User Manual

More documents

Recommendations

Info

UPC E UPC E0 and UPC E1 Most U.P.C. barcodes lead with the 0 number system. For these codes, use the UPC E0 selection. If you need to read codes that lead with the 1 number system, use the UPC E1 selection. Default = On (UPC E0) and Off (UPC E1). * UPC E0 On UPC E0 Off UPC E1 On * UPC E1 Off UPC E0 and UPC E1 Expand UPC E Expand expands the UPC E code to the 12 digit, UPC A format. Default = Off. On * Off 6 - 18 3200 <strong>User</strong>’s Guide
UPC E0 and UPC E1 Addenda Required When Addenda Required is set to on, the imager will only read UPC E barcodes that have addenda. Default = Not Required. Required UPC E0 Check Digit * Not Required Check Digit specifies whether the check digit should be transmitted at the end of the scanned data or not. Default = On. * On Off UPC E0 Number System The numeric system digit of a U.P.C. symbol is normally transmitted at the beginning of the scanned data, but the unit can be programmed so it will not transmit it. Default = On. * On Off 3200 <strong>User</strong>’s Guide 6 - 19
Page 1 and 2:
User’s Guide 3200 Linear Imager
Page 3 and 4: Table of Contents Chapter 1 - Getti
Page 5 and 6: Interleaved 2 of 5 ................
Page 7: Chapter 10 - Product Specifications
Page 11 and 12: 1 Getting Started About This Manual
Page 13 and 14: Plug and Play Plug and Play barcode
Page 15 and 16: Note: For the imager to work proper
Page 17 and 18: 2 Terminal Interfaces Terminal ID I
Page 19 and 20: Keyboard Country Scan the appropria
Page 21 and 22: Control + ASCII Mode On: The imager
Page 23 and 24: RS-232 Word Length: Data Bits, Stop
Page 25 and 26: 3 Output Good Read Indicators Beepe
Page 27 and 28: 4 Data Editing Prefix/Suffix Overvi
Page 29 and 30: To Clear One or All Prefixes or Suf
Page 31 and 32: Intercharacter Delay An intercharac
Page 33 and 34: 5 Data Formatting Data Format Edito
Page 35 and 36: Move Commands F5 Move the cursor ah
Page 37 and 38: 6 Symbologies Introduction This pro
Page 39 and 40: No Check Character indicates that t
Page 41 and 42: Code 39 Check Character No Check Ch
Page 43 and 44: Code 39 Code Page Code pages define
Page 45 and 46: Code 93 < Default All Code 93 Setti
Page 47 and 48: Straight 2 of 5 IATA On * Off Strai
Page 49 and 50: Code 11 Message Length Scan the bar
Page 51 and 52: Telepen On * Off Telepen Output Usi
Page 53: This selection adds 2 or 5 digits t
Page 57 and 58: This selection adds 2 or 5 digits t
Page 59 and 60: This selection adds 2 or 5 digits t
Page 61 and 62: MSI Message Length Scan the barcode
Page 63 and 64: RSS Expanded * On Off RSS Expanded
Page 65 and 66: 7 Interface Keys Keyboard Function
Page 67 and 68: Supported Interface Keys IBM AT/XT
Page 69 and 70: 8 Utilities To Add a Test Code I.D.
Page 71 and 72: 9 Default Chart Resetting the Stand
Page 73 and 74: Selection Beeper Volume - Good Read
Page 75 and 76: Selection Interleaved 2 of 5 Check
Page 77 and 78: Selection UPC A Addenda Required UP
Page 79 and 80: Selection RSS Limited RSS Expanded
Page 81 and 82: 10 Product Specifications 3200 Prod
Page 83 and 84: Standard Cable Pinouts Serial Outpu
Page 85 and 86: 11 Maintenance Repairs Repairs and/
Page 87 and 88: Is the scanner having trouble readi
Page 89 and 90: 12 Customer Support Technical Assis
Page 91 and 92: Japan Telephone: +813-5770-6312 Fax
Page 93 and 94: Appendix A Symbology Chart Symbolog
Page 95 and 96: Dec Hex Char Dec Hex Char Dec Hex C
Page 97 and 98: UPC A Sample Symbols 0 123456 7890
Page 99 and 100: Programming Chart 0 1 2 3 4 5 6 7 8
show all

User Manual

Create successful ePaper yourself

Delete template?

Save as template?