User Manual

More documents

Recommendations

Info

7 - 4 3200 <strong>User</strong>’s Guide
8 Utilities To Add a Test Code I.D. Prefix to All Symbologies This selection allows you to turn on transmission of a Code I.D. before the decoded symbology. (See the Symbology Chart, included in the Appendix A, page A-1) for the single character code that identifies each symbology.) This action first clears all current prefixes, then programs a Code I.D. prefix for all symbologies. This is a temporary setting that will be removed when the unit is power cycled. Show Software Revision Add Code I.D. Prefix to All Symbologies (Temporary) Scan the barcode below to output the current software revision, unit serial number, and other product information. Show Revision Show Data Format Scan the barcode below to show current data format settings. Data Format Settings Resetting the Standard Product Defaults If you aren’t sure what programming options are in your imager, or you’ve changed some options and want the standard product default settings restored, scan the Standard Product Default Settings barcode below. Standard Product Default Settings The Menu Commands starting on page 9-1 lists the standard product default settings for each of the commands (indicated by an asterisk (*) on the programming pages). 3200 <strong>User</strong>’s Guide 8 - 1
Page 1 and 2:
User’s Guide 3200 Linear Imager
Page 3 and 4:
Table of Contents Chapter 1 - Getti
Page 5 and 6:
Interleaved 2 of 5 ................
Page 7:
Chapter 10 - Product Specifications
Page 11 and 12:
1 Getting Started About This Manual
Page 13 and 14:
Plug and Play Plug and Play barcode
Page 15 and 16:
Note: For the imager to work proper
Page 17 and 18: 2 Terminal Interfaces Terminal ID I
Page 19 and 20: Keyboard Country Scan the appropria
Page 21 and 22: Control + ASCII Mode On: The imager
Page 23 and 24: RS-232 Word Length: Data Bits, Stop
Page 25 and 26: 3 Output Good Read Indicators Beepe
Page 27 and 28: 4 Data Editing Prefix/Suffix Overvi
Page 29 and 30: To Clear One or All Prefixes or Suf
Page 31 and 32: Intercharacter Delay An intercharac
Page 33 and 34: 5 Data Formatting Data Format Edito
Page 35 and 36: Move Commands F5 Move the cursor ah
Page 37 and 38: 6 Symbologies Introduction This pro
Page 39 and 40: No Check Character indicates that t
Page 41 and 42: Code 39 Check Character No Check Ch
Page 43 and 44: Code 39 Code Page Code pages define
Page 45 and 46: Code 93 < Default All Code 93 Setti
Page 47 and 48: Straight 2 of 5 IATA On * Off Strai
Page 49 and 50: Code 11 Message Length Scan the bar
Page 51 and 52: Telepen On * Off Telepen Output Usi
Page 53 and 54: This selection adds 2 or 5 digits t
Page 55 and 56: UPC E0 and UPC E1 Addenda Required
Page 61 and 62: MSI Message Length Scan the barcode
Page 63 and 64: RSS Expanded * On Off RSS Expanded
Page 65 and 66: 7 Interface Keys Keyboard Function
Page 67: Supported Interface Keys IBM AT/XT
Page 71 and 72: 9 Default Chart Resetting the Stand
Page 73 and 74: Selection Beeper Volume - Good Read
Page 75 and 76: Selection Interleaved 2 of 5 Check
Page 77 and 78: Selection UPC A Addenda Required UP
Page 79 and 80: Selection RSS Limited RSS Expanded
Page 81 and 82: 10 Product Specifications 3200 Prod
Page 83 and 84: Standard Cable Pinouts Serial Outpu
Page 85 and 86: 11 Maintenance Repairs Repairs and/
Page 87 and 88: Is the scanner having trouble readi
Page 89 and 90: 12 Customer Support Technical Assis
Page 91 and 92: Japan Telephone: +813-5770-6312 Fax
Page 93 and 94: Appendix A Symbology Chart Symbolog
Page 95 and 96: Dec Hex Char Dec Hex Char Dec Hex C
Page 97 and 98: UPC A Sample Symbols 0 123456 7890
Page 99 and 100: Programming Chart 0 1 2 3 4 5 6 7 8
show all

User Manual

Create successful ePaper yourself

Delete template?

Save as template?