Sony STR-DE335.pdf - Hifi-pictures.net

More documents

Recommendations

Info

REAR PANEL SECTION 2 connector (CNP901) 4 rear panel section 3 two screws (BVTP3 × 8) 1 flat wire (CNS205) 2 connector (CNP500) 3 seven screws (BVTP3 × 8) 3 four screws (BVTP3 × 8) 1 flat wire (CNS401) MAIN BOARD SECTION 2 connector (CNP702) 3 three screws (BVTP3 × 8) 1 flat wire (CNS503) 2 connector (CNS802) 3 three screws (BVTP3 × 8) 5 MAIN board section 1 three flat wires (CNS204, CNP404) 2 two connectors (CNP703, 704) 2 connector (CNP801) 4 PC board holder – 8 –
Initialization Mode All preset contents are cleared when this mode is activated. When returning the unit to the customer after completing repairs, perform this operation to clear the unit. Procedure: 1. While pressing two buttons of [TUNER] and [MD/TAPE] simultaneously, press the 1/u button to turn the power ON. 2. The message “INITIAL” appears and initialization is performed. Fluorescent Indicator Tube Test Mode All fluorescent segments are tested. When this test is activated, all segments turn on at the same time, then each segment turns on one after another. Procedure: 1. While pressing two buttons of [TV/SAT] (US , Canadian and Australian models)* and [DIRECT] simultaneously, press the 1/u button to turn the power ON. 2. All segments turn on at the same time, then each segment and LED turns on one after another. 3. The message “FINISH” appears when this test is complete. *) Except US, Canadian and Australian models are [TV/LD] AUTO-BETICAL Check Mode (AEP model) To auto-scanning and memories of RDS station. Procedure: 1. While pressing the [MEMORY] button, press the 1/u button to turn the power ON. 2. The message “AUTO BET” appears and each function is selected one after another. AM Tuning Interval Selection Mode (US, Canadian and E models) Either 9 kHz step or 10 kHz step can be selected for the AM tuning interval. Procedure: 1. Set the FUNCTION to AM. 2. Press the 1/u button to turn the power OFF. 3. While pressing the [TUNING+] or [PRESET+]button, press the 1/u button to turn the power ON. 4. Either the message 10 k STEP” or “10k STEP” appears. 5. Select the desired step. Software Version Display Mode The software version is displayed. Procedure: 1. While pressing two the buttons of [MD/TAPE] and [DIRECT] simultaneously, press the 1/u button to turn the power ON. 2. The software version is displayed. SOUND FIELD Setting Clear Mode All SOUND FIELD setting are cleared. Procedure: 1. While pressing the [SOUND FIELD ON/OFF] button, press the 1/u button to turn the power ON. 2. The message “SURR CLR” appears and all SOUND FIELD setting are cleared. SECTION 4 TEST MODE – 9 –
Page 1 and 2: STR-DE335/SE391/V323 SERVICE MANUAL
Page 3 and 4: TABLE OF CONTENTS 1. SERVICING NOTE
Page 5 and 6: SECTION 2 GENERAL Location of contr
Page 7: Note: Follow the disassembly proced
Page 11 and 12: STR-DE335/SE391/V323 5-2. BLOCK DIA
Page 13 and 14: 5-4. NOTE FOR PRINTED WIRING BOARDS
Page 15 and 16: STR-DE335/SE391/V323 5-5. PRINTED W
Page 17 and 18: STR-DE335/SE391/V323 5-7. SCHEMATIC
Page 19 and 20: STR-DE335/SE391/V323 5-9. SCHEMATIC
Page 21 and 22: STR-DE335/SE391/V323 5-11. PRINTED
Page 23 and 24: STR-DE335/SE391/V323 5-13. PRINTED
Page 25 and 26: • IC Block Diagrams - MAIN BOARD
Page 27 and 28: 5-15. IC PIN FUNCTION DESCRIPTION
Page 29 and 30: SECTION 6 EXPLODED VIEWS NOTE: •
Page 31 and 32: (3) CHASSIS SECTION 104 105 #1 103
Page 33 and 34: DISPLAY NOTE: • Due to standardiz
Page 35 and 36: KEY MAIN Ref. No. Part No. Descript
Page 37 and 38: MAIN Ref. No. Part No. Description
Page 39 and 40: MAIN Ref. No. Part No. Description
Page 41 and 42: PHONO POWER SWITCH PRIMARY REAR AMP
Page 43 and 44: TONE VIDEO VOL SEL VOLUME Ref. No.
Page 45: STR-DE335/SE391/V323 9-928-870-11 S

Sony STR-DE335.pdf - Hifi-pictures.net

Create successful ePaper yourself

Delete template?

Save as template?