EuroStar Titan Taurus Ploughing with pleasure - Regent

EuroStar Titan Taurus
Mounted ploughs
Semi-mounted ploughs
Ploughing
with pleasure

The mounted plough EuroStar combines the advantages of a standard plough with those of a variable.
With a 3-5 hole working width adjustment the EuroStar can be adapted fast and simple to the
different structures of soil.
In combination with the well-tried CX-central adjustment the name EuroStar stands for high
flexibility and effectiveness in soil cultivation.
Advantages of the
EuroStar plough
technology
‣ Plough frame made of
alloy steel, sectional tubes
with 10 mm thickness of
the square tubing on all
models.
‣ EuroStar 120 without
drill holes in the frame
‣ CX adjustment center with
simple plough adjustment
for easy pulling ploughing
‣ Guidance of the plough
legs on both sides cares
for high stability
‣ Working widths from
34- 55 cm simple
adjustable
Modern plough technology cares for
high efficiency in soil cultivation.

Simple adjusting
for easy
pulling ploughing
‣ Variable first furrow width
adjustment of the first body
with the C – spindle.
‣ Easy adaptation to
different tractor tracks.
‣ No change of the traction
point because of
parallel shift.
‣ The traction point
adjustment with the
X – spindle cares for a
free of side pull ploughing
‣ With the traction point
indicator an optimal and
easy adjustment
is secured.
(independent from the first
furrow width adjustment)
‣ Separate inclining angle
can be adjusted
independently on
both sides of the plough.
‣ Hydraulic frame turning
draw in ram
The perfect solution –
the CX adjustment center
C
X
Highest stability for
a longer lifetime.
EuroStar – bearing technology
Version beginning from
model EuroStar 300
Additional strengthening of the
frame in the area of borings
Thick spare tubing of the frame profile
all models 10 mm (alloy steel)
The bearing pin and the bush
(through the frame) care for highest stability.
Arresting pin for hole adjustment of
the working width outside of the frame.
Version EuroStar 120
Working width adjustment
and bearing pins are
outside of the frame.
Advantages of the
EuroStar bearing
technology
The bearing technology has
been taken over from the
Titan Vario models
and so also give to the
EuroStar models a
essentially longer durability.
‣ Only one frame boring
EuroStar 120, no single
frame boring
‣ Working width adjustment
is lying outside
of the frame
‣ Long spacing of bodies
and great working widths
possible also at the lighter
EuroStar models
‣ In the area of the frame
boring strengthening
plates care for a higher
stability.
‣ Each additional
drill hole in the
main frame
is a loss in stability

At the Regent Titan Variable the wanted working width can be
adjusted hydraulically during the drive from the tractor seat,
whereby the front furrow and the traction point can be adapted automatically.
At the same time all pre-tools, disc-coulters and the depth wheel can be adjusted automatically.
Exceptional
technology for
highest demands.
Advantages of the
Titan plough technology
‣ Hydraulic working width
adjustment per plough body.
‣ Optimal adaptation of the
working width for
different kinds of soil
and land.
‣ The right working width
for each furrow.
Small seed furrow up to
the broad autumn furrow.
‣ Simple ploughing of wedge
areas or obstacles.

Simple adjusting for
easy pulling ploughing
The perfect solution –
the CX adjustment center
Advantages of the
Titan bearing technology
‣ Infinitely variable first
furrow width adjustment
of the first body with the
C – spindle.
‣ Light adaptation to the
different tractor tracks.
‣ No change of the traction
point cause of the
parallel shift.
‣ The traction point
adjustment with the
X – spindle cares for an
ploughing free of side
pulling.
‣ The traction point
indicator secures an
optimal and light
adjustment (independent
from the first furrow width
adjustment)
C
X
Titan 120 / 140 / 170
Greasing bearing pin
Throughout bush with
grease channel
Thick frame profile
all models at least 10 mm
Grease chamber with connection
to the grease channell
Additional strengthening of the
frame in the area of borings
Advantages of the
Titan bearing
technology
‣ Greasing bearing pins,
and the throughout bush
secures a long durability.
‣ No additional drill holes
for the frame reinforcement
‣ Each additional drill hole
in the frame is a loss in
stability.
‣ Few but great dimensioned
links.
‣ The inclination angle is
adjustable independently
from both plough sides.
‣ On cutting width change
during the work the
traction point is adjusted
automatically.
(No creeping of the draft
link resp. of the upper link
to right or left)
Titan 160 / 180 / 200
‣ Ploughing free of side pull
On each working width
240 cm
128 cm
‣ Memory cylinder
Hydr. frame turning
draw in
(Recommendable
as of 5 furrows)

