CLIOwin 6.5 PCI User's Manual - Audiomatica Srl

More documents

Recommendations

Info

9.2.1 TOOLBAR BUTTONS Starts an FFT or RTA measurement. Pressing the drop down menu it is possible to select the Continue switch. In this mode the measurements is not started from blank but accumulates with the previously stopped one; see Averaging (9.6) for details. Stops the current measurement. Selects Internal Trigger operation. When pressed the acquisition is triggered by the generated signal. Activates the Time Data display. Enables the Hold function. Depending on the setting entered in the FFT Settings dialog box, it is possible to hold either the minimum or maximum value per frequency point. Enters the FFT Settings dialog box. 9.2.2 TOOLBAR DROP DOWN LISTS AND DISPLAY data window Selects a weighting data window among the following: - Rectangular (no window) - Hanning - Hamming - Blackman - Bartlett (triangular) - FlatTop channel display Selects the input channel or function to display. Y scale units Selects the measurement units. target averages Inputs the total number of averages. Averaging is controlled by the setting in the FFT Settings dialog; see Averaging (9.6) for details. number of averages display Displays the number of the actual average; this number increases during the measurement unless, while in exponential averaging, the target has already been reached; see Averaging (9.6) for details. 78 Chapter 9 - FFT
9.3 FFT SETTINGS DIALOG Fig. 9.2 The FFT settings dialog box FFT Size Selects the number of samples acquired and processed by each FFT. It is possible to choose a size between 256 and 65536 points. Sampling Selects the sampling frequency. Hold Function Selects either Min or Max hold function. This functionality is activated by the relative toolbar button. Freq Axis Selects among four possible FFT or RTA operating modes: - Linear frequency axis (narrowband) - Logarithmic frequency axis (narrowband) - 1/3 Octave filtered (RTA) - 1/6 Octave filtered (RTA) Delay Permits the input of the desired processing delay (in ms) when in Internal Trigger mode. See 9.7 for details. Averaging Selects either linear or logarithmic averaging; see Averaging (9.6) for details. Chapter 9 - FFT 79
Page 1 and 2:
ELECTRICAL & ACOUSTICAL TESTS User'
Page 3 and 4:
CONTENTS 1 INTRODUCTION ...........
Page 5 and 6:
8.5.1 MEASURING AN INDUCTOR .......
Page 9:
1 INTRODUCTION 1.1 ABOUT THIS MANUA
Page 12 and 13:
12 Chapter 1 - Introduction
Page 14 and 15:
2.1 THE PB-4281 PC BOARD AND SC-01
Page 16 and 17:
2.2.3 THE MIC-01 (OR MIC-02) FREQUE
Page 18 and 19:
2.4 THE QCBOX MODEL 4 AMPLIFIER & S
Page 20 and 21:
Figure 3.1 2) 2 x Stereo mini jack
Page 22 and 23:
3.3 HARDWARE REGISTRATION WITH WIND
Page 24 and 25:
3.3.2 HARDWARE REGISTRATION UNDER W
Page 26 and 27:
3.3.3 HARDWARE REGISTRATION UNDER W
Page 28 and 29: Figure 3.21 Let's now verify that t
Page 30 and 31: 3.4 SOFTWARE INSTALLATION This para
Page 32 and 33: 3.6 RUNNING CLIOWIN FOR THE FIRST T
Page 34 and 35: 3.7.1 CALIBRATION VALIDATION Figure
Page 36 and 37: 36 Chapter 3 - Installation
Page 38 and 39: 38 Chapter 4 - Troubleshooting CLIO
Page 40 and 41: 5.3 CLIOWIN DESKTOP The CLIOwin des
Page 42 and 43: It is possible to generate the foll
Page 44 and 45: Fig.5.5 Microphone sensitivity dial
Page 46 and 47: 5.5.2 CONTROLLING A TURNTABLE Fig.5
Page 48 and 49: 5.6.2 ANALYSIS MENU The Analysis me
Page 50 and 51: H Enables the Hold function. Equiva
Page 52 and 53: CTRL+P Swithces on and off the micr
Page 54 and 55: 5.7.2 CONNECTING A MICROPHONE For a
Page 56 and 57: 56 Chapter 5 - CLIOwin basics
Page 58 and 59: When you find a CLIOwin data file i
Page 60 and 61: Enters the Notes dialog where it is
Page 62 and 63: 6.3.5 CALIBRATION File > Calibratio
Page 64 and 65: 6.3.7 STARTUP OPTIONS AND GLOBAL SE
Page 66 and 67: 7.3 BUTTONS AND CHECKBOXES Moves (s
Page 68 and 69: 7.6 THE MLS TIME DOMAIN DISPLAY Whe
Page 70 and 71: 8.2.1 TOOLBAR BUTTONS Starts the me
Page 72 and 73: This operating mode is very useful;
Page 74 and 75: Figure 8.7 With the Multi-meter run
Page 76 and 77: 76 Chapter 8 - Multi-Meter
Page 80 and 81: 9.4 FFT AND RTA OPERATION The FFT a
Page 82 and 83: 9.5 AVERAGING Averaging plays a ver
Page 84 and 85: 9.6 TIME DATA DISPLAY (OSCILLOSCOPE
Page 86 and 87: 10.2.1 TOOLBAR BUTTONS Starts an ML
Page 88 and 89: 10.2.4 MLS POST-PROCESSING TOOLS Lo
Page 90 and 91: 10.4 MEASURING FREQUENCY RESPONSE I
Page 92 and 93: 150.0 CLIO 180.0 150.0 CLIO 180.0 O
Page 94 and 95: MLS Menu, select dBSPL as Y scale u
Page 96 and 97: 10.4.4 PHASE & GROUP DELAY We used
Page 98 and 99: 110.0 CLIO 7.50 dBSPL ms 100.0 6.00
Page 100 and 101: 10.5 OTHER TIME DOMAIN INFORMATION
Page 102 and 103: utton. Any process you execute can
Page 104 and 105: 104 Chapter 10 - MLS
Page 106 and 107: 11.2.1 TOOLBAR BUTTONS Starts the s
Page 108 and 109: Stepped is also not checked. Typica
Page 110 and 111: 11.3 A BRIEF DESCRIPTION ON SETTING
Page 112 and 113: 11.3.3 GATING Enabling Gating allow
Page 114 and 115: 11.4 DISTORTION AND SETTINGS Sinuso
Page 116 and 117: Finally Fig.11.12 shows the distort
Page 118 and 119: 12.3 WATERFALL BASICS Figure 12.2 W
Page 120 and 121: 12.4 MAKING A CUMULATIVE SPECTRAL D
Page 122 and 123: Let's now change the CSD aspect aga
Page 124 and 125: Figure 12.11 12.5.3 TAKING THE MEAS
Page 126 and 127: Figure 12.17 The final result for o
Page 128 and 129:
If you are novice in using CLIO or
Page 130 and 131:
-10.0 CLIO dBV -30.0 -50.0 -70.0 -9
Page 132 and 133:
13.4 I SENSE Requires Audiomatica C
Page 134 and 135:
Figure 13.12 Lets proceed now with
Page 136 and 137:
The figure shows us we are going to
Page 138 and 139:
13.7 THIELE & SMALL PARAMETERS 13.7
Page 140 and 141:
L 1kHz L 10kHz Inductance at 10kHz
Page 142 and 143:
Now we can save our complete result
Page 144:
[19] M.O. Hawksford, “Digital Sig
show all

CLIOwin 6.5 PCI User's Manual - Audiomatica Srl

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?