Spare part catalogue

Spare part catalogue
IMESA Washing machine (Drain valve)
LM5 EDVG
LM5 EDVI
Via degli Olmi, 22 Il Zona Industriale
31040 Cessalto (TV)
Tel. 0421/468011 – Fax. 0421/468000

IMESA Prof v IT ss
Outer casing
Pos. Component Description Qty Remark
1 8061817-95 TOP COVER STAINLESS 1
2 8900338 SCREW RTK ST 4,2X9,5 FZB T20 3
2 8901413 LOCK WASHER AZ 4,3 GALV 2
3 8064062 STRIP TOP COVER WMD20 1
6 8801174-95 SIDE PLATE COMPL. WM20 2
7 8061763 GUIDE FRONT PLATE/TOP COVER 2
8 8061916 CABLE HOLDER WMD20 3
12 8061732-95 FRONT PLATE SS WM20 1
13 8900327 SCREW RTS ST 4,2X13 FZB T20 4
13 8901413 LOCK WASHER AZ 4,3 GALV 2
14 8064177 HOOK LOWER PANEL 2
15 8061741 RUBBER BUFFER FRONT DOOR WM20 2
15 8900338 SCREW RTK ST 4,2X9,5 FZB T20 2
16 8061744 HINGE BEARING 2
17 8901097 SCREW MRT-TT 4X12 FZB T20 3
18 8061745 RUBBER BUFFER HINGE WM20 2
19 8064293-95 LOWER COVER SS WM20 1 See Service No. 47
20 8900327 SCREW RTS ST 4,2X13 FZB T20 2
20 8901413 LOCK WASHER AZ 4,3 GALV 2
20 8064097 PLUG GUARD OUTLET VALVE 1
22 8061930 GUARD OUTLET VALVE WM20 1
23 8061657-33 DOOR OUTLET PUMP WM20 1
27 8061737 REAR PANEL WM20 1
28 8900338 SCREW RTK ST 4,2X9,5 FZB T20 8
30 8064160 TIP GUARD SET WM20 1
31 8061693 TRANSPORT BEAM 1
32 8900338 SCREW RTK ST 4,2X9,5 FZB T20 4
32 8901413 LOCK WASHER AZ 4,3 GALV 1
33 8064206 TRANSPORT SLEEVE COMPL. BLACK 3
34 8901037 SCREW BUFO 8.8 8X70 GALV 3
35 8061767 LOCKINGWASHER CROSSBAR WM20 3
36 8061799 HOLDER HOSE, REAR PANEL 2
37 8056647 CONNECTION PIPE 3/4"-3/4" 2
38 8007513 OUTLET HOSE (90 DEGREES) 1
39 8061618 BOTTOM WMD20 1
40 8059334 RUBBER FOOT D35xM10 INC. NUT 4