Draft link connectingstrap
turning work
‣ Highest stability by bearing
on both sides of the pin.
Highest stability for a long durability.
The bearing of the headstock – the heart
of each reversible plough
Movable mounting axle
‣ for curve ploughing
‣ Reduction of the
transport width
by chamfered position.
‣ recommended for
on-land version.
ON-land
Version
‣ During ploughing the tractor
drives outside of the furrow.
‣ The big area of the hydraulic
adjustment allows also
ploughing with normal tyres
in the furrow and ploughing
until the end of the field.
‣ Double acting turning ram
with automatic final position
locking valve.
‣ Mounting of the locking
valve at the side
(easy to maintain).
‣ Stable turning axle of
highest material quality.
‣ Turning axle not welded,
but pressed into the axle
bearing in cold state.
(ensures highest stability)
‣ Wide apart lying taper roller
bearing (high load capacity)
‣ Bearings are greased
centrally.
‣ Highest stability by
additional stiffening in the
interior of the headstock.
10 11

The proved technology of the mounted reversible ploughs (EuroStar, Titan) in connection with a
semi-mounted chassis. Because of this combination the simple adjusting technology
is held on the Taurus semi-mounted reversible ploughs also.
Extended acreage output by
the pro in agriculture.
‣ At ploughing from
6- up to 9-furrows
the track of the wheel
is almost entirely ploughed
by the last plough bodies.
Thereby an exact ploughing
to the end of the field
or ploughing to hindrances
is possible.
‣ As the transport wheel is
fitted fairly in front, less
space is needed when
turning at the end of the
field. Cutting width infinitely
variable from 33 up to 55 cm
per plough body.
‣ The required cutting width
is always hydraulically set
in connection with the 1st
plough body.
‣ At the same time all the
pre-cutting tools, like
skimmers and coulters, as
well as the transport wheel
are placed in the right
position.
12 13

Safety in function and stability
result in a high area performance.
‣ The semi-mounted plough
is turned over two great
dimensioned hydraulic rams
actuated and free of stroke.
‣ universal joint set far in the front
and an infinitely adaptation to the
width of the tractor enable a small
turning radius
‣ A strong headstock with
great dimensioned
universal joints
‣ infinite cutting width
adjustment of the first body
‣ No tollerance of the
traction point due to the
parallel shifting.
‣ The anlge of inclination is
adjustable independent of
both plough sides.
‣ infinite working depth
adjustment
14 15

Mechanic and hydraulic
non-stop stone safety device
for ploughing on stony soils.
non-stop
System
mechanic
System
hydraulic
The mechanic
stone safety device
‣ Simple adjustment of the
releasing pressure over
the check screw.
‣ Stone safety device
elements hanged in front
are pressed into the
bearing during ploughing
‣ The four supporting points
allow a knock free release,
and a quick and powerful
re-penetration of the body.
‣ Big clearance towards the
top and side-wards.
‣ Pre-working tools are
removed automatically
with the plough bodies.
Power at the share top in kg
(at middle spring pressure)
View of the power flow during the release
of the Regent mechanic
non-stop stone safety device
2800
2600
2400
2200
2000
1800
1600
1400
1200
1000
800
600
400
max. releasing pressure of the spring
Works adjustment
All plough models EuroStar / Titan / Taurus
can be equipped with the “non-stop system”
Additional advantages
of the hydraulic stone
safety device system
‣ Releasing pressure
adjustable from 50 bar up
to 180 bar from the tractor.
‣ Can be locked
on very hard grounds.
‣ The pressure can always
be checked from the tractor
by means of a monometer.
‣ Safety device element
can switch to all directions
(also angular).
‣ No side force on the
plough beams.
‣ Highest durability through
course of force to the
smallest resistance.
‣ Guidance of plough beam
on both sides –
high stability.
‣ The bow shape of the
plough beam brings a
favourable position of centre
of gravity
‣ Shearing screws serve for
an additional safety.
200
Hub height
0
16 0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 cm
17

Quality of material for highest demands
and for a longer lifetime
Through the use of recent base material (depending on the mouldboard) and the special hardening method
it was able to reach a relevant higher resistance in abrasion.
A total hardening enables an increase of the durability of 20 %. Hardness in abrasion zones and elastic concerning pushing
encumbrances - that‘s the new result of the new heat and material treatment of Regent.
The mouldboard
of Regent
The mouldboards are now
hardened all over the cross
section and reach the best
durabilities for the hardest use
through their special form.
Best quality for highest
demands
The slatted body
of Regent
The slatted bodies have a
breadth of 12 mm and are all
over hardened and so very
wear resistant.
Experience of many years in
development and production ensure
an easy pulling mouldboard.
Front parts of the
mouldboards
‣ Serially with carbide-plating
(for a significant higher durability)
18 19

