LanTEK® II Series Manual - Ideal Industries Inc.
LanTEK® II Series Manual - Ideal Industries Inc. LanTEK® II Series Manual - Ideal Industries Inc.
Chapter 5 Autotest 5. Press AUTOTEST. The passed/failed results are displayed. For each DualMODE test, the worst case margins and values for NEXT, RL, ACR und Loss are indicated. Illustration 2 5.6.1. Overall DualMODE Result 6. Use Enter to load the corresponding graphical result displays of the highlighted test. 5.7. Edit NVP Default Value of a Cable To perform length measurement, the nominal velocity of propagation (NVP) of the cable must be known. This value can be found in the technical cable information. If this information is not available, a cable of known length (ca. 30 – 60 meter) should be connected, and the NVP calculated by LanTEK ® II Cable Tester. 1. Open "Cable Type" on start screen. 2. Use Arrow Keys to navigate to desired cable type. Illustration 1 5.7. NVP Default Value 3. Use soft key to open menu for entering NVP. 47
Chapter 5 Autotest Illustration 2 5.7. Enter NVP 4. Use Alphanumeric keys to enter one or several NVP. 5. For automatic calculation of a new NVP, press . Illustration 3 5.7. Calculation of NVP 6. Connect a cable of known length. 7. Use Arrow Keys and Number Keys to enter known cable length. 8. For automatic calculation of a new NVP, press . After calculation of new NVP, the display returns to the NVP main screen. NOTE: This concerns a channel measurement. When entering the cable length, the length of both patch cords must be considered. 5.8. Coaxial Cable Standards The LanTEK ® II Cable Tester supports the following coaxial cable standards: CATV standards Ethernet standards Other cable types RG59 31 or 92 m (3-fold or 4-fold shield) RG6 31 or 92 m (3-fold or 4-fold shield) 10Base 2 10Base 5 IBM Coax TWINAXIAL ARCNET 1. Open "Cable Type" on start screen. 48
- Page 1 and 2: LanTEK ® II Series Manual 0
- Page 3 and 4: Standard Warranty Policy of IDEAL I
- Page 5 and 6: Table of contents CHAPTER 1 Your La
- Page 7 and 8: Table of contents 6.11.1. Insertion
- Page 9 and 10: Table of contents 13.1. Technical S
- Page 11 and 12: Chapter 1 Your LanTEK ® II Cable C
- Page 13 and 14: CHAPTER 2 Product Description 2.1.
- Page 15 and 16: Chapter 2 Product Description 2.1.2
- Page 17 and 18: Chapter 2 Product Description 2.2.
- Page 19 and 20: 2.3. Power Management Chapter 2 Pro
- Page 21 and 22: CHAPTER 3 Basics of the Cable Test
- Page 23 and 24: Chapter 4 Preferences 1. Use Arrow
- Page 25 and 26: Chapter 4 Preferences 1. Use Arrow
- Page 27 and 28: Chapter 4 Preferences 6. Use soft k
- Page 29 and 30: CHAPTER 5 Autotest Using Autotest,
- Page 31 and 32: Chapter 5 Autotest Autotest Pref Th
- Page 33 and 34: Chapter 5 Autotest 2. Use Arrow Key
- Page 35 and 36: Chapter 5 Autotest 5.3.1. Simple Ca
- Page 37 and 38: Chapter 5 Autotest 3. Use Alphanume
- Page 39 and 40: Chapter 5 Autotest 5.4.1. Cable Nam
- Page 41 and 42: Chapter 5 Autotest AAA A / AAA A -
- Page 43 and 44: Chapter 5 Autotest Illustration 2 5
- Page 45 and 46: Chapter 5 Autotest 20. Make correct
- Page 47: Chapter 5 Autotest 5.6. DualMODE Fu
- Page 51 and 52: Chapter 5 Autotest 5.9. Calibration
- Page 53 and 54: Chapter 5 Autotest 5.9.2. Coaxial C
- Page 55 and 56: Chapter 5 Autotest 3. Use soft key
- Page 57 and 58: Chapter 5 Autotest Illustration 4 5
- Page 59 and 60: CHAPTER 6 Structured Cabling Testin
- Page 61 and 62: Chapter 6 Structured cabling testin
- Page 63 and 64: Chapter 6 Structured cabling testin
- Page 65 and 66: 6.11. Insertion Loss Test (Attenuat
- Page 67 and 68: Chapter 6 Structured cabling testin
- Page 69 and 70: Chapter 6 Structured cabling testin
- Page 71 and 72: Chapter 6 Structured cabling testin
- Page 73 and 74: CHAPTER 8 Fiber Testing with FiberT
- Page 75 and 76: Chapter 8 Fiber testing (LWL) Fiber
- Page 77 and 78: Chapter 8 Fiber testing (LWL) Fiber
- Page 79 and 80: Chapter 8 Fiber testing (LWL) Fiber
- Page 81 and 82: Chapter 8 Fiber testing (LWL) Fiber
- Page 83 and 84: Chapter 8 Fiber testing (LWL) Fiber
- Page 85 and 86: Chapter 8 Fiber testing (LWL) Fiber
- Page 87 and 88: CHAPTER 9 Tone Generator 9.1. Tone
- Page 89 and 90: CHAPTER 10 IDEAL DataCENTER Softwar
- Page 91 and 92: Chapter 10 IDEAL DataCENTER Softwar
- Page 93 and 94: Chapter 10 IDEAL DataCENTER Softwar
- Page 95 and 96: Chapter 10 IDEAL DataCENTER Softwar
- Page 97 and 98: Chapter 10 IDEAL DataCENTER Softwar
Chapter 5<br />
Autotest<br />
5. Press AUTOTEST. The passed/failed results are displayed. For each DualMODE<br />
test, the worst case margins and values for NEXT, RL, ACR und Loss are indicated.<br />
Illustration 2 5.6.1. Overall DualMODE Result<br />
6. Use Enter to load the corresponding graphical result displays of the highlighted<br />
test.<br />
5.7. Edit NVP Default Value of a Cable<br />
To perform length measurement, the nominal velocity of propagation (NVP) of the cable must<br />
be known. This value can be found in the technical cable information. If this information is<br />
not available, a cable of known length (ca. 30 – 60 meter) should be connected, and the NVP<br />
calculated by LanTEK ® <strong>II</strong> Cable Tester.<br />
1. Open "Cable Type" on start screen.<br />
2. Use Arrow Keys to navigate to desired cable type.<br />
Illustration 1 5.7. NVP Default Value<br />
3. Use soft key to open menu for entering NVP.<br />
47