Bluetooth Commands - wless.ru

More documents

Recommendations

Info

Chapter 2 – AT Commands DL Dial Last This command connects to last successful Slave Bluetooth address connection over SPP unless ATDM command was executed then the UUID from the ATDM command will be used. Format: ATDL Return Parameters: or Point-to-Point Example: TYPE: REPLY: ATDL OK CONNECT,123456789012 OR OK PAIRED,123456789012 CONNECT,123456789012 OR OK NO ANSWER OR ERROR // if security is enabled // if device not present Multi-Point Example: TYPE: ATDL REPLY: OK CONNECT,00,123456789012 OR OK PAIRED,123456789012 // if security is enabled CONNECT,123456789012 OR OK NO ANSWER // if device not present OR ERROR Notes: • To verify the stored address use the ATLAST command below. • If the remote Slave device is not present or the service is not available, NO ANSWER will reply after the master connect timeout and you will have to try again. • If security is enabled and the radio is connecting to a PC that has not yet been paired with it, the PAIRED,12345678912 message may return twice prior to the CONNECT. LAST Read Last Address Gets the last connected Bluetooth device address. Format: ATLAST Return Parameters: EXAMPLE: TYPE: ATLAST REPLY: OK 000000000000 // Nothing stored OR OK 123456789012 // Last connected BT address Multi-Tech Systems, Inc. SocketWireless Bluetooth AT Commands (S000360G) 36
Chapter 2 – AT Commands Set Master Default Bluetooth Address Commands SMA Set Master Default Address This command will set a specific Bluetooth Slave address and service profile into the Master device so on power up the Master will automatically search and connect to a unique Slave device on the highest available channel. Format: ATSMA,, Parameters: EXAMPLE: TYPE: REPLY: • BT Address: Bluetooth Address, 12 hex characters MAX • UUID: 4 digit, binary profile code (See Appendix C for more info) ATSMA,00A0961F904F,1101 OK OR ERROR Read Using: ATSI,9 Notes: • Execute ATSW25 to set the power up connect mode to auto-master before using the above command if still in slave mode. • This command is limited to only one connection. Reset module for change to take affect. MACLR Master Address Clear This command clears the stored slave address. Format: ATMACLR EXAMPLE: TYPE: ATMACLR REPLY: OK OR ERROR SSW,7 Set Auto Connect Master on Data This command connects automatically to the stored master address when data is present on the UART. The Radio will disconnect when the No Data timeout has been reached, this occurs when no data is being sent to the UART. The ATSMA command must be enabled before this will work. See the ATSW28 command to set the No Data timeout. Format: ATSSW7,1 EXAMPLE: TYPE: REPLY: ATSSW,7,1 OK OR ERROR RSW,7 Read Auto Connect Master on Data This command reads the AUTO CONNECT MASTER ON DATA enable/disable register state. Format: ATRSW,7 Return Parameters: EXAMPLE: TYPE: ATRSW,7 REPLY: OK 00 Set Using: ATSSW,7 Multi-Tech Systems, Inc. SocketWireless Bluetooth AT Commands (S000360G) 37
Page 1 and 2: Bluetooth ® Commands AT Commands a
Page 3 and 4: Table of Contents Table of Contents
Page 5 and 6: Table of Contents RSSI and Link Qua
Page 7 and 8: Chapter 1 - Introduction Overview C
Page 9 and 10: Chapter 1 - Introduction Important
Page 11 and 12: Chapter 1 - Introduction Multipoint
Page 13 and 14: Chapter 1 - Introduction Test Scena
Page 15 and 16: Chapter 2 - AT Commands Chapter 2 -
Page 17 and 18: Chapter 2 - AT Commands Set/Get Dev
Page 19 and 20: Chapter 2 - AT Commands 11 GET PIO(
Page 21 and 22: Chapter 2 - AT Commands Security Co
Page 23 and 24: Chapter 2 - AT Commands SSNC Set Se
Page 25 and 26: Chapter 2 - AT Commands OP Overwrit
Page 27 and 28: Chapter 2 - AT Commands SW21 Write
Page 29 and 30: Chapter 2 - AT Commands SW23 Write
Page 31 and 32: Chapter 2 - AT Commands SW26 Lock U
Page 33 and 34: Chapter 2 - AT Commands Read Memory
Page 35: Chapter 2 - AT Commands Notes: •
Page 39 and 40: Chapter 2 - AT Commands About Comma
Page 41 and 42: Chapter 2 - AT Commands Pairing Com
Page 43 and 44: Chapter 2 - AT Commands SSNIFF Enab
Page 45 and 46: Chapter 2 - AT Commands Notes: •
Page 47 and 48: Chapter 2 - AT Commands Link Superv
Page 49 and 50: Chapter 2 - AT Commands Making the
Page 51 and 52: Chapter 2 - AT Commands • If the
Page 53 and 54: Chapter 2 - AT Commands FTP Push/Pu
Page 55 and 56: Chapter 2 - AT Commands OPP Client
Page 57 and 58: Chapter 2 - AT Commands OPPPUSH Obj
Page 59 and 60: Chapter 2 - AT Commands OPP Server
Page 61 and 62: Chapter 4 - Examples Chapter 4 - Ex
Page 63 and 64: Chapter 4 - Examples DUN Point-to-P
Page 65 and 66: Chapter 4 - Examples - Perform a Ma
Page 67 and 68: Chapter 4 - Examples - At second ma
Page 69 and 70: Chapter 4 - Examples Issue these AT
Page 71 and 72: Appendix A - AT Command Summary Tab
Page 73 and 74: Appendix A - AT Command Summary Tab
Page 75 and 76: Appendix B - Responses AT Example L
Page 77 and 78: AT Example Long Response Example Sh
Page 79 and 80: Appendix B - Responses AT Example L
Page 81 and 82: Appendix C - UUID Table Appendix C
Page 83 and 84: Appendix E - Two Versions of Blueto
Page 85 and 86: Appendix E - Two Versions of Blueto
Page 87 and 88:
Appendix F - Glossary, Acronyms, an
Page 89 and 90:
IL - Last Inquiry..................
show all

Bluetooth Commands - wless.ru

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?