DG 774
SN
S
DW-S
SW-S
SW-X
Universal share divided (series)
(option with armour plating)
Beak share for high stability
and long lifetime
self sharpening
(series)
Flat share for
extreme stony ground
Universal share with
reversible point, very good
with reversible point DWS
(option)
For hard and dry soils,
for extreme use with reversible
point SWS
(option)
For extreme use
with reversible great
point XWS
(option)
Disc-coulter
with locking disc
plain ø510, ø560, ø600 mm
notched ø510, ø560, ø600 mm
Disc-coulter
Springed
wide furrow cutter
Subsoil decompactor V 250 with
exchangeable spike
Guide plate
For stony and level soils.
(cost-favourable as alternative
for the skimmer)
Wing coulter can be used
instead of a disc coulter.
maize straw skimmer
for many crop residues
(straw, catch crop)
from light to heavy soils, very
universal use possible
skimmer AM
for crop residues
(stubble field, maize)
for sticky soils
skimmer F
for greenland
from light to heavy soils
skimmer BV 27
special skimmer for extreme
working depths and
for very dry soils (e.g. Italy)
Dual depth wheel steel
ø500 x 165 mm
or ø510 x 185 mm
Pendulum depth wheel
with middle console
with rubber tyre and hydr.
P-SG ø700 x 260 mm
P-SG ø700 x 300 mm
P-SG ø700 x 350 mm
Combi transport and
depth wheel on middle console
with rubber tyre and hydr.
K-SG ø700 x 260 mm
K-SG ø700 x 300 mm
K-SG ø700 x 350 mm
20 21
Regent plough body often copied never reached.
New
M4
WS 7
W 7
W 79
WS 9
SKL 5B
SKT 6
SK 6
SKK 6
SKT 65
Universal body
middle up to heavy soils
very good crumbling
working depth up to 35 cm
W4 (4-42, 4-46, 4-48)
very easy pulling
good wide track cleaning
for flat ploughing
whole turning of the earth beam
also with high speed
very good for steep slope
WS 7 (7-38, 7-40, 7-42)
W 7 (7-46)
long drawn out body shape
from middle to
heavy loamy soils
easy pulling
good furrow clearance
good crushing effect
good hillside suitability
W 79
WS 9
universal useable
humus substantial
heavy sticky and
loamy soils
very wide track cleaning
good for steep slope
SKL 5 / SKL 4
SKL 5B
extremely sticky soil
recommendable for great depth
good turning and crumbling effect
deliverable with plastic
mouldboard edge (SKK)
SKT 6 / SK 6 / SKK 6 / SKT 65
Perfection
into detail

