User Manual
User Manual User Manual
Straight 2 of 5 Industrial (three-bar start/stop) Straight 2 of 5 Industrial On * Off Straight 2 of 5 Industrial Message Length Scan the barcodes below to change the message length. Refer to Message Length on page 6-1 for additional information. Minimum and Maximum lengths = 1-48. Minimum Default = 4, Maximum Default = 48. Minimum Message Length Maximum Message Length Straight 2 of 5 IATA (two-bar start/stop) 6 - 10 3200 User’s Guide
Straight 2 of 5 IATA On * Off Straight 2 of 5 IATA Message Length Scan the barcodes below to change the message length. Refer to Message Length on page 6-1 for additional information. Minimum and Maximum lengths = 1-48. Minimum Default = 4, Maximum Default = 48. Minimum Message Length Matrix 2 of 5 Maximum Message Length Matrix 2 of 5 On * Off 3200 User’s Guide 6 - 11
- Page 1 and 2: User’s Guide 3200 Linear Imager
- Page 3 and 4: Table of Contents Chapter 1 - Getti
- Page 5 and 6: Interleaved 2 of 5 ................
- Page 7: Chapter 10 - Product Specifications
- Page 11 and 12: 1 Getting Started About This Manual
- Page 13 and 14: Plug and Play Plug and Play barcode
- Page 15 and 16: Note: For the imager to work proper
- Page 17 and 18: 2 Terminal Interfaces Terminal ID I
- Page 19 and 20: Keyboard Country Scan the appropria
- Page 21 and 22: Control + ASCII Mode On: The imager
- Page 23 and 24: RS-232 Word Length: Data Bits, Stop
- Page 25 and 26: 3 Output Good Read Indicators Beepe
- Page 27 and 28: 4 Data Editing Prefix/Suffix Overvi
- Page 29 and 30: To Clear One or All Prefixes or Suf
- Page 31 and 32: Intercharacter Delay An intercharac
- Page 33 and 34: 5 Data Formatting Data Format Edito
- Page 35 and 36: Move Commands F5 Move the cursor ah
- Page 37 and 38: 6 Symbologies Introduction This pro
- Page 39 and 40: No Check Character indicates that t
- Page 41 and 42: Code 39 Check Character No Check Ch
- Page 43 and 44: Code 39 Code Page Code pages define
- Page 45: Code 93 < Default All Code 93 Setti
- Page 49 and 50: Code 11 Message Length Scan the bar
- Page 51 and 52: Telepen On * Off Telepen Output Usi
- Page 53 and 54: This selection adds 2 or 5 digits t
- Page 55 and 56: UPC E0 and UPC E1 Addenda Required
- Page 57 and 58: This selection adds 2 or 5 digits t
- Page 59 and 60: This selection adds 2 or 5 digits t
- Page 61 and 62: MSI Message Length Scan the barcode
- Page 63 and 64: RSS Expanded * On Off RSS Expanded
- Page 65 and 66: 7 Interface Keys Keyboard Function
- Page 67 and 68: Supported Interface Keys IBM AT/XT
- Page 69 and 70: 8 Utilities To Add a Test Code I.D.
- Page 71 and 72: 9 Default Chart Resetting the Stand
- Page 73 and 74: Selection Beeper Volume - Good Read
- Page 75 and 76: Selection Interleaved 2 of 5 Check
- Page 77 and 78: Selection UPC A Addenda Required UP
- Page 79 and 80: Selection RSS Limited RSS Expanded
- Page 81 and 82: 10 Product Specifications 3200 Prod
- Page 83 and 84: Standard Cable Pinouts Serial Outpu
- Page 85 and 86: 11 Maintenance Repairs Repairs and/
- Page 87 and 88: Is the scanner having trouble readi
- Page 89 and 90: 12 Customer Support Technical Assis
- Page 91 and 92: Japan Telephone: +813-5770-6312 Fax
- Page 93 and 94: Appendix A Symbology Chart Symbolog
- Page 95 and 96: Dec Hex Char Dec Hex Char Dec Hex C
Straight 2 of 5 Industrial (three-bar start/stop)<br />
<br />
Straight 2 of 5 Industrial<br />
On<br />
* Off<br />
Straight 2 of 5 Industrial Message Length<br />
Scan the barcodes below to change the message length. Refer to Message<br />
Length on page 6-1 for additional information. Minimum and Maximum<br />
lengths = 1-48. Minimum Default = 4, Maximum Default = 48.<br />
Minimum Message Length<br />
Maximum Message Length<br />
Straight 2 of 5 IATA (two-bar start/stop)<br />
<br />
6 - 10 3200 <strong>User</strong>’s Guide