Bluetooth Commands - wless.ru

More documents

Recommendations

Info

Chapter 2 – AT Commands Resetting the Device Commands URST Reset Tells the SocketWireless device to perform a software reset on the CPU Format: ATURST Example: Type: ATURST Reply: None Notes: • This unique Command does not reply with “OK” or “ERROR” because of the internal UART data processing limitations and response timing. • You can send the reset command through the UART or over the Bluetooth RF connection. FRST Factory Reset Resets the SocketWireless back to factory defaults. Example: Format: ATFRST Example: Type: ATFRST Reply: OK RESET COMPLETE or ERROR Note: You can send the factory reset command through the UART or over the Bluetooth RF connection. SSW, 0 Set Bypass for Hardware Factory Configuration Reset PIO(4) Use this command in replace of physically connecting PIO(4) to ground to prevent an inadvertent factory configuration reset. Format: ATSSW,0, Parameters: Enable/Disable: 0 = PIO(4) factory reset enabled 1 = PIO(4) factory reset disabled Example: Type: ATSSW,0,1 Reply: OK OR ERROR Read by Using: ATRSW,0 RSW, 0 Read Bypass for Hardware Factory Configuration Reset PIO(4) Use this command to read the PIO(4) factory reset enable/disable register state. Format: ATRSW,0 Parameters: Example: Type: ATRSW,0 Reply: OK OR 00 Set by Using: ATSSW,0 Multi-Tech Systems, Inc. SocketWireless Bluetooth AT Commands (S000360G) 16
Chapter 2 – AT Commands Set/Get Device Information Commands Status Information can be obtained directly from the device. This information is important when managing a connection list of devices in a local area and the current settings of the device. SI Status Information Gets specified status information from the LOCAL device. Format: ATSI, Parameters: Status Request: Integer 1 to 22 If "Set Using" field is listed, see listed AT command for more information on return parameters. 1 GET BT ADDRESS Return Parameters: EXAMPLE: TYPE: REPLY: ATSI,1 OK 123456789012 2 GET FRIENDLY NAME Set Using: ATSN Return Parameters: EXAMPLE: TYPE: REPLY: ATSI,2 OK SocketWireless 3 GET CURRENT CONNECTION STATUS (CH00-CH03) Return Parameters: Connection Status: Single Connection Format: (Mode, Ch00 State) MP Format: (Mode,Ch00 State,Ch01 State,Ch02 State,Ch03 State) Repeater Format: (Mode,Slave-Ch00 State,Master-Ch01 State) Modes: 0 = Slave 1 = Auto-Master 2 = Idle 3 = Slave Undiscoverable 5 = Repeater 6 = Mesh States: 0 = Disconnected 1 = Connected EXAMPLE: TYPE: REPLY: ATSI,3 OK 1,0,0,0,0 Note: This command does not report the status of any FTP or OPP connections. Use ATSI,22 to obtain FTP/OPP status. 4 GET SERVICE NAME Set Using: ATSSN Return Parameters: EXAMPLE: TYPE: REPLY: ATSI,4 OK COM0 Multi-Tech Systems, Inc. SocketWireless Bluetooth AT Commands (S000360G) 17
Page 1 and 2: Bluetooth ® Commands AT Commands a
Page 3 and 4: Table of Contents Table of Contents
Page 5 and 6: Table of Contents RSSI and Link Qua
Page 7 and 8: Chapter 1 - Introduction Overview C
Page 9 and 10: Chapter 1 - Introduction Important
Page 11 and 12: Chapter 1 - Introduction Multipoint
Page 13 and 14: Chapter 1 - Introduction Test Scena
Page 15: Chapter 2 - AT Commands Chapter 2 -
Page 19 and 20: Chapter 2 - AT Commands 11 GET PIO(
Page 21 and 22: Chapter 2 - AT Commands Security Co
Page 23 and 24: Chapter 2 - AT Commands SSNC Set Se
Page 25 and 26: Chapter 2 - AT Commands OP Overwrit
Page 27 and 28: Chapter 2 - AT Commands SW21 Write
Page 29 and 30: Chapter 2 - AT Commands SW23 Write
Page 31 and 32: Chapter 2 - AT Commands SW26 Lock U
Page 33 and 34: Chapter 2 - AT Commands Read Memory
Page 35 and 36: Chapter 2 - AT Commands Notes: •
Page 37 and 38: Chapter 2 - AT Commands Set Master
Page 39 and 40: Chapter 2 - AT Commands About Comma
Page 41 and 42: Chapter 2 - AT Commands Pairing Com
Page 43 and 44: Chapter 2 - AT Commands SSNIFF Enab
Page 45 and 46: Chapter 2 - AT Commands Notes: •
Page 47 and 48: Chapter 2 - AT Commands Link Superv
Page 49 and 50: Chapter 2 - AT Commands Making the
Page 51 and 52: Chapter 2 - AT Commands • If the
Page 53 and 54: Chapter 2 - AT Commands FTP Push/Pu
Page 55 and 56: Chapter 2 - AT Commands OPP Client
Page 57 and 58: Chapter 2 - AT Commands OPPPUSH Obj
Page 59 and 60: Chapter 2 - AT Commands OPP Server
Page 61 and 62: Chapter 4 - Examples Chapter 4 - Ex
Page 63 and 64: Chapter 4 - Examples DUN Point-to-P
Page 65 and 66: Chapter 4 - Examples - Perform a Ma
Page 67 and 68:
Chapter 4 - Examples - At second ma
Page 69 and 70:
Chapter 4 - Examples Issue these AT
Page 71 and 72:
Appendix A - AT Command Summary Tab
Page 73 and 74:
Appendix A - AT Command Summary Tab
Page 75 and 76:
Appendix B - Responses AT Example L
Page 77 and 78:
AT Example Long Response Example Sh
Page 79 and 80:
Appendix B - Responses AT Example L
Page 81 and 82:
Appendix C - UUID Table Appendix C
Page 83 and 84:
Appendix E - Two Versions of Blueto
Page 85 and 86:
Appendix E - Two Versions of Blueto
Page 87 and 88:
Appendix F - Glossary, Acronyms, an
Page 89 and 90:
IL - Last Inquiry..................
show all

Bluetooth Commands - wless.ru

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?