IMESA Prof v IT ss
Lower session
Pos. Component Description Qty Remark
1 8801171 SPRING LEG KIT WM20 1 See Service No. 153
2 8055796 RUBBER BUFFER SPRING LEG. 4
3 8055797 RUBBER BUFFER SPRING LEG. 4
4 8061668 RUBBER DAMPER SPRINGLEG 4
5 8901343 WASHER SRKB 11X28X2 FZB 6
5 8901193 NUT LOC-KING 8 BH8 GALV 4
5 33256445 WASHER, SPRING LEG 37X37X2 4
6 8063734 MOTOR FHP 50/60HZ WM55/66 1 See Service No. 163
7 8058261 SPAC.TUBE MOTOR SUSP. 12X191 2
8 8063591 SCREW 8.8 M8x205 FZB 2
9 8901155 NUT M6M8 BH8 GALV 2
9 8901337 WASHER BRB 8,4X16 HB 200 GALV 1
10 8086404 CABLE SET ST2-MO WM66/55 1
11 8061399 CONTROL UNIT MOTOR WM120-220 1
12 8061918 HOLDER MOTOR CONTROLLER WM20 1
13 8901322 WASHER SRB 4,3X12X1 GALV. 1
13 8901097 SCREW MRT-TT 4X12 FZB T20 1
15 8061925 BELLOWS HOSE OUTLET VALVE WM20 1
16 8063262 HOSE CLIP 80.0-708 1
17 8063607 HOSE CLIP 57.5-708 1
18 8052083 HOSE CLIP RFZ 39.6-706R 1
19 8061924 PRESSURE CHAMBER WM20 1
20 7382670 RUBBER HOSE 5X8X550 1
21 8008365 OUTLET VALVE MDB-2 454R 1
22 8062114 HOLDER, OUTLET VALVE WM20 1
23 8901969 SCREW MRT-TT 5x12 FZB T25 2
24 8901969 SCREW MRT-TT 5x12 FZB T25 2
25 8053401 DRIP GUARD, OUTLET VALVE 1
26 8062111 OUTLET HOSE, OUTLET VALVE WM20 1
27 8051391 HOSE CLIP RFZ 57,4-60,5 1
28 33700183 TERMINAL ESPA 1
29 8901413 LOCK WASHER AZ 4,3 GALV 1
29 8901097 SCREW MRT-TT 4X12 FZB T20 1
30 8061738 HOLDER THERMISTOR WM20 1
31 8061663 THERMISTOR (E30) 1
32 8061976 CABLE HOLDER SMALL 2
33 8054485 CABLE STRIP T50R SF/PH 1
40 8061704 HEATINGELEM. 1000W 230V FUSE 1
40 8061703 HEATINGELEM. 2000W 230V FUSE 1
41 33700450 CABLE STRIP T 30 R 1
42 8051391 HOSE CLIP RFZ 57,4-60,5 1
43 8050702 T-TUBE, OUTLET 1
44 8901322 WASHER SRB 4,3X12X1 GALV. 2
44 8901097 SCREW MRT-TT 4X12 FZB T20 2

IMESA Prof v IT ss
Lower session
Pos. Component Description Qty Remark
45 8064028 PROTECTIVE LID D=35 1
46 8052083 HOSE CLIP RFZ 39.6-706R 1

IMESA Prof v IT ss
Cylinder and related parts
Pos. Component Description Qty Remark
1 8061650-42 FRONT DOOR COMPL. VELOUR/GREY 1 See Service No. 158
2 8061651-96 FRAME FRONT DOOR OUTER VELOUR 1
3 8061652-42 FRAME FRONT DOOR INNER WM20 1
4 8061685 FRONT GLASS D306x42mm WM20 1
5 8061798 LOCK HOOK WM20 1
6 8061653 SEAL FRONT DOOR 1
7 8061624 SECURING PLATE FRONTGLAS 4
8 8061686-42 HINGE FRONT DOOR GREY WM20 1
9 8061687 SHAFT FOR HINGE WM20 1
10 8901969 SCREW MRT-TT 5x12 FZB T25 2
11 8061671-26 COVER PLATE OUTER BLACK 1
12 8061879 TENSIONSPRING COVERPLATE OUTER 4
14 8061616 GAPSEALING, SIDE WM20 2
15 8061670 COVER PLATE , INNER 1
16 8061678 DAMPER WEIGHT 2
17 8901135 SCREW M6SF-TT 8X25 DRILOC FZB 3
18 8061679 DOOR LOCK WM20 1 See Service No. 149
19 8061780 EMERGENCY OPENING COMPL. WM20 1
20 8061680 CONTACT GUARD, DOOR LOCK WM20 1
21 8061677 FRONT PANEL TUB WM20 1
22 8061889 SEALING STRIP FRONT PANEL(TUB) 1
23 8061669 TENSION RING WM20 1
24 8901335 WASHER BRB 6,4X12 HB 200 GALV 1
24 8901154 NUT M6 BH8 GALV 1
24 8901116 SCREW MC6S 6x85 8.8 FZB 1
25 8061600 CYLINDER COMPL. WM20 1 See Service No. 160
26 8061604 DRUM PADDLE WM20 3
27 8061682 DRIVE BELT 5EPJ 1209 1
28 8058497 O-RING 26,2X3 NBR70 DW95 1
29 8061638 V-RING CASSETTE COMPL. 1
30 8056314 BALL BEARING 6206 2RS MTSRL 2
31 8801165 CONTAINER COMPL. WM20 1
32 8056810 SCALE WASHER 37x30,5x0,5 1
33 8056376 PULLEY COMPL. D292 1
34 8057209 WASHER 42X10X4 1
35 8901052 SCRREW BUFO 8,8 10X25 GALV 1

