User Manual
User Manual User Manual
RS-232 Handshaking RS-232 handshaking is a set of rules concerning the exchange of data between serially communicating devices. Default = RTS/CTS, XON/XOFF and ACK/ NAK Off. RTS/CTS On * RTS/CTS Off XON/XOFF On ACK/NAK On * XON/OFF Off * ACK/NAK Off 2 - 8 3200 User’s Guide
3 Output Good Read Indicators Beeper – Good Read The beeper may be programmed On or Off in response to a good read. Turning this option off, only turns off the beeper response to a good read indication. All error and menu beeps are still audible. Default = On. * On Beeper Pitch – Good Read The beeper pitch codes modify the pitch (frequency) of the beep the imager emits on a good read. Default = Medium. Off Low (1600 Hz) High (4200 Hz) * Medium (2550 Hz) Trigger Modes Manual/Serial Trigger Trigger The following barcodes will allow you to use the reader in Manual Trigger mode (need to press the trigger to read) or Automatic Trigger mode (the beam is always on). * Manual/Serial Trigger 3200 User’s Guide 3 - 1
- Page 1 and 2: User’s Guide 3200 Linear Imager
- Page 3 and 4: Table of Contents Chapter 1 - Getti
- Page 5 and 6: Interleaved 2 of 5 ................
- Page 7: Chapter 10 - Product Specifications
- Page 11 and 12: 1 Getting Started About This Manual
- Page 13 and 14: Plug and Play Plug and Play barcode
- Page 15 and 16: Note: For the imager to work proper
- Page 17 and 18: 2 Terminal Interfaces Terminal ID I
- Page 19 and 20: Keyboard Country Scan the appropria
- Page 21 and 22: Control + ASCII Mode On: The imager
- Page 23: RS-232 Word Length: Data Bits, Stop
- Page 27 and 28: 4 Data Editing Prefix/Suffix Overvi
- Page 29 and 30: To Clear One or All Prefixes or Suf
- Page 31 and 32: Intercharacter Delay An intercharac
- Page 33 and 34: 5 Data Formatting Data Format Edito
- Page 35 and 36: Move Commands F5 Move the cursor ah
- Page 37 and 38: 6 Symbologies Introduction This pro
- Page 39 and 40: No Check Character indicates that t
- Page 41 and 42: Code 39 Check Character No Check Ch
- Page 43 and 44: Code 39 Code Page Code pages define
- Page 45 and 46: Code 93 < Default All Code 93 Setti
- Page 47 and 48: Straight 2 of 5 IATA On * Off Strai
- Page 49 and 50: Code 11 Message Length Scan the bar
- Page 51 and 52: Telepen On * Off Telepen Output Usi
- Page 53 and 54: This selection adds 2 or 5 digits t
- Page 55 and 56: UPC E0 and UPC E1 Addenda Required
- Page 57 and 58: This selection adds 2 or 5 digits t
- Page 59 and 60: This selection adds 2 or 5 digits t
- Page 61 and 62: MSI Message Length Scan the barcode
- Page 63 and 64: RSS Expanded * On Off RSS Expanded
- Page 65 and 66: 7 Interface Keys Keyboard Function
- Page 67 and 68: Supported Interface Keys IBM AT/XT
- Page 69 and 70: 8 Utilities To Add a Test Code I.D.
- Page 71 and 72: 9 Default Chart Resetting the Stand
- Page 73 and 74: Selection Beeper Volume - Good Read
RS-232 Handshaking<br />
RS-232 handshaking is a set of rules concerning the exchange of data between<br />
serially communicating devices. Default = RTS/CTS, XON/XOFF and ACK/<br />
NAK Off.<br />
RTS/CTS On<br />
* RTS/CTS Off<br />
XON/XOFF On<br />
ACK/NAK On<br />
* XON/OFF Off<br />
* ACK/NAK Off<br />
2 - 8 3200 <strong>User</strong>’s Guide