Bluetooth Commands - wless.ru

More documents

Recommendations

Info

Chapter 2 – AT Commands Security PIN Settings Commands SSW, 6 Set Pin Request Handling Mode Sets the PIN (Personal Identification Number) request handling mode. If set to 0 the PIN stored using the ATSP command will automatically be used during PIN exchanges. If set to 1 the prompt “PIN REQUEST” will be output by the radio and the user will need to manually enter a PIN using the ATPR command. Format: Parameters: ATSSW,6, Mode: 0 = Automatic PIN Request Handling 1 = Manual PIN Request Handling Factory Default: 0 EXAMPLE: TYPE: ATSSW,6,1 REPLY: OK OR ERROR Read Using: ATRSW,6 Note: Requires a reset for change to take affect. RSW,6 Read Pin Request Handling Mode Reads the PIN request handling mode. Format: ATRSW,6 Return Parameters: EXAMPLE: TYPE: ATRSW,6 REPLY: OK 00 Set Using: ATSSW,6 SP Set PIN Sets the PIN to be used with automatic PIN request handling. **Warning** Be careful when entering a new PIN. There is no way to obtain PIN status after it is changed. If the PIN is changed after two units have already been authenticated and connected, you will have to perform a software or hardware reset for the devices to use the new PINs. If this is not done, the two units will still connect using the old stored PIN. Format: ATSP,, Parameters: New PIN: 16 alphanumeric characters MAX (Caps Sensitive, includes spaces) Old PIN: 16 alphanumeric characters MAX (Caps Sensitive, includes spaces) Factory Default: default EXAMPLE: TYPE: ATSP,1234567890123456,default REPLY: OK OR ERROR Note: If security is enabled in multipoint mode, all connected slaves will have to use the same PIN. There is no way to assign an individual PIN to each slave. Multi-Tech Systems, Inc. SocketWireless Bluetooth AT Commands (S000360G) 24
Chapter 2 – AT Commands OP Overwrite PIN Overwrites the stored PIN without needing the old PIN. To use this command, the PIN must be unlocked using ATSW29. Format: ATOP, Parameters: PIN: 16 alphanumeric characters MAX (Caps sensitive, includes spaces) Example: Type: Reply: ATOP,1234 OK OR ERROR //If ATOP has not been enabled with ATSW29. PR Respond to Manual PIN Request Allows the user to manually enter a PIN after receiving the PIN REQUEST prompt from the device. Format: ATPR, Parameters: PIN: 16 alphanumeric characters MAX (Caps Sensitive, includes spaces) EXAMPLE: REPLY: PIN REQUEST TYPE: ATPR,default REPLY: OK OR ERROR Class of Device (COD) Commands SC Set Class of Device (COD) Sets the COD. Format: ATSC, Parameters: A Class of Device (COD) requires exactly eight 16-bit hex values (0 thru F) based on the Bluetooth COD specification names published and maintained by the Bluetooth SIG. Factory Default: 00000000 – Which is undefined since this is set by the user based on the final OEM device it is installed in. EXAMPLE: TYPE: ATSC,00020114 REPLY: OK OR ERROR Read Using: ATSI,5 Note: Requires a reset for change to take effect. Multi-Tech Systems, Inc. SocketWireless Bluetooth AT Commands (S000360G) 25
Page 1 and 2: Bluetooth ® Commands AT Commands a
Page 3 and 4: Table of Contents Table of Contents
Page 5 and 6: Table of Contents RSSI and Link Qua
Page 7 and 8: Chapter 1 - Introduction Overview C
Page 9 and 10: Chapter 1 - Introduction Important
Page 11 and 12: Chapter 1 - Introduction Multipoint
Page 13 and 14: Chapter 1 - Introduction Test Scena
Page 15 and 16: Chapter 2 - AT Commands Chapter 2 -
Page 17 and 18: Chapter 2 - AT Commands Set/Get Dev
Page 19 and 20: Chapter 2 - AT Commands 11 GET PIO(
Page 21 and 22: Chapter 2 - AT Commands Security Co
Page 23: Chapter 2 - AT Commands SSNC Set Se
Page 27 and 28: Chapter 2 - AT Commands SW21 Write
Page 29 and 30: Chapter 2 - AT Commands SW23 Write
Page 31 and 32: Chapter 2 - AT Commands SW26 Lock U
Page 33 and 34: Chapter 2 - AT Commands Read Memory
Page 35 and 36: Chapter 2 - AT Commands Notes: •
Page 37 and 38: Chapter 2 - AT Commands Set Master
Page 39 and 40: Chapter 2 - AT Commands About Comma
Page 41 and 42: Chapter 2 - AT Commands Pairing Com
Page 43 and 44: Chapter 2 - AT Commands SSNIFF Enab
Page 45 and 46: Chapter 2 - AT Commands Notes: •
Page 47 and 48: Chapter 2 - AT Commands Link Superv
Page 49 and 50: Chapter 2 - AT Commands Making the
Page 51 and 52: Chapter 2 - AT Commands • If the
Page 53 and 54: Chapter 2 - AT Commands FTP Push/Pu
Page 55 and 56: Chapter 2 - AT Commands OPP Client
Page 57 and 58: Chapter 2 - AT Commands OPPPUSH Obj
Page 59 and 60: Chapter 2 - AT Commands OPP Server
Page 61 and 62: Chapter 4 - Examples Chapter 4 - Ex
Page 63 and 64: Chapter 4 - Examples DUN Point-to-P
Page 65 and 66: Chapter 4 - Examples - Perform a Ma
Page 67 and 68: Chapter 4 - Examples - At second ma
Page 69 and 70: Chapter 4 - Examples Issue these AT
Page 71 and 72: Appendix A - AT Command Summary Tab
Page 73 and 74: Appendix A - AT Command Summary Tab
Page 75 and 76:
Appendix B - Responses AT Example L
Page 77 and 78:
AT Example Long Response Example Sh
Page 79 and 80:
Appendix B - Responses AT Example L
Page 81 and 82:
Appendix C - UUID Table Appendix C
Page 83 and 84:
Appendix E - Two Versions of Blueto
Page 85 and 86:
Appendix E - Two Versions of Blueto
Page 87 and 88:
Appendix F - Glossary, Acronyms, an
Page 89 and 90:
IL - Last Inquiry..................
show all

Bluetooth Commands - wless.ru

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?