User Manual
User Manual User Manual
When Check Digit is set to Validate, but Don’t Transmit, the unit only reads Interleaved 2 of 5 barcodes printed with a check digit, but will not transmit the check digit with the scanned data. When Check Digit is set to Validate and Transmit, the imager only reads Interleaved 2 of 5 barcodes printed with a check digit, and will transmit this digit at the end of the scanned data. Default = No Check Digit. * No Check Digit Validate, but Don’t Transmit Validate and Transmit Interleaved 2 of 5 Message Length Scan the barcodes below to change the message length. Refer to Message Length on page 6-1 for additional information. Minimum and Maximum lengths = 2-80. Minimum Default = 4, Maximum Default = 80. Minimum Message Length Maximum Message Length 6 - 8 3200 User’s Guide
Code 93 < Default All Code 93 Settings > Code 93 * On Off Code 93 Message Length Scan the barcodes below to change the message length. Refer to Message Length on page 6-1 for additional information. Minimum and Maximum lengths = 0-80. Minimum Default = 0, Maximum Default = 80. Minimum Message Length Code 93 Code Page Maximum Message Length Code pages define the mapping of character codes to characters. If the data received does not display with the proper characters, it may be because the barcode being scanned was created using a code page that is different from the one the host program is expecting. If this is the case, scan the barcode below, select the code page with which the barcodes were created from the chart, Code Page Mapping of Printed barcodes on page A-4, and scan the value and the SAVE barcode from the Programming Chart inside the back cover of this manual. The data characters should then appear properly. Code 93 Code Page 3200 User’s Guide 6 - 9
- Page 1 and 2: User’s Guide 3200 Linear Imager
- Page 3 and 4: Table of Contents Chapter 1 - Getti
- Page 5 and 6: Interleaved 2 of 5 ................
- Page 7: Chapter 10 - Product Specifications
- Page 11 and 12: 1 Getting Started About This Manual
- Page 13 and 14: Plug and Play Plug and Play barcode
- Page 15 and 16: Note: For the imager to work proper
- Page 17 and 18: 2 Terminal Interfaces Terminal ID I
- Page 19 and 20: Keyboard Country Scan the appropria
- Page 21 and 22: Control + ASCII Mode On: The imager
- Page 23 and 24: RS-232 Word Length: Data Bits, Stop
- Page 25 and 26: 3 Output Good Read Indicators Beepe
- Page 27 and 28: 4 Data Editing Prefix/Suffix Overvi
- Page 29 and 30: To Clear One or All Prefixes or Suf
- Page 31 and 32: Intercharacter Delay An intercharac
- Page 33 and 34: 5 Data Formatting Data Format Edito
- Page 35 and 36: Move Commands F5 Move the cursor ah
- Page 37 and 38: 6 Symbologies Introduction This pro
- Page 39 and 40: No Check Character indicates that t
- Page 41 and 42: Code 39 Check Character No Check Ch
- Page 43: Code 39 Code Page Code pages define
- Page 47 and 48: Straight 2 of 5 IATA On * Off Strai
- Page 49 and 50: Code 11 Message Length Scan the bar
- Page 51 and 52: Telepen On * Off Telepen Output Usi
- Page 53 and 54: This selection adds 2 or 5 digits t
- Page 55 and 56: UPC E0 and UPC E1 Addenda Required
- Page 57 and 58: This selection adds 2 or 5 digits t
- Page 59 and 60: This selection adds 2 or 5 digits t
- Page 61 and 62: MSI Message Length Scan the barcode
- Page 63 and 64: RSS Expanded * On Off RSS Expanded
- Page 65 and 66: 7 Interface Keys Keyboard Function
- Page 67 and 68: Supported Interface Keys IBM AT/XT
- Page 69 and 70: 8 Utilities To Add a Test Code I.D.
- Page 71 and 72: 9 Default Chart Resetting the Stand
- Page 73 and 74: Selection Beeper Volume - Good Read
- Page 75 and 76: Selection Interleaved 2 of 5 Check
- Page 77 and 78: Selection UPC A Addenda Required UP
- Page 79 and 80: Selection RSS Limited RSS Expanded
- Page 81 and 82: 10 Product Specifications 3200 Prod
- Page 83 and 84: Standard Cable Pinouts Serial Outpu
- Page 85 and 86: 11 Maintenance Repairs Repairs and/
- Page 87 and 88: Is the scanner having trouble readi
- Page 89 and 90: 12 Customer Support Technical Assis
- Page 91 and 92: Japan Telephone: +813-5770-6312 Fax
- Page 93 and 94: Appendix A Symbology Chart Symbolog
Code 93<br />
< Default All Code 93 Settings ><br />
Code 93<br />
* On<br />
Off<br />
Code 93 Message Length<br />
Scan the barcodes below to change the message length. Refer to Message<br />
Length on page 6-1 for additional information. Minimum and Maximum<br />
lengths = 0-80. Minimum Default = 0, Maximum Default = 80.<br />
Minimum Message Length<br />
Code 93 Code Page<br />
Maximum Message Length<br />
Code pages define the mapping of character codes to characters. If the data<br />
received does not display with the proper characters, it may be because the<br />
barcode being scanned was created using a code page that is different from the<br />
one the host program is expecting. If this is the case, scan the barcode below,<br />
select the code page with which the barcodes were created from the chart, Code<br />
Page Mapping of Printed barcodes on page A-4, and scan the value and the<br />
SAVE barcode from the Programming Chart inside the back cover of this manual.<br />
The data characters should then appear properly.<br />
Code 93 Code Page<br />
3200 <strong>User</strong>’s Guide 6 - 9