Bluetooth Commands - wless.ru

More documents

Recommendations

Info

Chapter 2 – AT Commands SW25 Write Connection, Comm, Unconnected UART, Default Service Modes This command configures connection, comm mode, unconnected UART, and default service modes. Warning – The only way to communicate to the device after setting the radio in “Fast Data Mode” and “ignore UART while unconnected” is to apply 3.3Vdc on PIO(4) during initial power up for >2 sec. These settings are used if you have no control over the source of streaming data into the radio, or you do not know when the radio has made a Bluetooth connection, and do not plan on sending any AT commands. Format: ATSW25,,,, Parameters: • Power-Up Connection Mode: 0 = Slave 1 = Auto-Master (Set ATSMA Command First). Auto-Connect Master always connects using the highest available channel. If none available it will continue to retry. 2 = Idle Mode. In idle mode the radio is neither slave nor master and draws 1.6mA of current but you can not communicate over the Bluetooth link in this state only through the TX & RX hardware UART. 3 = Slave Undiscoverable 5 = Repeater (Set ATSMA Command First). Repeater always uses channel 00 for slave and 01 for Master. Repeater also only uses SPP with no SCO connection. 6 = Mesh Configuration 7 = OPP Server (See FTP and OPP Modes Section for more info) 8 = FTP Server (See FTP and OPP Modes Section for more info) • Comm Mode: 0 = Fast Data. If data mode is set to “Fast Data Mode” in a Master unit during a manual inquiry “ATDI” and/or connection request the radio connects in slow data mode not fast. This is because you will need the capability to issue commands because in fast data mode the AT command parser is turned off. 1 = Data 2 = Command • Unconnected UART Mode: 0 = Allow Data to Pass While Unconnected 1 = Ignore Data While Unconnected • Default Service Profile: This field no longer has any effect; it can just be set to 0. Service profile UUIDs are now set using the ATSSNC command. Factory Default: Connection Mode = 0, Comm Mode = 1, Unconnected UART Mode = 0, Default Service Profile = 0 EXAMPLE: TYPE: ATSW25,0,1,0,0 //Slave radio connects in fast data mode REPLY: OK OR ERROR Read Using: ATSI,7 Notes: • Requires a reset for the settings to go into affect. • The comm mode parameter has no effect when operating in FTP or OPP mode. Multi-Tech Systems, Inc. SocketWireless Bluetooth AT Commands (S000360G) 30
Chapter 2 – AT Commands SW26 Lock User Settings This command locks user settings to prevent unauthorized local and remote access.. Warning – This command will lock the PIN. Format: ATSW26,, Parameters: • PIN: 16 alphanumeric characters MAX (Caps Sensitive, includes spaces) • Lock/Unlock: 0 = Unlocked 1 = Locked Factory Default: Unlocked EXAMPLE: TYPE: ATSW26,default,1 REPLY: OK OR ERROR Note: ATSW26 will still work after locking the user settings, allowing them to be unlocked. SW27 Write LED Rate This command sets the LED Pulse Rate on PIO(5). Format: ATSW27, Parameters: • Pulse Rate: Integer decimal value from 1ms to 60,000ms Factory Default: 1000 EXAMPLE: TYPE: ATSW27,1000 //1000 ms REPLY: OK OR ERROR Read Using: ATSI,11 Note: Used to indicate slave mode operation and inquiry in process. Duty cycle equals 50%. SW28 Write Inquiry and Master Timeout Settings This command configures inquiry and master connect timeout settings. Format: ATSW28,,, Parameters: • Inquiry Timeout: Integer value from 1 to 40 [seconds] • Master Connect Request Timeout: Integer value from 1 to 40 [seconds] • No Data Timeout: Integer value from 1 to 65535 [seconds] Factory Default: Inquiry Timeout = 16, Master Connect Request Timeout = 40, No Data Timeout = 60 EXAMPLE: TYPE: ATSW28,16,40,60 // factory default Read Using: Note: REPLY: OK OR ERROR ATSI,13 The master connect request timeout also controls the timeouts on the ATRRN, ATRRSN and ATPAIR commands. Multi-Tech Systems, Inc. SocketWireless Bluetooth AT Commands (S000360G) 31
Page 1 and 2: Bluetooth ® Commands AT Commands a
Page 3 and 4: Table of Contents Table of Contents
Page 5 and 6: Table of Contents RSSI and Link Qua
Page 7 and 8: Chapter 1 - Introduction Overview C
Page 9 and 10: Chapter 1 - Introduction Important
Page 11 and 12: Chapter 1 - Introduction Multipoint
Page 13 and 14: Chapter 1 - Introduction Test Scena
Page 15 and 16: Chapter 2 - AT Commands Chapter 2 -
Page 17 and 18: Chapter 2 - AT Commands Set/Get Dev
Page 19 and 20: Chapter 2 - AT Commands 11 GET PIO(
Page 21 and 22: Chapter 2 - AT Commands Security Co
Page 23 and 24: Chapter 2 - AT Commands SSNC Set Se
Page 25 and 26: Chapter 2 - AT Commands OP Overwrit
Page 27 and 28: Chapter 2 - AT Commands SW21 Write
Page 29: Chapter 2 - AT Commands SW23 Write
Page 33 and 34: Chapter 2 - AT Commands Read Memory
Page 35 and 36: Chapter 2 - AT Commands Notes: •
Page 37 and 38: Chapter 2 - AT Commands Set Master
Page 39 and 40: Chapter 2 - AT Commands About Comma
Page 41 and 42: Chapter 2 - AT Commands Pairing Com
Page 43 and 44: Chapter 2 - AT Commands SSNIFF Enab
Page 45 and 46: Chapter 2 - AT Commands Notes: •
Page 47 and 48: Chapter 2 - AT Commands Link Superv
Page 49 and 50: Chapter 2 - AT Commands Making the
Page 51 and 52: Chapter 2 - AT Commands • If the
Page 53 and 54: Chapter 2 - AT Commands FTP Push/Pu
Page 55 and 56: Chapter 2 - AT Commands OPP Client
Page 57 and 58: Chapter 2 - AT Commands OPPPUSH Obj
Page 59 and 60: Chapter 2 - AT Commands OPP Server
Page 61 and 62: Chapter 4 - Examples Chapter 4 - Ex
Page 63 and 64: Chapter 4 - Examples DUN Point-to-P
Page 65 and 66: Chapter 4 - Examples - Perform a Ma
Page 67 and 68: Chapter 4 - Examples - At second ma
Page 69 and 70: Chapter 4 - Examples Issue these AT
Page 71 and 72: Appendix A - AT Command Summary Tab
Page 73 and 74: Appendix A - AT Command Summary Tab
Page 75 and 76: Appendix B - Responses AT Example L
Page 77 and 78: AT Example Long Response Example Sh
Page 79 and 80: Appendix B - Responses AT Example L
Page 81 and 82:
Appendix C - UUID Table Appendix C
Page 83 and 84:
Appendix E - Two Versions of Blueto
Page 85 and 86:
Appendix E - Two Versions of Blueto
Page 87 and 88:
Appendix F - Glossary, Acronyms, an
Page 89 and 90:
IL - Last Inquiry..................
show all

Bluetooth Commands - wless.ru

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?