IMESA Prof v IT ss
Control panel
Pos. Component Description Qty Remark
1 8064223-69 PANEL W. HANDLE IMESA IT 1
2 8901591 BINDING CLIP SCO 5740 4
3 8063377-49 PLATE PROG.INFO. WMC55 OEM 1
4 8061630 DETERGENT COMP. WM20 1
5 8061633 DIVIDER DETERGENT COMP. 1
6 8061634 SIPHON WM20 1
7 8061782-69 HANDLE PANEL OEM MECH. 0
11 8063990-33 PUSHBUTTONS WMC55 OEM 1
12 8063729 DISPLAY UNIT OEM WMD20 1
13 8061950-69 PUSHBUTTON MAINSWITCH OEM 1
15 8061822 DECOR LENS 1
16 8064069 INDICATION LAMP WM55/66 1
19 8061857 SPRING MAIN SWITCH WMD20 1
90 8064221 INSTAL/MAINTEN.MANUAL IMESA IT 1

IMESA Prof v IT ss
Upper session
Pos. Component Description Qty Remark
1 8061690 BEAM FRONT WM20 1
2 8900338 SCREW RTK ST 4,2X9,5 FZB T20 1
3 8061661 DETERGENT COMPARTMENT 1
4 8901970 SCREW PTK 40X14 A2 WN1452 T20 2
5 8902072 SCREW PT KB40X10 WN1442 GALV 1
6 8061628 BELLOWS HOSE INLET WM20 1
7 8063607 HOSE CLIP 57.5-708 1
8 8061702 RUBBER HOSE 10x15x300 3
9 8056656 CABLE STRIP 1
10 8061736 VENTILATION HOSE WM20 1
11 8052730 HOSE CLIP OETIKER 21.0-706R 1
15 8061757 INLET VALVE 3-WAY WM20 1
16 8901097 SCREW MRT-TT 4X12 FZB T20 2
17 8061875 PUSHBUTTONSW. 2-POLE CLOS. 1
24 8061921 HOLDER PROG.CONTROLLER WMD20 1
25 8063941 CONTROL UNIT WMC55 1
26 8061692 BRACKET FOR ELEC.COMP. WM20 1
27 8900338 SCREW RTK ST 4,2X9,5 FZB T20 2
28 8900327 SCREW RTS ST 4,2X13 FZB T20 1
30 8061664 PRESSURE CENSOR TYPE 1166 1
31 8061747 LEVEL SWITCH WM20 1
32 8003641 RUBBER HOSE 5X8X45 1
33 7382985 RUBBER HOSE 5X8X100 1
34 8051843 Y-PIPE 05 1
35 8061997 GUARD, LEVELSWITCH HOSE WM20 2
36 8061975 CABLE HOLDER BIG 1
37 8061694 CROSS BEAM 1
38 8900327 SCREW RTS ST 4,2X13 FZB T20 4
39 8061660 TERMINAL BLOCK 5-POLE 1
40 8901097 SCREW MRT-TT 4X12 FZB T20 1
41 8000158-1 MAINS CABLE 5X1.5X2000 1
42 8058558 RADIOINTERF.SUPP. FILTER 1
43 8901419 LOCK WASHER AZ 8,4 GALV 1
43 8901168 NUT ML6M 8 FZB 1
44 8054613 FUSE HOLDER HTB38 1
45 8054614 INSERT FUSE HOLDER STM 1
46 8055421 FUSE 1
47 8061923 BALANCING SPRING WM20 2
59 8061729 INLET VALVE 1-WAY WM20 1

IMESA Prof v IT ss
Outer door
Pos. Component Description Qty Remark
1 8061733-95 DOOR, OUTER PART SS WMD20 1
2 8061734-95 DOOR INNER PART SS WM20 1
3 8900395 SCREW KFTS ST 3.5X13 FZB T10 5
4 8061656-26 HANDLE FRONT DOOR BLACK WM20 1
5 8056201 CLIPS SNU 5552 4
5 8900395 SCREW KFTS ST 3.5X13 FZB T10 4
6 8061764 REINFORCEMENT HINGE WM20 2
7 8901969 SCREW MRT-TT 5x12 FZB T25 4
8 8901097 SCREW MRT-TT 4X12 FZB T20 4
9 8061906 HINGE ELECTRIC GALVANIZ. WM20 2
10 8901192 NUT LOCKING 6 BH8 GALV 1
10 7382628 WASHER, NYLON 6,2X14X1 1
10 8901004 SCREW BUFO 8.8 6X16 GALV 1
12 8061777-33 GUIDE HINGE BLACK WM20 2
15 8061742 TENSION SPRING, HINGE WM20 1
16 8061909 GLIDESLEEVE DOORSPRING WM20 1

