LANTEK User Manual - Ideal Industries
LANTEK User Manual - Ideal Industries LANTEK User Manual - Ideal Industries
Chapter 5 Fiber Optics Cable Field Calibration and Testing A test result screen will appear at the completion of the test procedure. LENGTH TEST (DUAL HANDSET) Figure 5-8: Loopback Test Results Screen Configuration Setup for Length Testing 1. With the appropriate test adapter on the Display Handset and the appropriate test adapter on the Remote Handset, connect one end of the near end launch cable leads to the TX and RX connectors on the Display Handset adapter. 2. Connect the other end of the launch cable leads to the patch panel that connects to the fiber under test. 3. Connect one end of the far end launch cable leads to the TX and RX connectors on the Remote Handset adapter. 4. Connect the other end of the far end launch cable to the wall plate (fiber cable under test). 5. Check all connections to ensure proper contact. Upon completion, you are ready to perform a fiber test. Figure 5-9: Configuration for Dual Handset Testing 6. Press the LENGTH key on the Display Handset or select Analyze on the Ready screen and press ENTER. 7. Then, select Length, and press ENTER. 8. At the completion of the test procedure, a test result screen will appear. 5-9
Chapter 5 Fiber Optics Cable Field Calibration and Testing DUAL WAVELENGTH ATTENUATION TEST SETUP 1. With the appropriate test adapter on the Display Handset and the appropriate test adapter on the Remote Handset, connect one end of the near end launch cable leads to the TX and RX connectors on the Display Handset adapter. 2. Connect the other end of the launch cable leads to the patch panel that connects to the fiber under test. 3. Connect one end of the far end launch cable leads to the TX and RX connectors on the Remote Handset adapter. 4. Connect the other end of the far end launch cable to the wall plate (fiber cable under test). 5. Check all connections to ensure proper contact. Upon completion, you are ready to perform a fiber test. Figure 5-10: Dual Wavelength Attenuation Testing Configuration DUAL WAVELENGTH ATTENUATION TESTING 1. Press AUTOTEST on the Display Handset or Remote Handset to begin the test, or select Analyze on the Display Handset Ready Screen and select Attenuation in the Analyze screen . 2. When the Autotest is completed, the results of the test are displayed. 3. Use the UP/DOWN ARROW Keys to view test results of different wavelengths. Screen Results thru Autotest process Screen Results thru Analyze process Figure 5-11: Dual Wavelength Attenuation Test Result Screens 5-10
- Page 44 and 45: Chapter 3 Structured Cable Field Ca
- Page 46 and 47: Chapter 3 Structured Cable Field Ca
- Page 48 and 49: Chapter 3 Structured Cable Field Ca
- Page 50 and 51: Chapter 3 Structured Cable Field Ca
- Page 52 and 53: Chapter 3 Structured Cable Field Ca
- Page 54 and 55: Chapter 3 Structured Cable Field Ca
- Page 56 and 57: Chapter 3 Structured Cable Field Ca
- Page 58 and 59: Chapter 3 Structured Cable Field Ca
- Page 60 and 61: Chapter 3 Structured Cable Field Ca
- Page 62 and 63: Chapter 3 Structured Cable Field Ca
- Page 64 and 65: Chapter 3 Structured Cable Field Ca
- Page 66 and 67: Chapter 3 Structured Cable Field Ca
- Page 68 and 69: Chapter 3 Structured Cable Field Ca
- Page 70 and 71: Chapter 3 Structured Cable Field Ca
- Page 72 and 73: Chapter 3 Structured Cable Field Ca
- Page 74 and 75: Chapter 3 Structured Cable Field Ca
- Page 76 and 77: Chapter 3 Structured Cable Field Ca
- Page 78 and 79: Chapter 3 Structured Cable Field Ca
- Page 80 and 81: Chapter 3 Structured Cable Field Ca
- Page 82 and 83: CHAPTER 4 COAX CABLE FIELD CALIBRAT
- Page 84 and 85: Chapter 4 Coax Cable Field Calibrat
- Page 86 and 87: CHAPTER 5 FIBER OPTICS CABLE FIELD
- Page 88 and 89: Chapter 5 Fiber Optics Cable Field
- Page 90 and 91: Chapter 5 Fiber Optics Cable Field
- Page 92 and 93: Chapter 5 Fiber Optics Cable Field
- Page 96 and 97: Chapter 5 Fiber Optics Cable Field
- Page 98 and 99: Chapter 5 Fiber Optics Cable Field
- Page 100 and 101: Chapter 6 Fiber Optics Diagnostics
- Page 102 and 103: Chapter 6 Fiber Optics Diagnostics
- Page 104 and 105: Chapter 6 Fiber Optics Diagnostics
- Page 106 and 107: Chapter 6 Fiber Optics Diagnostics
- Page 108 and 109: Chapter 6 Fiber Optics Diagnostics
- Page 110 and 111: Chapter 6 Fiber Optics Diagnostics
- Page 112 and 113: CHAPTER 7 LANTEK REPORTER SOFTWARE
- Page 114 and 115: Chapter 7 LANTEK REPORTER Software
- Page 116 and 117: Chapter 7 LANTEK REPORTER Software
- Page 118 and 119: Chapter 7 LANTEK REPORTER Software
- Page 120 and 121: Chapter 7 LANTEK REPORTER Software
- Page 122 and 123: Chapter 7 LANTEK REPORTER Software
- Page 124 and 125: Chapter 7 LANTEK REPORTER Software
- Page 126 and 127: Chapter 7 LANTEK REPORTER Software
- Page 128 and 129: Chapter 7 LANTEK REPORTER Software
- Page 130 and 131: Chapter 7 LANTEK REPORTER Software
- Page 132 and 133: Chapter 7 LANTEK REPORTER Software
- Page 134 and 135: Chapter 7 LANTEK REPORTER Software
- Page 136 and 137: Chapter 7 LANTEK REPORTER Software
- Page 138 and 139: Chapter 7 LANTEK REPORTER Software
- Page 140 and 141: APPENDIX A SAFETY PRECAUTIONS HANDL
- Page 142 and 143: APPENDIX B CUSTOMER SUPPORT CUSTOME
Chapter 5<br />
Fiber Optics Cable Field Calibration and Testing<br />
DUAL WAVELENGTH ATTENUATION TEST SETUP<br />
1. With the appropriate test adapter on the Display Handset and the appropriate test<br />
adapter on the Remote Handset, connect one end of the near end launch cable<br />
leads to the TX and RX connectors on the Display Handset adapter.<br />
2. Connect the other end of the launch cable leads to the patch panel that connects<br />
to the fiber under test.<br />
3. Connect one end of the far end launch cable leads to the TX and RX connectors on<br />
the Remote Handset adapter.<br />
4. Connect the other end of the far end launch cable to the wall plate (fiber cable<br />
under test).<br />
5. Check all connections to ensure proper contact. Upon completion, you are ready to<br />
perform a fiber test.<br />
Figure 5-10: Dual Wavelength Attenuation Testing Configuration<br />
DUAL WAVELENGTH ATTENUATION TESTING<br />
1. Press AUTOTEST on the Display Handset or Remote Handset to begin the test, or<br />
select Analyze on the Display Handset Ready Screen and select Attenuation in the<br />
Analyze screen .<br />
2. When the Autotest is completed, the results of the test are displayed.<br />
3. Use the UP/DOWN ARROW Keys to view test results of different wavelengths.<br />
Screen Results thru Autotest process<br />
Screen Results thru Analyze process<br />
Figure 5-11: Dual Wavelength Attenuation Test Result Screens<br />
5-10