User Manual
User Manual User Manual
Please refer to Hand Held Products website ( www.handheld.com) for complete keyboard country support information and applicable interfaces. If you need to program a keyboard for a country other than one listed above, scan the Program Keyboard Country barcode below, then scan the numeric barcode(s) for the appropriate country from the inside back cover, then the Save barcode. Program Keyboard Country Keyboard Style This programs keyboard styles, such as Caps Lock and Shift Lock. Default = Regular. Regular is used when you normally have the Caps Lock key off. * Regular Caps Lock is used when you normally have the Caps Lock key on. Caps Lock Autocaps via NumLock barcode should be scanned in countries (e.g., Germany, France) where the Caps Lock key cannot be used to toggle Caps Lock. The NumLock option works similarly to the regular Auotcaps, but uses the NumLock key to retrieve the current state of the Caps Lock. Autocaps via NumLock Emulate External Keyboard should be scanned if you do not have an external keyboard (IBM AT or equivalent). Note: After scanning the Emulate External Keyboard barcode, you must power cycle your computer. Keyboard Modifiers Emulate External Keyboard This modifies special keyboard features, such as CTRL+ ASCII codes and Turbo Mode. 2 - 4 3200 User’s Guide
Control + ASCII Mode On: The imager sends key combinations for ASCII control characters for values 00-1F. Refer to Keyboard Function Relationships, page 7-1 for CTRL+ ASCII Values. Default = Off Control + ASCII Mode On * Control + ASCII Mode Off Numeric Keypad Mode: Sends numeric characters as if entered from a numeric keypad. Default = Off Numeric Keypad Mode On * Numeric Keypad Mode Off Automatic Direct Connect Mode: This selection can be used if you have an IBM AT style terminal and the system is dropping characters. Default = Off Automatic Direct Connect Mode On * Automatic Direct Connect Mode Off 3200 User’s Guide 2 - 5
- Page 1 and 2: User’s Guide 3200 Linear Imager
- Page 3 and 4: Table of Contents Chapter 1 - Getti
- Page 5 and 6: Interleaved 2 of 5 ................
- Page 7: Chapter 10 - Product Specifications
- Page 11 and 12: 1 Getting Started About This Manual
- Page 13 and 14: Plug and Play Plug and Play barcode
- Page 15 and 16: Note: For the imager to work proper
- Page 17 and 18: 2 Terminal Interfaces Terminal ID I
- Page 19: Keyboard Country Scan the appropria
- Page 23 and 24: RS-232 Word Length: Data Bits, Stop
- Page 25 and 26: 3 Output Good Read Indicators Beepe
- Page 27 and 28: 4 Data Editing Prefix/Suffix Overvi
- Page 29 and 30: To Clear One or All Prefixes or Suf
- Page 31 and 32: Intercharacter Delay An intercharac
- Page 33 and 34: 5 Data Formatting Data Format Edito
- Page 35 and 36: Move Commands F5 Move the cursor ah
- Page 37 and 38: 6 Symbologies Introduction This pro
- Page 39 and 40: No Check Character indicates that t
- Page 41 and 42: Code 39 Check Character No Check Ch
- Page 43 and 44: Code 39 Code Page Code pages define
- Page 45 and 46: Code 93 < Default All Code 93 Setti
- Page 47 and 48: Straight 2 of 5 IATA On * Off Strai
- Page 49 and 50: Code 11 Message Length Scan the bar
- Page 51 and 52: Telepen On * Off Telepen Output Usi
- Page 53 and 54: This selection adds 2 or 5 digits t
- Page 55 and 56: UPC E0 and UPC E1 Addenda Required
- Page 57 and 58: This selection adds 2 or 5 digits t
- Page 59 and 60: This selection adds 2 or 5 digits t
- Page 61 and 62: MSI Message Length Scan the barcode
- Page 63 and 64: RSS Expanded * On Off RSS Expanded
- Page 65 and 66: 7 Interface Keys Keyboard Function
- Page 67 and 68: Supported Interface Keys IBM AT/XT
- Page 69 and 70: 8 Utilities To Add a Test Code I.D.
Control + ASCII Mode On: The imager sends key combinations for ASCII<br />
control characters for values 00-1F. Refer to Keyboard Function<br />
Relationships, page 7-1 for CTRL+ ASCII Values. Default = Off<br />
Control + ASCII Mode On<br />
* Control + ASCII Mode Off<br />
Numeric Keypad Mode: Sends numeric characters as if entered from a<br />
numeric keypad. Default = Off<br />
Numeric Keypad Mode On<br />
* Numeric Keypad Mode Off<br />
Automatic Direct Connect Mode: This selection can be used if you have an<br />
IBM AT style terminal and the system is dropping characters. Default = Off<br />
Automatic Direct<br />
Connect Mode On<br />
* Automatic Direct Connect<br />
Mode Off<br />
3200 <strong>User</strong>’s Guide 2 - 5