Minilyzer ML1 User Manual

More documents

Recommendations

Info

Introduction International Warranty and repair International Warranty NTi Audio guarantees the Minilyzer and its components against defects in material or workmanship for a period of one year from the date of original purchase, and agrees to repair or to replace at its discretion any defective unit at no cost for either parts or labor during this period. restrictions This warranty does not cover damages caused through accidents, misuse, lack of care, the attachment or installation of any components that were not provided with the product, loss of parts, connecting the instrument to a power supply, input signal voltage or connector type other than specified, or wrongly polarized batteries. In particular, no responsibility is granted for special, incidental or consequential damages. This warranty becomes void if servicing or repairs of the product are performed by any party other than an authorized NTi Audio service center or if the instrument has been opened in a manner other than specified in this manual. No other warranty, written or verbal, is authorized by NTi Audio. Except as otherwise stated in this warranty, NTi Audio makes no representation or warranty of any kind, expressed or implied in law or in fact, including, without limitation, merchandising or fitting for any particular purpose and assumes no liability, either in tort, strict liability, contract or warranty for products. repair of your Minilyzer Ml1 In case of malfunction, take - or ship prepaid - your NTi Audio Minilyzer packed in the original box, to the authorized NTi Audio representative in your country. For contact-details please see the NTi Audio web page: www.nti-audio.com Be sure to include a copy of your sales invoice as prove of purchase date. Transit damages are not covered by this warranty. 6
Warnings Introduction In order to avoid any problems during the operation of the instrument, follow the rules listed below: • Read this manual thoroughly before you operate the instrument for the first time. • Use the instrument for the intended purpose only. • Never connect the instrument to a high voltage output such as a power amplifier, mains power plug, etc. • Do not disassemble the instrument. • Never use the instrument in a damp environment. • Remove the batteries as soon as they are flat or if the instrument is not intended to be used for a longer period of time. 7
Page 1 and 2: Minilyzer ML1 User Manual
Page 3 and 4: TAble of CoNTeNTs: 1. In t r o d u
Page 5: egistration Register as a customer
Page 9 and 10: attery replacement Introduction Aft
Page 11 and 12: Power ON/OFF - Backlight The yellow
Page 13 and 14: Menu bar Basic Operation The menu b
Page 15 and 16: c. setup Basic Operation The setup
Page 17 and 18: Inputs and Monitor output On top of
Page 19 and 20: actual range or the up/down keys to
Page 21 and 22: Measurement Functions start of meas
Page 23 and 24: By exceeding the primary indicator
Page 25 and 26: c. Calibration Panel Measurement Fu
Page 27 and 28: THd+N Measurement Functions In this
Page 29 and 30: The following examples explain the
Page 31 and 32: An overrange indicator appears for
Page 33 and 34: sweep ML1 supports two sweep modes:
Page 35 and 36: . Time Sweep In the TIME SWEEP mode
Page 37 and 38: 1/3 rd Octave RMS The 1/3 rd OCTAVE
Page 39 and 40: Measurement Functions To enter the
Page 41 and 42: 4. INDUCTION LOOP MODE (OPTIONAL) T
Page 43 and 44: Calibration An induction loop recei
Page 45 and 46: fsweep Frequency Sweep recording; P
Page 47 and 48: 6. ACCessorIes Minispl The MiniSPL
Page 49 and 50: Technical Specification 7. TeCHNICA
Page 51 and 52: Technical Specification Technical D
Page 53: Menu bar Measurement display escape

Minilyzer ML1 User Manual

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?