www .feig e.co m - Haver Filling Systems, Inc.

Series 30
The concept
An automatic filling machine of the type range 30 for the filling of drums, cans/pails or even palletised containers will soon pay off.
These machines do without the wide ranging combinations of variants which enable the integration of the electro-pneumatic control with
the keypad into one compact stainless steel control cabinet. The control cabinet is directly connected to the machine – completely wired
and hosed. The frame construction, appropriate for lorry transport, guarantees low shipping cost and minimal installation work on site.
The same applies to hazardous area application. In this case, the control cabinet is purged (pressurisation, EExp, in conformity
with ATEX regulation). Thus, no cable or hose laying is required!
Automatic Drum Filling Machine Type 31 Type 32 Type 33
Automatic Drum Filling Machine with one, two or three working stations
Feeding, exact positioning, filling (W&M approved filling) and removal for out-feed of one drum at a time.
And it is up to you: The drum can even be de-bunged, re-bunged or purged.
A double filling station (pre- and final filling) is also available to increase the output.
Automatic Pail/Can Filling Machine Type 34
Automatic Pail/Can Filling Machine with three or four step lateral conveyor
For in-feed and out-feed your containers are transported with a roller conveyor. A lateral conveyor between the roller conveyors exactly
positions the containers to the filling station where they are filled as per W&M legislation.
Additional working steps may be effected at the other positions: removal of dust caps, inerting, bunging of caps, placing and pressing
in of lids.
In order to increase the output the filling can be effected with product flow control.
The filling valve
Safety functions
The weigh scale
• Filling valve
diameter
according to
– Filling opening
– Viscosity
– Flow rate
– Double acting actuator –
air-to-open
– Pressure balanced valve
– Leakage monitoring of
sealing area of valve
stem guide
– Fill level check
– Misalignment
protection
– Tare check
– Ground/Earth check
– Flow check
– Fill time check
– Tolerance check
• 255 Product files,
expandable
• Protocol of
weighing results
and statistics
• Aseptic
• Minimum dead
space
• Heated
filling
valves
• Alphanumeric entry
through prompting
• Storage of
operation data
• Material
– Stainless steel
– Teflon
– Hastelloy
– Titanium/Nickel
• Multistage
dosing
• Proportional
Dosing
Filling valve
with quick change valve mount
Stainless steel operator panel
with integrated operating elements
• Label printer
protocol printer
• Scanner
• Measuring device
Load cell
Mass flow meter
Type 31
• Drum Filling Machine with one working station
Type 32
• Drum Filling Machine with two working stations
• Type 33 Drum Filling Machine with three working stations
• Pail Filling Machine with three step lateral conveyor
Type 34
Accessories
• Pressure surges reduction
system for control of the
product flow
• Raise-by-weight
through weight
increase
• Gas hood
for exhaust of filling gas
• Drip scoop
activated by lance stroke
• Inert gas purging
Bunging unit
• With automatic torque
adjustment
• Monitoring of bunging
• Travel limit
• Adjustable
descending
pressure
• Adjustable torque
from 10 to 50 Nm
• Anticlockwise/
clockwise
• Self-aligning
bunging head
• Adjustment of lateral
off-set, all side
• Product hose
with direct filling valve
connection
• Drain funnel for valve
purging inside the
system (CIP)
• Drip collecting device
pneumatically operated
• Manual bunging and sealing
station
• Earthing device for discharging
of electro-static charge
• Gas hood
• Adjustment of
angular off-set,
all side
• Handling of your
standard plugs
• Bunging head
• Above-surface filling valve
with diffuser disk
• Pail denester
• Lid placer
Filling modes:
Depending on the
filling product and
the container type
different filling
modes are used:
Below-surface
for products which
produce foam or
explosive gas
during filling
Above-surface
for uncritical
products which
are filled in open
top containers
Below-bunghole
for uncritical
products which are
filled in bung-type
containers
Technical data Type 31 Type 32 Type 33 Type 33
Drum type
bung-type drums made of steel (EN210/EN 13007) or plastic (EN 12707/EN12709)
Drum volume/W&M approved filling range
50 l, 200 l - 250 l / 10 - 300 kg
Characteristics filling only with debunging with pre-filling with debunging/bunging
Nominal output for 200 l drums approx. 40/h approx. 60/h approx. 110/h approx. 60/h
Technical data Type 34.2 Type 34.5 Type 34.1 Type 34.3
Type of container pail can
W&M approved filling range
2,5 - 30 kg
Characteristics above-surface product fl ow control below-surface below bunghole
Nominal output for 20 l containers approx. 300/h approx. 500/h approx. 180/h approx. 200/h
2 3
4