Operators and Installation Manual RA-2500 AIS Receiver.pdf - Jotron

More documents

Recommendations

Info

6. Junction Box Connector See chapter 7.2 7. Programming Connector This 15 pin D-sub connector is for programming of the Receiver by Program Engineers only. 8. Extra I/O Connector This 9 pin D-sub connector is not described. Factory use only. 7.2 Description of Junction Box Connector 37 Pin D-sub RA-2500 Functions Input / Output 13 AIS TD4-B (External Out Display) 14 AIS TD4-A (External Out Display) Isolated GND 15 AIS RD4-B In 16 AIS RD4-A In Isolated GND 17 AIS TD5-B 18 AIS TD5-A Isolated GND 19 AIS RD5-B 20 AIS RD5-A Isolated GND 21 AIS TD6-B Out 22 AIS TD6-A Out Isolated GND 23 AIS RD6-B In 24 AIS RD6-A In Isolated GND 25 AIS TD7-B Reserved 26 AIS TD7-A Reserved Isolated GND 27 AIS RD7-B 28 AIS RD7-A Isolated GND 29 RS-232 TX Out 30 RS-232 RX In 31 Dry relay contact, Referred to pin 48 Alarm Out (NC) 32 Dry relay contact, Referred to pin 48 Alarm Out (NO) 33 Dry relay contact, Referred to Common #46 & 47 34 I/O Spare 35 Future warning for Backup Power 36 GND 82694_Op&Ins MAN_RA2500_D 7-2
7.3 Description of 24VDC connection to receiver 24VDC Connector for cable, front side GND + 24VDC 0VDC 7.4 Description of LAN connector Contains Ethernet 10Mbit Twisted pair interface and RS232 serial port with Tx and Rx. Service connector, 9 pins Dsub: Nr. Name Function In/Out 1 Ether_Tx+ Ethernet Transceive Data+ Out 2 Ether_Tx- Ethernet Transceive Data- Out 3 Ether_Rx+ Ethernet Receive Data+ In 4 Ether_Rx- Ethernet Receive Data- In 5 GND Ground - 6 7 8 +14V +14 V, max 300mA. - 9 NC Not Connected - 82694_Op&Ins MAN_RA2500_D 7-3
Page 1 and 2: 82693_Op&Ins MAN_TR2500_D 1
Page 3 and 4: COG See COURSE OVER GROUND COURSE O
Page 5 and 6: MMI Man Machine Interface NMEA Nati
Page 7 and 8: Amendment Record AMENDMENT NO. INCO
Page 9 and 10: LIST OF CONTENTS 1 GENERAL ........
Page 11 and 12: 1 GENERAL 1.1 Features The RA-2500
Page 13 and 14: 1.3 System overview The system is b
Page 15 and 16: RECEIVER Sensitivity TR-2500 RECEIV
Page 17 and 18: 3.2 Using Ethernet interface Using
Page 19 and 20: 4 INSTALLATION Important notice In
Page 21 and 22: Vertical separation distance and di
Page 23 and 24: 4.3 Receiver unit When selecting a
Page 25 and 26: 4.3.3 Bracket mounting hole measure
Page 27 and 28: 5 OPERATION Figure 5.0, Front view
Page 29 and 30: 5.3 Connecting power After connecti
Page 31 and 32: 5.3.1.2 Selection of IP address Be
Page 33 and 34: Menu: Current Senso 1/5 LAT: --- LO
Page 35 and 36: Select “SW Version” menu by pre
Page 37 and 38: Source: Surveyed ↑=Inte The Surve
Page 39 and 40: 5.5 Description of sentence format
Page 41 and 42: 5.6.3 Format BCF: Configure RA-2500
Page 43 and 44: 5.7.3 ALR - Set alarm state. Local
Page 45 and 46: 5.7.6 GGA Global positioning system
Page 47: 7 WIRING AND CONNECTIONS 7.1 RA-250
Page 51 and 52: 9 LIST OF VHF CHANNELS Channel no.
Page 53 and 54: 10.2 Procom CXL 2-1/l Maritime VHF
Page 55 and 56: 10.4 BNC connector 95299, Suhner 24
Page 57 and 58: 10.8 N Connector Male 80581, Suhner
Page 59: 82694_Op&Ins MAN_RA2500_D 11-2

Operators and Installation Manual RA-2500 AIS Receiver.pdf - Jotron

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?