SERVICE
I N F O R M A T I O N
Product: WM33/44/55/66
Date: 00-06-14
Reference: N-Å Carlsson
Remedy for thumping
noise from the cylinder
Group: 21
Number: 160
ÄO: 7792 Page: 1(1)
A thumping noise may appear on machines manufactured prior to week 38, 1999.
Reason:
The reason could be that gap has occurred between the mounting of the driving arms (at the cross) in
the cylinder. The thumping noise can be heard during the washing cycle, but does not affect operation.
Remedy:
1.Remove the cylinder. Refer to the Service Manual, part no. 6300341 (Swedish) or part no.
6300342 (English).
2.Apply DOW CORNING silicone, part no. 8064009, on both sides of all driving arms. Apply silicone
between the driving arm and the cylinder until silicone penetrates from the hole in the driving arm.
See the picture.
3.Reinstall the cylinder.

SERVICE
I N F O R M A T I O N
Product: Frontloaded
Date: 00-06-14
Reference:Bo Fredriksson
Leak in front door
WM 33/44/55/66 och
WMC 55
Group: 21
Number: 158
ÄO: 7782 Page: 1(1)
Service intervention for leaking front door.
First verify that the door seal is not damaged or covered by lose particles.
In order to increase the sealing strip pressure against the sealing surface of the container, a special O-
ring (part no. 8064178) has been designed.
As of Week 19, 2000, the front door O-ring is factory installed on all WMC 55 Professional models.
The front door O-ring can be fitted on earlier WMC 55 models as well as on WMC 33-44-55-66 to
remedy a leaking front door seal.
Fitting the front door O-ring, part no. 8064178
Fit the O-ring by placing it on the outside, covering the sealing strip (see picture) between the plastic
part of the door and the sealing strip. See the figure.
Picture
Figur 1
Placement of O-ring

SERVICE
I N F O R M A T I O N
Product: WM 33/44/55/66
Date: 00-03-15
Reference: Per Svensson
Wiring information
Door lock WM 33, 44, 55, 66
Group: 21
Number: 149
ÄO: 7301 Page: 1(1)
A modification to door hinge article no. 8061679 has led to the following changes:
1. Door hinge is now labelled (wiring information 1, 2, 3).
2. Leads DL1 and DL3 have swapped markings.
3. Wiring diagram has changed. Diagrams 8061751 rev. 00 and 8061753 rev 00 have been replaced
by rev. 01.
These changes have been made to machines manufactured after week 22, 1999.
New marking WM 33/44.
Individual leads
Lead marked DL 1 colour grey/red
Lead marked DL 2 colour grey
Lead marked DL 3 orange
New marking WM 55/66.
Connector block
Lead marked DL 1 colour grey
Lead marked DL 2 colour grey
Lead marked DL 3 colour grey
1
2
3
DL 1 grey/red
DL 2 grey
DL 3 orange
1
2
3
DL1
DL2
DL3
grey
Previous marking
WM 33/44
DL 3 grey/red
DL 2 grey
DL 1 orange
Previous marking
WM 55/66
DL 3 grey
DL 2 grey
DL 1 grey
NOTE!
Incorrect connection will cause a short-circuit.
The relative positions are unchanged. It is only the markings on the leads that have changed

