European Technical Approval Technical Approval ETA 12 ... - Hempel
European Technical Approval Technical Approval ETA 12 ... - Hempel European Technical Approval Technical Approval ETA 12 ... - Hempel
Page 8 of 46 of ETA 12/0581, issued on 17.01.2013 3.3.2 Example of CE marking Example of CE marking and accompanying information for product: “CE” symbol xxxx Hempel A/S Lundtoftevej 150 DK-2800 Kgs Lyngby Denmark Number of the notified body Name and address of the manufacturer YY xxxx-CPD-xxxx ETA 12/0581 ETAG 018, Part 1 and 2 Fire Protective products HEMPACORE ONE 43600 / HEMPACORE ONE FD 43601 Last two digits of year of affixing CE marking Number of the EC Certificate of Conformity Number of the ETA Reference to the corresponding ETAG Product name See ETA for relevant characteristics 4 Assumptions under which the fitness of the product(s) for the intended use was favourably assessed The detailed description and conditions of the manufacturing process of product, and all the relevant design and installation criteria of product are specified in the technical documentation of the manufacturer deposited with the ITeC. The main aspects of this information are specified in the following chapters. 4.1 Manufacturing The European Technical Approval is issued for the reactive coatings HEMPACORE ONE 43600 and HEMPACORE ONE FD 43601 on the basis of agreed data/information deposited with the ITeC, which identifies the products that have been assessed and judged. Changes to the products or production processes, which could result in this deposited data/information being incorrect, should be notified to ITeC before the changes are introduced. ITeC will decide whether such changes affect the ETA and consequently the validity of the CE marking on the basis of the ETA and, if so, whether further assessment or alterations to the ETA shall be necessary. 4.2 Installation 4.2.1 Reactive coating 4.2.2 Primer This ETA is issued under the assumption that the application of HEMPACORE ONE 43600 and HEMPACORE ONE FD 43601 occurs in accordance with the manufacturer’s instructions. The manufacturer shall provide an installation guide for his product in accordance with the installation provisions followed for the assessement in this ETA. A primer from the list of approved primers in section 1.2.2, or other compatible primers of the same family as specified by the manufacturer, shall be used. The preparation of the steel
Page 9 of 46 of ETA 12/0581, issued on 17.01.2013 surface and the application of the primers shall be in accordance with the manufacturer’s instructions. 4.2.3 Topcoat A topcoat from the list of approved topcoats in section 1.2.2 shall be used. The application of the topcoats shall be in accordance with the manufacturer’s instructions. 5 Recommendations 5.1 Recommendations on packaging, transport and storage In the accompanying documentation or on the containers, the manufacturer shall give information as to transport and storage. At least the following shall be indicated: type of storage (container, tank, etc.), minimum and maximum temperature for transport and storage. In case of combustible components or other potentially dangerous substances the instructions shall contain indications about limitations and/or conditions for handling, transport and storage. 5.2 Recommendations on use, maintenance and repair The assessment of the fitness for use is based on the assumption that necessary maintenance and repair, if required, is carried out in accordance with the manufacturer’s instructions during the assumed intended working life. The topcoat, where necessary, shall protect the reactive coating from moisture and other environmental influences. Therefore it shall always be kept in a proper state. In case of an execution without topcoat the control shall refer to the reactive coating. If the maintenance work related to the reactive coating or the topcoating is necessary, the manufacturer’s instructions shall be respected. On behalf of the Catalonia Institute of Construction Technology. Barcelona, 17 January 2013 Anton Maria Checa Torres General Manager, ITeC
- Page 1 and 2: The Catalonia Institute of Construc
- Page 3 and 4: Page 3 of 46 of ETA 12/0581, issued
- Page 5 and 6: Page 5 of 46 of ETA 12/0581, issued
- Page 7: Page 7 of 46 of ETA 12/0581, issued
- Page 11 and 12: Page 11 of 46 of ETA 12/0581, issue
- Page 13 and 14: Page 13 of 46 of ETA 12/0581, issue
- Page 15 and 16: Page 15 of 46 of ETA 12/0581, issue
- Page 17 and 18: Page 17 of 46 of ETA 12/0581, issue
- Page 19 and 20: Page 19 of 46 of ETA 12/0581, issue
- Page 21 and 22: Page 21 of 46 of ETA 12/0581, issue
- Page 23 and 24: Page 23 of 46 of ETA 12/0581, issue
- Page 25 and 26: Page 25 of 46 of ETA 12/0581, issue
- Page 27 and 28: Page 27 of 46 of ETA 12/0581, issue
- Page 29 and 30: Page 29 of 46 of ETA 12/0581, issue
- Page 31 and 32: Page 31 of 46 of ETA 12/0581, issue
- Page 33 and 34: Page 33 of 46 of ETA 12/0581, issue
- Page 35 and 36: Page 35 of 46 of ETA 12/0581, issue
- Page 37 and 38: Page 37 of 46 of ETA 12/0581, issue
- Page 39 and 40: Page 39 of 46 of ETA 12/0581, issue
- Page 41 and 42: Page 41 of 46 of ETA 12/0581, issue
- Page 43 and 44: Page 43 of 46 of ETA 12/0581, issue
- Page 45 and 46: Page 45 of 46 of ETA 12/0581, issue
Page 9 of 46 of <strong>ETA</strong> <strong>12</strong>/0581, issued on 17.01.2013<br />
surface and the application of the primers shall be in accordance with the manufacturer’s<br />
instructions.<br />
4.2.3 Topcoat<br />
A topcoat from the list of approved topcoats in section 1.2.2 shall be used. The application of<br />
the topcoats shall be in accordance with the manufacturer’s instructions.<br />
5 Recommendations<br />
5.1 Recommendations on packaging, transport and storage<br />
In the accompanying documentation or on the containers, the manufacturer shall give<br />
information as to transport and storage.<br />
At least the following shall be indicated: type of storage (container, tank, etc.), minimum and<br />
maximum temperature for transport and storage. In case of combustible components or other<br />
potentially dangerous substances the instructions shall contain indications about limitations<br />
and/or conditions for handling, transport and storage.<br />
5.2 Recommendations on use, maintenance and repair<br />
The assessment of the fitness for use is based on the assumption that necessary maintenance<br />
and repair, if required, is carried out in accordance with the manufacturer’s instructions during<br />
the assumed intended working life.<br />
The topcoat, where necessary, shall protect the reactive coating from moisture and other<br />
environmental influences. Therefore it shall always be kept in a proper state. In case of an<br />
execution without topcoat the control shall refer to the reactive coating. If the maintenance work<br />
related to the reactive coating or the topcoating is necessary, the manufacturer’s instructions<br />
shall be respected.<br />
On behalf of the Catalonia Institute of Construction Technology.<br />
Barcelona, 17 January 2013<br />
Anton Maria Checa Torres<br />
General Manager, ITeC