LanTEKÂ® II Series Manual - Ideal Industries Inc.

More documents

Recommendations

Info

Chapter 5 Autotest Illustration 1 5.12. Single test overview 5. Press Enter again to open test series of single test. Illustration 2 5.12. Test series 6. Use Arrow Keys to navigate to desired test series and press Enter to display result table. Illustration 3 5.12. Result Table 7. Use Arrow Keys to navigate to desired test result and press Enter to display graph. 55
Chapter 5 Autotest Illustration 4 5.12. NEXT Graph When opening graph, cursor is always in worst case margin. In this example, cursor is positioned on horizontal axis at 186 MHz. 8. Press Escape to return to previous screen. 5.12.1. Graph Formats, Layouts and Controls Graphs make it easier to recognize the relation between two network parameters, the actually measured values and the pre-programmed limits. The horizontal axis indicates the frequency values and the vertical axis the measured values in dB. The limits are drawn as solid line. Table view Graph view Illustration 5.12.1. Table View and Graph View The margins indicated at lower right in table view provide information on worst case distance between the actual measuring values and the specified limits, as shown by the cursor position in the graph on the right. Description 1 Wire pair, plotted on the basis of the table data. 2 Specified limit curve for worst case loss value. 56
Page 1 and 2:
LanTEK ® II Series Manual 0
Page 3 and 4:
Standard Warranty Policy of IDEAL I
Page 5 and 6: Table of contents CHAPTER 1 Your La
Page 7 and 8: Table of contents 6.11.1. Insertion
Page 9 and 10: Table of contents 13.1. Technical S
Page 11 and 12: Chapter 1 Your LanTEK ® II Cable C
Page 13 and 14: CHAPTER 2 Product Description 2.1.
Page 15 and 16: Chapter 2 Product Description 2.1.2
Page 17 and 18: Chapter 2 Product Description 2.2.
Page 19 and 20: 2.3. Power Management Chapter 2 Pro
Page 21 and 22: CHAPTER 3 Basics of the Cable Test
Page 23 and 24: Chapter 4 Preferences 1. Use Arrow
Page 25 and 26: Chapter 4 Preferences 1. Use Arrow
Page 27 and 28: Chapter 4 Preferences 6. Use soft k
Page 29 and 30: CHAPTER 5 Autotest Using Autotest,
Page 31 and 32: Chapter 5 Autotest Autotest Pref Th
Page 33 and 34: Chapter 5 Autotest 2. Use Arrow Key
Page 35 and 36: Chapter 5 Autotest 5.3.1. Simple Ca
Page 37 and 38: Chapter 5 Autotest 3. Use Alphanume
Page 39 and 40: Chapter 5 Autotest 5.4.1. Cable Nam
Page 41 and 42: Chapter 5 Autotest AAA A / AAA A -
Page 43 and 44: Chapter 5 Autotest Illustration 2 5
Page 45 and 46: Chapter 5 Autotest 20. Make correct
Page 47 and 48: Chapter 5 Autotest 5.6. DualMODE Fu
Page 49 and 50: Chapter 5 Autotest Illustration 2 5
Page 51 and 52: Chapter 5 Autotest 5.9. Calibration
Page 53 and 54: Chapter 5 Autotest 5.9.2. Coaxial C
Page 55: Chapter 5 Autotest 3. Use soft key
Page 59 and 60: CHAPTER 6 Structured Cabling Testin
Page 61 and 62: Chapter 6 Structured cabling testin
Page 65 and 66: 6.11. Insertion Loss Test (Attenuat
Page 73 and 74: CHAPTER 8 Fiber Testing with FiberT
Page 75 and 76: Chapter 8 Fiber testing (LWL) Fiber
Page 87 and 88: CHAPTER 9 Tone Generator 9.1. Tone
Page 89 and 90: CHAPTER 10 IDEAL DataCENTER Softwar
Page 91 and 92: Chapter 10 IDEAL DataCENTER Softwar
Page 105 and 106: Chapter 11 LanTEK Firmware Upgrade
Page 107 and 108:
Standards Organization Classificati
Page 109 and 110:
Chapter 13 Customer Service North/S
show all

LanTEKÂ® II Series Manual - Ideal Industries Inc.

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?