SERVICE
I N F O R M A T I O N
Product:WM 55/66
Date:11-11-25
Reference:N-Å Carlsson
Change in make of motor
WM 55/66 WMC 55
Group: 21
Number: 163
ÄO: 7987 Page: 1(1)
A new motor made by FHP has been introduced as an alternative to the Ceset motor.
The two motors are fully interchangeable.
The reason for the change is to raise the quality of our washing machines
With effect from week 48, year 2000, the FHP motor will be fitted exclusively to all washing
machine models WM 55/66 and WMC 55. This motor will also be supplied as a spare part.
FHP motor
The following changes have been made:
With effect from October 2000 the Ceset motor has been replaced with a motor from FHP.
Both makes of motor will be used over the transition period.
Motor Article no. Motor Article no.
FHP 8063734 (EU/ AU/ US) Replaces Ceset 8061773 (EU AU)
FHP 8063734 (EU/ AU/ US) Replaces Ceset 8061774 (US)

SERVICE
I N F O R M A T I O N
Product: WMC 55
Date: 00-03-15
Reference: N-Å Carlsson
Water levels for WMC 55
(Professional)
Group: 21
Number: 157
ÄO: Page: 1(1)
Measurement must be carried out without laundry in machine.
Level for first rinse approx. 29 litres
Level for other rinses approx. 20 litres
Wash level Wool programme approx. 14.5 litres
Wash level approx. 11 litres

SERVICE
I N F O R M A T I O N
Product: WM 33 / 44
Date: 00-03-15
Reference: N-Å Carlsson
Description of fault indications
WM 33/44 (Timer)
Group: 21
Number: 151
ÄO: Page: 1(2)
Description of probabable cause when timer stops in position C (Check) or S (Safety)
In position C, the kind of fault can be checked by yourself, see service manual, but
faults in position S are often of more serious kind and requires service action.
C - CHECK STEP
Thermistor fault
Indicated when the out gate for the thermistor is closed or fully open
Heating element fault
Indicated when temperature setting not has been reached within:
25 minutes for wool wash cycle,
80 minutes for other cycles.
Timer fault
Indicated when the code transmission in the control unit is incorrect.
Water inlet fault
Indicated when over filling is sensed by the mechanical or electronical
level switch/sensor:
If the set level not is reached within 5 minutes
or if drain level not is passed within 3 minutes.
S - SAFETY STEP
Motor fault
Indicated if the tacho generator gates or the triac are short
cut or open, or if the safety relay KL1 is open
Pressure sensor fault
Indicated when water inlet to wash level or rinse level is not reached within 5 minutes,
though the mechanical level switch is operating at setted level.

Product: WM 55 / 66
Description of fault indications
SERVICE
I N F O R M A T I O N
Group: 21
Date: 00-03-15
WM 55/66 (Electronic)
Number: 151
Reference: N-Å Carlsson
ÄO: Page: 2(2)
Description of probabable cause when fault message is shown on the display.
Water inlet
Indicated when the set level not is reached within 5 minutes
Over flow
Indicated when the floaterswitch in the bottom (WM66) or overfill level is passed and sensed by the
level sensor.
Water outlet
Indicated when the drain level is not passed within 3 minutes.
Thermistor
Indicated when the out gate for the thermistor is closed or fully open
Temperature stop
Indicated when temperature setting not has been reached within:
25 minutes for wool wash cycle,
80 minutes for other cycles.
Wash motor
Indicated if the tacho generator is overloaded or control signal is missing
Pressure sensor
Indicated when water level is decreasing dropp to zero level within 15 seconds in the first rinse.
Foaming
Indicated when the level not have decreased to a certain level during the first outlet after main wash.
The level is neither aloud to be higher than the level giving indication for draining fault
Sensor
Indicated when the control signal from the rinse sensor is missing.
Door lock
Indicated when one of two transistors in the control circuit is broken
0000
Indicated when to big unbalance occured during spinning, ending in no fulfilled spinning cycle.

SERVICE
I N F O R M A T I O N
Product: WM 55/66
Date: 99-10-20
Reference: B Haglund
WM 55 / 66
Fault tracing
Group: 21
Number: 155
ÄO: Page: 1(2)
A
The machine do not start. No control lamp indication
Check: Fuse - 6,3 A.
B
Check:
Indicates Motor fault. Do not drain with drain pump.
The motor overspeeds and makes long interruptions.
Cable MO1 and ST2-1 and tab in motor.
Cable MO2 and ST2-2 and tab in motor.
Tachofunction
C
Indicates Motor fault. Do not drain with drain pump.
Fills water just for a short time.
Check: Cable ST1-5 and E6-1
Cable ST1-4 and E6-2.
Cable ST1-3 and E6-3.
Cable ST1-2 and E6-4.
Cable ST1-1 and E6-5.
To delete indication Motor fault: Turn the main switch off and then on again.
D
Check:
Indicates Motor fault. Do not drain with drain pump.
The motor do not run. Fills water to normal wash level.
Connection between rotor – brushes – cable terminals

