SCREAMIN' PRO RACING PARTS EAGLE® - Harley-Davidson

a. ScrEamIn’ EaglE ® rocKEr BoX BolT
raTchETIng WrEnch
This high-quality wrench simplifies working on the rocker
box while the engine is mounted in the motorcycle’s frame.
This tool features a low-profile design to allow access to the
tight spaces between the frame and the engine. The wrench
has a long handle for increased reach, a replaceable bit
and a reversible ratcheting action so the socket head cap
screw can be ratcheted in or out. The comfortable soft vinyl
grip with Screamin’ eagle ® logo protects the engine from
scratches.
94057-09 $34.95
For use on all Harley-Davidson ® Big Twin rocker box covers.
a
B
c
B. ScrEamIn’ EaglE loWEr rocKEr BoX WrEnch
This quality long-handled wrench is designed to simplify
installation and removal of the lower rocker box on Twin
Cam engines. The special 7/16" socket is shaped to reach
these confined areas. The comfortable soft vinyl grip with
Screamin’ eagle logo protects the engine from scratches.
94074-09 $25.95
For use on Twin Cam engines.
c. ScrEamIn’ EaglE InTaKE manIFolD WrEnch
This reversible ratcheting box wrench simplifies and speeds
up the installation and removal of the intake manifold socket
head cap screws used on Big Twin engines. The comfortable
soft vinyl grip with Screamin’ eagle logo protects the engine
from scratches.
94063-09 $34.95
For use on all Big Twin engines.
D. ScrEamIn’ EaglE FlyWhEEl ShaFT
raTchET WrEnch
This high-quality ratcheting tool allows technician to manually
rotate the flywheel of the engine to check cam timing,
and to inspect valve-to-valve, piston-to-valve and piston-topiston
clearances. Designed to easily slip over the output
crankshaft spline, the wrench features a simple-to-use
finger-operated lever to reverse the ratcheting direction.
94038-09 24 Tooth Spline. $54.95
For use on ’06-later Dyna ® and ’07-later Touring
and Softail ® models.
94088-09 Sportster ® Spline. $39.95
For use on ’72-later XL and Xr models.
94089-09 10 Tooth Spline. $39.95
For use on ’72-’06 Big Twin engines (except
’06 Dyna models).
E. ScrEamIn’ EaglE TorQuE anglE gaugE
This tool allows you to use the same precise assembly techniques
used at the factory. Many fasteners on the engine
should be tightened to an initial torque value and then turned
an additional prescribed angle to ensure that the fastener
has the appropriate amount of “stretch” and attains the
required clamp load. Tightening fasteners by torque specification
alone can result in insufficient or over-tightening
because of nicked or dirty threads. The easy-to-read dial face
provides precise measurement, and the 3/8" drive makes
this tool compact and easy to use in most applications.
94147-10 $39.95
For use on applications where torque angle measurements
are specified during assembly, e.g. head bolts.
F. ScrEamIn’ EaglE o2 SEnSor SocKET
This cut-away socket is designed to clear the wire lead and
simplify the removal or installation of the oxygen sensor on
closed loop fuel-injected models. Manufactured to withstand
the installation torque requirements, the socket features a
3/8" drive receiver.
94136-09 $35.95
For use on ’06-later XL models, ’06-’11 VrSC, Dyna and
Softail models, and ’06-’09 Touring and Trike models.
93980-10 $19.95
For use on ’12-later VrSC, Dyna and Softail models, and
’10-later Touring and Trike models.
g. ScrEamIn’ EaglE auTomaTIc comPrESSIon
rElEaSE rEmoVal Tool
Socket designed for removal and installation of Harley-
Davidson Automatic Compression release solenoid.
94048-09 $39.95
For all Harley-Davidson models equipped with Screamin’
eagle Automatic Compression release.
ScrEamIn’ EaglE WrEnchES
B. ScrEamIn’ EaglE loWEr rocKEr
BoX WrEnch
D. ScrEamIn’ EaglE FlyWhEEl ShaFT
raTchET WrEnch
a. ScrEamIn’ EaglE rocKEr BoX BolT
raTchETIng WrEnch
c. ScrEamIn’ EaglE InTaKE
manIFolD WrEnch
E. ScrEamIn’ EaglE TorQuE anglE gaugE
102 accESSorIES
SPeCIALTy TOOLS
F. ScrEamIn’ EaglE o2 SEnSor
SocKET (93980-10 ShoWn)
g. ScrEamIn’ EaglE auTomaTIc
comPrESSIon rElEaSE rEmoVal Tool