Technical data
kg
The right plough
for each performance.
Shares / weight kg
Eurostar 3 4 5 6 7 8 9
Frame
dimension
mm
Spacing of
bodies
cm
Working
width
cm
E 120K 790 1000 100x120 88 30 | 33 | 37 | 42 77
Framework
height
cm
kW 51 59 66 74 81 88 96 103 110 118 125 132 140 147 154 162 169 177 184 191 199 206 213 221 228 221 228 250 257 265 272 280 287 294 302 309 316
HP 70 80 90 100 110 120 130 140 150 160 170 180 190 200 210 220 230 240 250 260 270 280 290 300 310 320 330 340 350 360 370 380 390 400 410 420 430
3-)))
4-)))) E 120
E 120 810 1030 100x120 100 34 | 38 | 43 | 49 80
3-)))
4-)))) E 120
E 300 870 1120 120x120 100 32 | 35 | 40 | 45 | 50 80
E 400 960 1230 1440 120x120 100 32 | 35 | 40 | 45 | 50 82
E 500 1310 1560 140x140 103 38 | 42 | 45 | 48 | 52 82
E 600 1515 1780 2045 180x140/120 100 37 | 41 | 45 | 48 | 52 82
E 700 1860 2120 180x140 103 39 | 43 | 47 | 51 | 53 82 86
non-stop
E 120K NS 1110 1380 100x120 88 32 | 35 | 39 | 44 | 48 77
E 120 NS 1140 1420 100x120 100 37 | 42 | 47 | 52 77 80
E 400K NS 1590 1918 120x120 88 34 | 37 | 40 | 43 | 46 | 49 78
E 400 NS 1608 1935 120x120 100 39 | 42 | 45 | 48 | 52 78
E 600 NS 1860 2280 2735 180x140/120 100 37 | 41 | 45 | 49 | 52 78 82
M 600 NS 2090 2550 150x150 91 | 95 | 99 | 103 41 | 43 | 45 | 46 78 82
Titan 3 4 5 6 7 8 9
T 114 960 140x120 104 33 - 51 82
T 120 1140 100x120 95 30 - 50 80
T 140 980 1300 1510 140x120 90 | 100 | 104 33 - 53 82
T 160 1110 1320 1760 160x120 100 | 106 33 - 54 82
T 168 1200 1530 180x120 117 36 - 55 80 86
T 170 1560 1830 160x120 103 33 - 53 81
T 180 1250 1700 1980 2360 180x140 100 | 106 | 113 33 - 54 | 36 - 58 82 86 90 93
T 200 1350 1810 2200 2600 200x150 100 | 106 | 117 33 - 54 | 36 - 58 83 86 92 95
non-stop
T 140K NS 1570 120x120 88 32 - 50 75 80
T 140 NS 1320 1700 2090 140x120 90 | 100 | 104 32 - 50 | 33 - 52 77 80
T 160 NS 1400 1800 2090 160x120 100 | 106 32 - 50 77 82
T 180 NS 1900 2300 2650 180x140 100 | 106 34 - 52 80 84
T 200 NS 1950 2350 2750 200x150 100 | 106 34 - 52 80 84
Taurus 3 4 5 6 7 8 9
T 180 3300 3710 180x140 100 34 - 53 82
6-)))))) T 200 NS
3-))) 4-))))
5-))))) E 400
4-))))
5-))))) E 500
4-))))
5-)))))
6-)))))) E 600
5-)))))
6-)))))) E 700
3-))) 4-)))) E 120K NS
3-))) 4-)))) E 120 NS
4-))))
5-))))) E 400K NS
4-))))
5-))))) E 400 NS
4-))))
5-)))))
6-)))))) E 600 NS
5-)))))
6-)))))) M 600 NS
kW 51 59 66 74 81 88 96 103 110 118 125 132 140 147 154 162 169 177 184 191 199 206 213 221 228 221 228 250 257 265 272 280 287 294 302 309 316
HP 70 80 90 100 110 120 130 140 150 160 170 180 190 200 210 220 230 240 250 260 270 280 290 300 310 320 330 340 350 360 370 380 390 400 410 420 430
3-))) T 114
4-)))) T 120
3-)))
4-))))
5-))))) T 140
3-)))
4-))))
5-))))) T 160
3-)))
4-)))) T 168
4-))))
5-))))) T 170
3-)))
4-))))
5-)))))
6-)))))) T 180
3-))) 4-))))
5-)))))
6-)))))) T 200
4-)))) T140 NS
3-))) 4-))))
5-))))) T 140 NS
3-)))
4-))))
5-))))) T 160 NS
4-))))
5-)))))
6-)))))) T 180 NS
4-))))
5-)))))
3-))) 4-)))) E 300
kW 51 59 66 74 81 88 96 103 110 118 125 132 140 147 154 162 169 177 184 191 199 206 213 221 228 221 228 250 257 265 272 280 287 294 302 309 316
HP 70 80 90 100 110 120 130 140 150 160 170 180 190 200 210 220 230 240 250 260 270 280 290 300 310 320 330 340 350 360 370 380 390 400 410 420 430
6-))))))
7-))))))) T 180
Types and power
requirement tab
T 200 3250 3520 3850 4230 4650 200x150 100 | 106 | 117 34 - 55 | 36 - 55 80 85 87 91 95
non-stop
5-)))))
6-))))))
7-)))))))
8-))))))))
9-))))))))) T 200
22
T 200 NS 3950 4350 4750 5200 200x150 100 | 106 33 - 50 | 33 - 52 80 84
Approximate weight in kg – depending on plough body and spacing of bodies without additional equipment.
Subject to technical changes and misprints.
6-))))))
7-)))))))
8-))))))))
9-))))))))) Taurus 200 NS
23

Expertise in soil
cultivation
Sales partner
www.regent.at
Regent Pflugfabrik GmbH
Bahnhofstr. 105
A-4800 Attnang-Puchheim
Tel. +43 (0) 76 74 / 626 61
Fax. +43 (0) 76 74 / 622 07
export@regent.at
4890/0313 En 4579