User Manual
User Manual User Manual
Data Formatter When Data Formatter is turned off, the barcode data is output to the host as read (including prefixes and suffixes). Choose one of the following options. Default = Data Formatter On. * Data Formatter On, but Not Required Data Formatter Off When Data Formatter is required, all input data must conform to an edited format or the imager does not transmit the input data to the host device. Data Format On, Format Required 5 - 4 3200 User’s Guide
6 Symbologies Introduction This programming section contains the following menu selections. Refer to Chapter 9 for settings and defaults. • All Symbologies • Interleaved 2 of 5 • China Post Code • Matrix 2 of 5 • Codabar • MSI • Code 11 • Plessey Code • Code 39 • RSS-14 • Code 32 Pharmaceutical (PARAF) All Symbologies • Straight 2 of 5 IATA (two-bar start/stop) • Straight 2 of 5 • Code 93 Industrial (three-bar start/stop) • Code 128 • Telepen • UPC-A/EAN-13 with Extended Coupon Code • UPC A • EAN/JAN 8 • UPC E If you want to decode all the symbologies allowable for your imager, scan the All Symbologies On code. If on the other hand, you want to decode only a particular symbology, scan All Symbologies Off followed by the On symbol for that particular symbology. All Symbologies On All Symbologies Off Message Length You are able to set the valid reading length of some of the barcode symbologies. If the data length of the scanned barcode doesn’t match the valid reading length, the imager will issue an error beep. You may wish to set the same value for minimum and maximum length to force the imager to read fixed length barcode data. This helps reduce the chances of a misread. 3200 User’s Guide 6 - 1
- Page 1 and 2: User’s Guide 3200 Linear Imager
- Page 3 and 4: Table of Contents Chapter 1 - Getti
- Page 5 and 6: Interleaved 2 of 5 ................
- Page 7: Chapter 10 - Product Specifications
- Page 11 and 12: 1 Getting Started About This Manual
- Page 13 and 14: Plug and Play Plug and Play barcode
- Page 15 and 16: Note: For the imager to work proper
- Page 17 and 18: 2 Terminal Interfaces Terminal ID I
- Page 19 and 20: Keyboard Country Scan the appropria
- Page 21 and 22: Control + ASCII Mode On: The imager
- Page 23 and 24: RS-232 Word Length: Data Bits, Stop
- Page 25 and 26: 3 Output Good Read Indicators Beepe
- Page 27 and 28: 4 Data Editing Prefix/Suffix Overvi
- Page 29 and 30: To Clear One or All Prefixes or Suf
- Page 31 and 32: Intercharacter Delay An intercharac
- Page 33 and 34: 5 Data Formatting Data Format Edito
- Page 35: Move Commands F5 Move the cursor ah
- Page 39 and 40: No Check Character indicates that t
- Page 41 and 42: Code 39 Check Character No Check Ch
- Page 43 and 44: Code 39 Code Page Code pages define
- Page 45 and 46: Code 93 < Default All Code 93 Setti
- Page 47 and 48: Straight 2 of 5 IATA On * Off Strai
- Page 49 and 50: Code 11 Message Length Scan the bar
- Page 51 and 52: Telepen On * Off Telepen Output Usi
- Page 53 and 54: This selection adds 2 or 5 digits t
- Page 55 and 56: UPC E0 and UPC E1 Addenda Required
- Page 57 and 58: This selection adds 2 or 5 digits t
- Page 59 and 60: This selection adds 2 or 5 digits t
- Page 61 and 62: MSI Message Length Scan the barcode
- Page 63 and 64: RSS Expanded * On Off RSS Expanded
- Page 65 and 66: 7 Interface Keys Keyboard Function
- Page 67 and 68: Supported Interface Keys IBM AT/XT
- Page 69 and 70: 8 Utilities To Add a Test Code I.D.
- Page 71 and 72: 9 Default Chart Resetting the Stand
- Page 73 and 74: Selection Beeper Volume - Good Read
- Page 75 and 76: Selection Interleaved 2 of 5 Check
- Page 77 and 78: Selection UPC A Addenda Required UP
- Page 79 and 80: Selection RSS Limited RSS Expanded
- Page 81 and 82: 10 Product Specifications 3200 Prod
- Page 83 and 84: Standard Cable Pinouts Serial Outpu
- Page 85 and 86: 11 Maintenance Repairs Repairs and/
6<br />
Symbologies<br />
Introduction<br />
This programming section contains the following menu selections. Refer to<br />
Chapter 9 for settings and defaults.<br />
• All Symbologies • Interleaved 2 of 5<br />
• China Post Code • Matrix 2 of 5<br />
• Codabar • MSI<br />
• Code 11 • Plessey Code<br />
• Code 39 • RSS-14<br />
• Code 32 Pharmaceutical (PARAF)<br />
All Symbologies<br />
• Straight 2 of 5 IATA<br />
(two-bar start/stop)<br />
• Straight 2 of 5<br />
• Code 93<br />
Industrial (three-bar<br />
start/stop)<br />
• Code 128 • Telepen<br />
• UPC-A/EAN-13 with Extended<br />
Coupon Code<br />
• UPC A<br />
• EAN/JAN 8 • UPC E<br />
If you want to decode all the symbologies allowable for your imager, scan the All<br />
Symbologies On code. If on the other hand, you want to decode only a<br />
particular symbology, scan All Symbologies Off followed by the On symbol for<br />
that particular symbology.<br />
All Symbologies On<br />
All Symbologies Off<br />
Message Length<br />
You are able to set the valid reading length of some of the barcode symbologies.<br />
If the data length of the scanned barcode doesn’t match the valid reading length,<br />
the imager will issue an error beep. You may wish to set the same value for<br />
minimum and maximum length to force the imager to read fixed length barcode<br />
data. This helps reduce the chances of a misread.<br />
3200 <strong>User</strong>’s Guide 6 - 1
Change language