Mi Distribution boards - IC SYSTEMS automatika

More documents

Recommendations

Info

Mi Distribution boards Technical details References/Types Technics HENPAS LES MC Mi KV DK Service Rated power dissipation of empty boxes The following table indicates the maximum rated power dissipation for any empty boxes. A difference is made between single boxes with lateral, frontal and rear radiation, an equipment with frontal and rear radiation. Box type 174 External dimensions W x H x D in mm Power dissipation (W/box) single box Mi 0100 300x150x170 25 18 Mi 0101 300x150x170 25 18 Mi 0200 300x300x170 40 32 Mi 0201 300x300x170 40 32 Mi 0210 300x300x214 46 38 Mi 0211 300x300x214 46 38 Mi 0220 300x300x182 40 32 Mi 0221 300x300x182 40 32 Mi 0300 300x450x170 53 45 Mi 0301 300x450x170 53 45 Mi 0310 300x450x214 65 53 Mi 0311 300x450x214 65 53 Mi 0400 300x600x170 70 58 Mi 0401 300x600x170 70 58 Mi 0410 300x600x214 82 60 Mi 0411 300x600x214 82 60 Mi 0400 + Mi ZR 4 Mi 0401 + Mi ZR 4 300x600x255 85 60 300x600x255 85 60 Mi 0800 600x600x170 120 98 Mi 0801 600x600x170 120 98 Mi 0800 + Mi ZR 8 Mi 0801 + Mi ZR 8 600x600x255 142 120 600x600x255 142 120 in assemblies The values indicated refer to the ambient temperature of 25° C and an interior temperature of 55° C. For the nominal load factor the square dependence of the power dissipation from the current shall be taken into consideration. Rated current and short circuit resistance of busbars Rated current A busbar crosssection mm Material Rated peak withstand current I pk kA cos ϕ 250 12x10 Cu 30 0,3 300 400 20x10 Cu 30 0,3 300 630 30x10 Cu 45 0,3 300 distances between busbar supports max. mm Mi-distribution boards comply with the requirements for type-tested switchgear and controlgear assemblies (TTA) in accordance with IEC 60 439-1/EN 60 439-1. Type-tested switchgear assemblies are switchgear and controlgear assemblies which are assembled and wired according to manufacturer data without essential deviations from the original type or system. To meet these requirements for Hensel Mi Distribution boards, the following must be noted: 1. The switchgear must consist of the type-tested enclosures documented in this list. 2. The wiring of the equipment must be carried out with the cross-sections and conductor types indicated in Table „Rating of insulated conductors in switchgear assemblies“, Index Technics, page 212. 3. Once the switchgear is completed, a routine test must be carried out in accordance with this standard. 4. The test must be certified with a test report. 5. The switchgear must be provided with a manufacturer’s identification mark. Compliance with important data such as - limit of temperature rise - dielectric strength - short-circuit withstand capacity - short-circuit withstand capacity of the PE conductor - IP degrees of protection - creepage distances and clearances is verified by type tests for this system. Mi-distribution boards comply with the following standards and requirements: - IEC 60 439-1 / EN 60 439-1 Low voltage swichgear and control gear assemblies - IEC 999 and EN 60 999 Safety requirements for screw-type and screwless-type clamping units for electrical copper conductors - EN 50 262 Metric threaded cable glands for electrical installations - IEC 269 Low voltage fuses - DIN 43 880 Built-in equipment for electrical installations; overall dimensions and related mounting dimensions - IEC 60 529 Degrees of protection provided by enclosures (IP-Code) Approvals: EZU Czech Republic MEEI Hungary
Mi Distribution boards Subline Technical details Dimensions in mm Dimensions of the interior installation depth with installed mounting plates. Mi 0100 Mi 0101 Mi 0310 Mi 0311 Service Mi DK Mi 0200 Mi 0201 KV MC LES HENPAS Mi 0300 Mi 0301 Mi 0210 Mi 0211 Mi 0220 Mi 0221 Mi 0400 Mi 0401 Mi 0410 Mi 0411 Technics Mi 0800 Mi 0801 175 References/Types
Page 1 and 2: Mi Distribution boards Technics HE
Page 3 and 4: Mi Distribution boards Contents Mi
Page 5 and 6: Mi Distribution boards System conf
Page 7 and 8: Mi Distribution boards Empty boxes
Page 9 and 10: Mi Distribution boards Empty boxes
Page 11 and 12: Mi Distribution boards Circuit-bre
Page 13 and 14: Mi Distribution boards Circuit-bre
Page 15 and 16: Mi Distribution boards KWH meter b
Page 17 and 18: Mi Distribution boards Busbar boxe
Page 19 and 20: Mi Distribution boards Mi isolator
Page 21 and 22: Mi Distribution boards Mi MCCB cir
Page 23 and 24: Mi Distribution boards Accessories
Page 43: Mi Distribution boards Technical d
Page 47 and 48: Mi Distribution boards Technical d
Page 49 and 50: Mi Distribution boards Technical d
Page 51 and 52: Mi Distribution boards Assembly
Page 53 and 54: Mi Distribution boards Assembly As

Mi Distribution boards - IC SYSTEMS automatika

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?