User Manual
User Manual User Manual
UPC E UPC E0 and UPC E1 Most U.P.C. barcodes lead with the 0 number system. For these codes, use the UPC E0 selection. If you need to read codes that lead with the 1 number system, use the UPC E1 selection. Default = On (UPC E0) and Off (UPC E1). * UPC E0 On UPC E0 Off UPC E1 On * UPC E1 Off UPC E0 and UPC E1 Expand UPC E Expand expands the UPC E code to the 12 digit, UPC A format. Default = Off. On * Off 6 - 18 3200 User’s Guide
UPC E0 and UPC E1 Addenda Required When Addenda Required is set to on, the imager will only read UPC E barcodes that have addenda. Default = Not Required. Required UPC E0 Check Digit * Not Required Check Digit specifies whether the check digit should be transmitted at the end of the scanned data or not. Default = On. * On Off UPC E0 Number System The numeric system digit of a U.P.C. symbol is normally transmitted at the beginning of the scanned data, but the unit can be programmed so it will not transmit it. Default = On. * On Off 3200 User’s Guide 6 - 19
- Page 3 and 4: Table of Contents Chapter 1 - Getti
- Page 5 and 6: Interleaved 2 of 5 ................
- Page 7: Chapter 10 - Product Specifications
- Page 11 and 12: 1 Getting Started About This Manual
- Page 13 and 14: Plug and Play Plug and Play barcode
- Page 15 and 16: Note: For the imager to work proper
- Page 17 and 18: 2 Terminal Interfaces Terminal ID I
- Page 19 and 20: Keyboard Country Scan the appropria
- Page 21 and 22: Control + ASCII Mode On: The imager
- Page 23 and 24: RS-232 Word Length: Data Bits, Stop
- Page 25 and 26: 3 Output Good Read Indicators Beepe
- Page 27 and 28: 4 Data Editing Prefix/Suffix Overvi
- Page 29 and 30: To Clear One or All Prefixes or Suf
- Page 31 and 32: Intercharacter Delay An intercharac
- Page 33 and 34: 5 Data Formatting Data Format Edito
- Page 35 and 36: Move Commands F5 Move the cursor ah
- Page 37 and 38: 6 Symbologies Introduction This pro
- Page 39 and 40: No Check Character indicates that t
- Page 41 and 42: Code 39 Check Character No Check Ch
- Page 43 and 44: Code 39 Code Page Code pages define
- Page 45 and 46: Code 93 < Default All Code 93 Setti
- Page 47 and 48: Straight 2 of 5 IATA On * Off Strai
- Page 49 and 50: Code 11 Message Length Scan the bar
- Page 51 and 52: Telepen On * Off Telepen Output Usi
- Page 53: This selection adds 2 or 5 digits t
- Page 57 and 58: This selection adds 2 or 5 digits t
- Page 59 and 60: This selection adds 2 or 5 digits t
- Page 61 and 62: MSI Message Length Scan the barcode
- Page 63 and 64: RSS Expanded * On Off RSS Expanded
- Page 65 and 66: 7 Interface Keys Keyboard Function
- Page 67 and 68: Supported Interface Keys IBM AT/XT
- Page 69 and 70: 8 Utilities To Add a Test Code I.D.
- Page 71 and 72: 9 Default Chart Resetting the Stand
- Page 73 and 74: Selection Beeper Volume - Good Read
- Page 75 and 76: Selection Interleaved 2 of 5 Check
- Page 77 and 78: Selection UPC A Addenda Required UP
- Page 79 and 80: Selection RSS Limited RSS Expanded
- Page 81 and 82: 10 Product Specifications 3200 Prod
- Page 83 and 84: Standard Cable Pinouts Serial Outpu
- Page 85 and 86: 11 Maintenance Repairs Repairs and/
- Page 87 and 88: Is the scanner having trouble readi
- Page 89 and 90: 12 Customer Support Technical Assis
- Page 91 and 92: Japan Telephone: +813-5770-6312 Fax
- Page 93 and 94: Appendix A Symbology Chart Symbolog
- Page 95 and 96: Dec Hex Char Dec Hex Char Dec Hex C
- Page 97 and 98: UPC A Sample Symbols 0 123456 7890
- Page 99 and 100: Programming Chart 0 1 2 3 4 5 6 7 8
UPC E0 and UPC E1 Addenda Required<br />
When Addenda Required is set to on, the imager will only read UPC E barcodes<br />
that have addenda. Default = Not Required.<br />
Required<br />
UPC E0 Check Digit<br />
* Not Required<br />
Check Digit specifies whether the check digit should be transmitted at the end of<br />
the scanned data or not. Default = On.<br />
* On<br />
Off<br />
UPC E0 Number System<br />
The numeric system digit of a U.P.C. symbol is normally transmitted at the<br />
beginning of the scanned data, but the unit can be programmed so it will not<br />
transmit it. Default = On.<br />
* On<br />
Off<br />
3200 <strong>User</strong>’s Guide 6 - 19