SERVICE
I N F O R M A T I O N
Product: WM 55/66
Date: 00-03-15
Reference: B Haglund
WM 55 / 66
Fault tracing
Group: 21
Number: 155
ÄO: Page: 2(2)
E
Check:
Do not heat. Fills water to correct level.
Supply Voltage, Heater, Thermistor, Level switch, Control unit, as below
Start on program 3. It now runs for 8 minutes with soaking speed (40 rpm),
and thereafter turns over to normal speed (52 rpm) and the heating starts.
1. Check with water at correct level and with supply voltage:
1.1 Voltage by heater (230 V).
see also 2.1-2.2 below
1.2. Supply voltage line-side L :
Between N (E5-2) and E10-3 or E10-1 (230 V)
(note: Some circuit diagrams have been incorrect, E10-5 shall be E10-1).
1.3 Supply voltage neutral-side :
Between L1 (E5-1) and TB1-2, N1-11 or N1-14 (230 V)
If no voltage at N1-14 = incorrect level or faulty level switch.
2. Check with water at correct level and no supply voltage:
2.1. Heater - No break down of heater.
2.2 Thermistor - check value = 40-60 kohm by 20-30º C. (Higher value by lower temp)
F
The motor runs but there is no filling of water
Indicates overfilling when empty and the drain pump operates.
Check: Connection between E9 and level sensor N2.
G
Check:
Overfills - Over filling protection operates, no indication is shown
Starting the drainage pump with door opening button is not possible
Connection between E9-3 and N2-1.

Product: Dryer / Washer
Date:11-11-25
Reference:N-Å Carlsson
New mounting for bottom door
– tumble dryers and washing
machines
SERVICE
I N F O R M A T I O N
Group: 21 / 22
Number: 47
ÄO: 7997 Page: 1(1)
The bottom door mounting on tumble dryers and washing machines has been modified to
give a more efficient and durable solution.
This modification has been introduced on machines manufactured after week 45, year 2000
The new mounting will not fit machines manufactured before week 46. See table below.
New mounting – Dryers
The door is now opened by lifting the bottom
edge.
Fitting the door. Attach top half first.
2
2
Washing machines and some
dryers
New articles
8064177 Hook for bottom door
8900327 Screw 4.2 x 13 FZB T 20
Previous opening.
All washing machines and some
dryers
attached with 2 screws at base.
No change from before.
Obsolete articles
8061927 Clip, bottom door
8061928 Clip, bottom door
8063937 Guide, bottom door
8901619 Pop rivet Al 4x10
8062120 Guide, lower door
This change means new article numbers for bottom doors.
Article no. from week 46, year 2000 Article no. before week 46, year 2000
8064294-0 Bottom door assy. WM20 8063926-0 Bottom door assy. WM20
8064293-95 Bottom door assy. Stainless WM20 8061739-95 Bottom door assy. Stainless WM20
8064292-0-49-95 Bottom door. Louvred TD 20 8061850-0-49-95 Bottom door. Louvred TD 20

SERVICE
I N F O R M A T I O N
Product: WM 33/44/55/66
Date: 00-03-15
Reference: N-Å Carlsson
Spring legs
WM 33/44/55/66
Group: 21
Number: 153
ÄO: 7165/7166 Page: 1(1)
Changing of spring legs has been done as below:
Machines produced before week 11 1999 have spring leg nr 8061683 with a power of
27,5 + 12,5 -0 on all four legs.
Machines produced after week 11 1999 have spring legs with different power for left and
right side.
Spring legs with part nr. 8061981 with a power of 27,5 + 0 - 12,5 are mounted on left side.
Red text with partnumber on the spring legs.
Spring legs with part nr.8061683 with a power of 27,5 + 12,5 -0 are mounted on the right side.
Black text with the part number on the spring leg.
Complete kit with all 4 springlegs on part number . 8801171
no. 80 619
Red text
Left side.
Black text
Right side.
no. 80 616 83
Bottom
Front