmit (command format change) Execute shell commands Page, Transmit (command format change) Print Form Feed Numeric Field Separator Alphanumeric Field Separator Command Terminator 2 Command Terminator 1 A Bs,DEV_NAME Bs,DISCOVER Bs,.PASSKEY Bs,RESERVE,n Bt Bt,AUTH Bt,DEV_ADDR Bt,DEV_NAME Bt,DISCOVER Bt,.PASSKEY Bt,RESERVE C c D d e F f h Quantity Count, Set Control Panel Access Permission, Set Device Name, Set Discoverable State, Set Passkey, Set Reserve Printer, Set All Bluetooth Settings, Transmit Authenticate, Transmit Device Address, Transmit Device Name, Transmit Descoverable State, Transmit Passkey, Transmit Reserve Printer, Transmit Emulation or Advanced Mode on Power-Up Cutter, Enable or Disable End-of-Print Skip Distance, Set. Default is ‘0’ regardless of media loaded Dark Adjust, Set Media Fault Recovery Mode, Set Top of form, Set Label Rest Point, Adjust Printhead Loading Mode, Select
IPL Syntax Description IPL Syntax Description L Maximum Label Length, Set wt,.EAP_USER EAP User Name, Transmit l Printer Language, Select wt,INNER_AUTH Inner Authentication, Transmit n o P q R r S T t V W ws,ACQUIRE_PAC ws,CA_CERT ws,CHANNEL ws,EAP_PASS ws,EAP_TYPE ws,.EAP_USER ws,INNER_AUTH ws,MODE ws,PAC ws,PWR_MODE ws,ROAM ws,.SERVER_CN1 ws,.SERVER_CN2 ws,SSID ws,TTLS_USER ws,VALIDATE ws,WEP1 ws,WEP2 ws,WEP3 ws,WEP4 ws,.WEP_KEY ws,WPA_PSK wt wt,ACQUIRE_PAC wt,AP_MAC wt,AUTH wt,CA_CERT wt,CHANNEL wt,EAP_PASS Setting Network Parameters in Manual Mode Direct Graphics Emulation Mode, Enable or Disable Communication Port Configuration, Set Date or Time, Set Label Retract, Enable or Disable Enable/ disable n=2 unsupported Label Retract Distance, Set Print Speed, Set Label Stock Type, Select Self-Strip, Enable or Disable Battery Low Voltage Threshold, Set Label Width, Set Acquire PAC, Set Certificate Authority, Set Active Channel, Set EAP Password, Set EAP Type, Set EAP User Name, Set Inner Authentication, Set Mode, Set Protected Access Credential, Set Power Management Mode, Set Roaming Bias, Set Server Common Name 1, Set Server Common Name 2, Set SSID (Network Name), Set TTLS User Name, Set Validate, Set WEP, Set WEP, Set WEP, Set WEP, Set WEP Key, Set WPA Pre-Shared Key, Set All settings, Transmit (Wireless LAN or 802.11x) Acquire PAC, Transmit Access Point Information, Transmit 802.11 Authentication, Transmit Certificate Authority, Transmit Active chaneel, Transmit EAP Password, Transmit wt,MODE wt,PAC wt,PWR_MODE wt,.REGION wt,ROAM wt,.SERVER_CN1 wt,.SERVER_CN2 wt,SIGNAL wt,SPEED wt,SSID wt,STATE wt,TTLS_USER wt,VALIDATE wt,WEP1 wt,WEP2 wt,WEP3 wt,WEP4 wt,.WEP_KEY wt,WPA_PSK X xu z A or F B b c c c D D d E e f f G H h Mode, Transmit Protected Access Credential, Transmit Power Management Mode, Transmit Region, Transmit Roaming Bias, Transmit Server Common Name 1, Transmit Server Common Name 2, Transmit Signal Strength, Transmit Speed, Transmit SSID (Network Name), Transmit State, Transmit TTLS User Name, Transmit Validate, Transmit WEP, Transmit WEP, Transmit WEP, Transmit WEP, Transmit WEP Key, Transmit WPA Pre-Shared Key, Transmit Label Origin, X-Y Adjust Change User Slash Zero, Enable or Disable Cut Preamble, Set Data Shift – International Characters Batch Count, Set Format, Create or Edit Bar Code Field, Create or Edit Border Around Human-Readable Text, Define Bar Code, Select Type Font Type, Select Graphic, Select Factory Defaults, Reset Field, Delete Field Data, Define Source Format, Erase Page Format Page Data Source, Define Field Direction, Define Formats, Print User-Defined Character, Clear or Create Human Readable Field, Create or Edit Hardware Configuration Label, Print wt,EAP_TYPE EAP Type, Transmit
Page 1 and 2: Technology Brief IPL Migration Cons
Page 3 and 4: Barcode Differences Pattern Differe
Page 5 and 6: UPC/EAN IPL barcode select command
Page 7: Unsupported Commands Most commands
Page 11 and 12: New Commands Wireless 802.11 Comman
Page 13 and 14: Legacy Command wt Legacy Command Pa
Page 15: Technical Support Should you experi

IPL Migration Considerations for PM43 and PC Series ... - Intermec

Create successful ePaper yourself

Delete template?

Save as template?