Bluetooth Commands - wless.ru

More documents

Recommendations

Info

Chapter 4 – Examples Multi-Point Example Using MTS2BTSMI or MTS2BTA Four Master and One Slave Devices Note: Attaching the fourth master device can overload the connections and cause all connections to be terminated. Increasing the distance between Bluetooth devices will effect performance and could further limit the number of connections. Setup hardware for this example consisting of up to five MTS2BTSMI or MTS2BTA Bluetooth units connected through serial ports to workstations. One unit is configured as slave and four units are configured as masters. The slave needs to be firmware version 3.6.2.1.0.0 or newer to support multipoint connections. The masters are not firmware dependent and can be older models. All Bluetooth units are configured with baud rate of 9600bps, 8 data bits, no parity, 1 stop bit and hardware flow control. Baud rate can be set up to 115.2kbps but all Bluetooth devices need to be set to same baud rate. Each workstation uses a terminal emulator like HyperTerminal or ZOC to communicate to Bluetooth device using AT commands. Configure the slave Bluetooth device to function as slave in data mode. - Verify local device is Slave in Data Mode. Sent: ATSI,7 Reply: OK Reply: 0,1,0,0 - If not Slave, set to Slave in Data Mode and reset unit. Sent: ATSW25,0,1,0,0 Reply: OK - Enable multipoint mode and set number of connections to four. Then reset unit. Sent: ATSSW,3,4 Reply: OK Sent: ATURST Reply: OK - Retrieve Bluetooth address from Bluetooth slave device in this test setup. Sent: ATSI,1 Reply: OK Reply: 12-digit address OK Issue these AT commands at the master Bluetooth devices to generate four wireless connections between the four Masters and the slave device. - Verify local device is Master in Data Mode. Sent: ATSI,7 Reply: OK Reply: 1,1,0,0 - If not Master, set to Master in Data Mode and reset unit. Sent: ATSW25,1,1,0,0 Reply: OK Sent: ATURST Reply: OK - Perform an Inquiry to detect BT_Address of slave (unless it is already known). Sent: ATDI,1,00000000 {Class of Device} // Looks for one Bluetooth device Reply: OK // Search completed when DONE appears Reply: BT_Slave1_Address,00000000,SOCKETWIRELESS Reply: DONE - Perform a Master Connection over SPP to the Bluetooth slave device. Sent: ATDM, BT_Slave1_Address,1101 // SPP connection Reply: OK Reply: CONNECT,BT_Slave1_Address // Returns Slave BT address radio is in data mode Multi-Tech Systems, Inc. SocketWireless Bluetooth AT Commands (S000360G) 66
Chapter 4 – Examples - At second master device perform a Master Connection over SPP to the Bluetooth slave device. Sent: ATDM, BT_Slave1_Address,1101 // SPP connection Reply: OK Reply: CONNECT,BT_Slave1_Address // Returns Slave BT address radio is in data mode - At third master device perform a Master Connection over SPP to the Bluetooth slave device. Sent: ATDM, BT_Slave1_Address,1101 // SPP connection Reply: OK Reply: CONNECT,BT_Slave1_Address // Returns Slave BT address radio is in data mode - At fourth master device perform a Master Connection over SPP to the Bluetooth slave device. Sent: ATDM, BT_Slave1_Address,1101 // SPP connection Reply: OK Reply: CONNECT,BT_Slave1_Address // Returns Slave BT address radio is in data mode Send and receive data between master and slave devices. Sending data from the slave will be sent to all four masters. Sending data from a master device will be sent only to the slave device. Multi-Tech Systems, Inc. SocketWireless Bluetooth AT Commands (S000360G) 67
Page 1 and 2:
Bluetooth ® Commands AT Commands a
Page 3 and 4:
Table of Contents Table of Contents
Page 5 and 6:
Table of Contents RSSI and Link Qua
Page 7 and 8:
Chapter 1 - Introduction Overview C
Page 9 and 10:
Chapter 1 - Introduction Important
Page 11 and 12:
Chapter 1 - Introduction Multipoint
Page 13 and 14:
Chapter 1 - Introduction Test Scena
Page 15 and 16: Chapter 2 - AT Commands Chapter 2 -
Page 17 and 18: Chapter 2 - AT Commands Set/Get Dev
Page 19 and 20: Chapter 2 - AT Commands 11 GET PIO(
Page 21 and 22: Chapter 2 - AT Commands Security Co
Page 23 and 24: Chapter 2 - AT Commands SSNC Set Se
Page 25 and 26: Chapter 2 - AT Commands OP Overwrit
Page 27 and 28: Chapter 2 - AT Commands SW21 Write
Page 29 and 30: Chapter 2 - AT Commands SW23 Write
Page 31 and 32: Chapter 2 - AT Commands SW26 Lock U
Page 33 and 34: Chapter 2 - AT Commands Read Memory
Page 35 and 36: Chapter 2 - AT Commands Notes: •
Page 37 and 38: Chapter 2 - AT Commands Set Master
Page 39 and 40: Chapter 2 - AT Commands About Comma
Page 41 and 42: Chapter 2 - AT Commands Pairing Com
Page 43 and 44: Chapter 2 - AT Commands SSNIFF Enab
Page 45 and 46: Chapter 2 - AT Commands Notes: •
Page 47 and 48: Chapter 2 - AT Commands Link Superv
Page 49 and 50: Chapter 2 - AT Commands Making the
Page 51 and 52: Chapter 2 - AT Commands • If the
Page 53 and 54: Chapter 2 - AT Commands FTP Push/Pu
Page 55 and 56: Chapter 2 - AT Commands OPP Client
Page 57 and 58: Chapter 2 - AT Commands OPPPUSH Obj
Page 59 and 60: Chapter 2 - AT Commands OPP Server
Page 61 and 62: Chapter 4 - Examples Chapter 4 - Ex
Page 63 and 64: Chapter 4 - Examples DUN Point-to-P
Page 65: Chapter 4 - Examples - Perform a Ma
Page 69 and 70: Chapter 4 - Examples Issue these AT
Page 71 and 72: Appendix A - AT Command Summary Tab
Page 73 and 74: Appendix A - AT Command Summary Tab
Page 75 and 76: Appendix B - Responses AT Example L
Page 77 and 78: AT Example Long Response Example Sh
Page 79 and 80: Appendix B - Responses AT Example L
Page 81 and 82: Appendix C - UUID Table Appendix C
Page 83 and 84: Appendix E - Two Versions of Blueto
Page 85 and 86: Appendix E - Two Versions of Blueto
Page 87 and 88: Appendix F - Glossary, Acronyms, an
Page 89 and 90: IL - Last Inquiry..................
show all

Bluetooth Commands - wless.ru

Create successful ePaper yourself

Delete template?

Save as template?