HAHN+KOLB-Toolcatalog 2011/12 – Metal Cutting Tools

Drilling tools
Indexable tools for drilling, countersinking and counterboring
(continued)
Coating coated uncoated
Walter designation WAP 20 WKP 35 WXP 40 WAK 15 WKP 25 WK 40
Standard description
HC - P20
HC - P35
HC - P40
HC - K15
HC - K25
HW - S35
HC - K30
HC - K35
HC - M30
HC - P15
HW - N30
HC - S30
Material group
Ø range Indexable Dimensions and angle
inserts
l 1 x l 2 s α° η° 11210 11210 11210 11210 11210 11210
mm Type/Size mm mm Ident. No. U. pr. E Ident. No. U. pr. E Ident. No. U. pr. E Ident. No. U. pr. E Ident. No. U. pr. E Ident. No. U. pr. E
P 28467 -
411 O. R. 412 O. R. 413 O. R. 414 (O. R.) 415 (O. R.) – –
S.4
31,0
-36,0
P 28469 -
S.4
11,0 x 11,0 3,97 11 96
– – 422 O. R. 423 O. R. – – – – 426 O. R.
P 28475 -
441 O. R. 442 O. R. 443 O. R. – – – – – –
S.4
P 28467 -
511 O. R. 512 (O. R.) 513 (O. R.) 514 (O. R.) 515 (O. R.) – –
37,0
-42,0
S.5
P 28469 -
S.5
12,7 x 12,7 4,76 11 96
– – 522 O. R. 523 O. R. – – – – 526 (O. R.)
P 28475 -
541 (O. R.) 542 O. R. 543 O. R. – – – – – –
S.5
P 28467-
611 O. R. 612 (O. R.) 613 O. R. 614 (O. R.) 615 (O. R.) – –
S.6
43,0 P 28469-
15,0 x 15,0 4,76 11 96
– – 622 (O. R.) 623 O. R. – – – – 626 (O. R.)
-50,0 S.6
P 28475-
641 O. R. 642 O. R. 643 O. R. – – – – – –
S.6
P 28467-
711 O. R. 712 (O. R.) 713 O. R. 714 (O. R.) 715 (O. R.) – –
S.7
51,0 P 28469-
17,6 x 17,6 5,56 11 96
– – 722 (O. R.) 723 O. R. – – – – 726 (O. R.)
-58,0 S.7
P 28475-
741 O. R. 742 O. R. 743 O. R. – – – – – –
S.7
j For cutting value recommendations see www.hahn-kolb.de/Downloads/Schnittwertempfehlungen. Prod. Gr. 162
Metal-cutting tools
Continued next page
Selection aid
indexable inserts geometries / application
Indexable inserts geometries Use Indexable inserts geometries Use
LCMX -B57 U 6° cutting angle
U long-chipping materials P28467 U universal geometry for steel and cast metal U also for medium to unfavourable conditions
U short chip groove
U high chip groove back
U corrugated sheet section
U high chip deformation
U feed rate depending on material machining
U circumference ground
(oblique entry or exit, drilling of diagonal holes,
unstable tool or work piece clamping)
U for precisely drilled holes
LCMX
LCMX
-D57 U 12° cutting angle
U medium chip groove
U medium groove back
-E57 U 15° cutting angle
U wide chip groove
U flat groove back
U general steel processing
U medium feed rate
U short chipping materials
U high feed rate
P28469 U soft-cutting geometry
U wave-shaped chip breaker
U circumference ground
P28475 U favourable, sintered universal geometry for
steel and cast metal machining
U especially for soft types of steel
U also suitable for aluminium and stainless
steels with a tendency to long chipping
U for precisely drilled holes
U also for medium to unfavourable conditions
(oblique entry or exit, drilling of diagonal holes,
unstable tool or workpiece clamping)
2011/12
85