Operators and Installation Manual RA-2500 AIS Receiver.pdf - Jotron

More documents

Recommendations

Info

5.2 Menus 5.2.1 Menu Flowchart Rng Brg Name: 1/6 1384 124 NIKITA 1754 124 COLOR FESTIV 99.1 098 PETER VESSEL Esc Menu Enter key 1 to 4 Main Menu 1/4 1 Current Sensors 2 Internal GPS 3 Diagnostic 4 Config Esc Enter NIKITA 1/14 MMSI: 444 Call: ETA: ----:0000 Dest: VIKSFJORD Enter Type:0 Lat: N58d52.58 Lon: E010d45.51 SOG: 10.0 KT COG: 3.2 Head: 45 Length: --- Beam:--- Draught: Nav.Stat Esc Esc Menu: Current Senso 1/5 LAT: N 5903.21 LON: E 01007.44 Pos Accur.: Low Pos Source: Internal HH:MM:SS DD/MM/YYYY Menu: Internal GPS 1/4 LAT: --- LON:--- Status: NoFix DD.MM.YY HH:MM:SS How to navigate in the menus/submenus If there is a number in front of the menu/submenu, you can select it directly by pressing the numeric key with the corresponding number. When no number is present in front of a submenu, use the arrow up/down keys ↓ to choose and press [Enter] key to select. The [Esc] key takes you one step back. Esc Esc Menu: Diagnostic 1/6 1 BIIT 2 Alarm 3 System Indicators 4 History 5 SW Versions 6 Service Menu: Config 1/4 1 Recv. Channels 2 Position Source 3 I/O Ports 4 Buzzer 82694_Op&Ins MAN_RA2500_D 5-2
5.3 Connecting power After connecting the antennas and Inputs/Outputs, the DC power can be connected to the RA-2500. The input voltage must be within 24VDC +30% / -10%. The power consumption is 17W. At start, the RA-2500 will look for connected sensors and equipment for 20 –30 seconds. The display will show: Loading … Please wait After a while the alarm status will be indicated. Press [Del] key to reset the alarm settings. If the RA-2500 has been previous configured, and the configuration is OK, there is no need to go further in this chapter. Otherwise continue with chapter 9.2.1. 5.3.1 LAN configuration Press [Menu] key to enter “Main menu”. Main Menu 1/4 1 Current Sensors 2 Internal GPS 3 Diagnostic 4 Config Showing the number of sub-menus available below the selected menu Select “Config” by [arrow down] key. Press [Enter] key. 82694_Op&Ins MAN_RA2500_D 5-3
Page 1 and 2: 82693_Op&Ins MAN_TR2500_D 1
Page 3 and 4: COG See COURSE OVER GROUND COURSE O
Page 5 and 6: MMI Man Machine Interface NMEA Nati
Page 7 and 8: Amendment Record AMENDMENT NO. INCO
Page 9 and 10: LIST OF CONTENTS 1 GENERAL ........
Page 11 and 12: 1 GENERAL 1.1 Features The RA-2500
Page 13 and 14: 1.3 System overview The system is b
Page 15 and 16: RECEIVER Sensitivity TR-2500 RECEIV
Page 17 and 18: 3.2 Using Ethernet interface Using
Page 19 and 20: 4 INSTALLATION Important notice In
Page 21 and 22: Vertical separation distance and di
Page 23 and 24: 4.3 Receiver unit When selecting a
Page 25 and 26: 4.3.3 Bracket mounting hole measure
Page 27: 5 OPERATION Figure 5.0, Front view
Page 31 and 32: 5.3.1.2 Selection of IP address Be
Page 33 and 34: Menu: Current Senso 1/5 LAT: --- LO
Page 35 and 36: Select “SW Version” menu by pre
Page 37 and 38: Source: Surveyed ↑=Inte The Surve
Page 39 and 40: 5.5 Description of sentence format
Page 41 and 42: 5.6.3 Format BCF: Configure RA-2500
Page 43 and 44: 5.7.3 ALR - Set alarm state. Local
Page 45 and 46: 5.7.6 GGA Global positioning system
Page 47 and 48: 7 WIRING AND CONNECTIONS 7.1 RA-250
Page 49 and 50: 7.3 Description of 24VDC connection
Page 51 and 52: 9 LIST OF VHF CHANNELS Channel no.
Page 53 and 54: 10.2 Procom CXL 2-1/l Maritime VHF
Page 55 and 56: 10.4 BNC connector 95299, Suhner 24
Page 57 and 58: 10.8 N Connector Male 80581, Suhner
Page 59: 82694_Op&Ins MAN_RA2500_D 11-2

Operators and Installation Manual RA-2500 AIS Receiver.pdf - Jotron

Create successful ePaper yourself

Delete template?

Save as template?