LANTEK User Manual - Ideal Industries
LANTEK User Manual - Ideal Industries LANTEK User Manual - Ideal Industries
Chapter 3 Structured Cable Field Calibration and Testing TEST SEQUENCE When the AUTOTEST button is pressed, the following actions occur: 1. The DH firsts attempt to communicate with the RH (Remote Handset) using one correctly wired pair. If it is unable to establish communication, the DH will display a message that it is looking for the RH and continue trying until the Autotest is manually canceled or the RH is found. 2. Once communication with the RH is established, its serial number is checked to see if current field calibration data exists. If a field calibration has not been performed in the last 7 days with the RH unit, the Autotest will be aborted and a “Calibration Required” message will display. 3. If the serial number is valid, the DH will proceed with the specified Autotest. The first test performed in most Autotests is the Wire Map for twisted pair cable types. 4. After running the Wire Map test, Autotest runs the remaining tests specified for the currently selected cable type. You have the option of specifying (in Autotest Preferences) that testing halt after any failed test or proceed through the entire Autotest series regardless of test failures. 5. Once an Autotest has been completed, all of the test data can be reviewed, saved, and printed. ‣ The test results for the last Autotest are held in non-volatile memory and available for review or storage, even after power is cycled off and back on. ‣ The last Autotest results remain in non-volatile memory until they are either replaced by new test results, the memory is cleared, or any Analyze test is performed. SETTING AUTOTEST PREFERENCES 1. Select the Preferences on the Ready screen. The Preferences screen appears. 2. Select Autotest Preferences. The Autotest Preference screen appears. 3. Press the ARROW keys to highlight the desired option. 4. Press to activate or deactivate an option. 5. Press ENTER to accept the selected Autotest Preferences or press ESCAPE to exit this screen without making changes. RUNNING AUTOTEST AND UNDERSTANDING RESULTS Autotest performs comprehensive tests using programmed testing limits. An overall pass or fail is displayed along with individual test results. Before beginning Autotesting, connect the Display and Remote handsets to the cable or link to be tested. 1. Press AUTOTEST. During the Autotest, the handset unit will display a progress screen. 2. If the RH unit is not found, a “Searching for Remote Handset” warning message is displayed on the DH. Press ESCAPE to cancel the test and return to the Ready screen. 3. If the RH is found, Autotest compares the cable test readings to standards for the cable type selected and issues pass/fail statements for each test. 4. When the Autotest is completed, an overall result of pass or fail is displayed at the top right of the test information columns. Results for individual tests are displayed opposite each test name. 3-12
Chapter 3 Structured Cable Field Calibration and Testing 5. To begin another Autotest, press AUTOTEST. If results from the current test have not been saved, you will be prompted to discard or save the current test results before the next Autotest will run. Note: The tester also performs real time Analyze testing that enables you to troubleshoot problem areas. If Autotest results indicate a failure, refer to the Analyze Testing section for further details. INTERPRETING AUTOTEST RESULTS Pass/Fail Reporting The overall Autotest result is displayed at the top right of the Autotest display screen. Individual Autotest results are displayed to the right of each test. Figure 3-2: Typical Overall Autotest Results Screen Table 3-2: Test Result Symbols Symbol Overall Autotest Result Overall test result is a pass if each individual test is a pass or a pass*. Overall test result is a fail if one or more individual test is either a fail or a fail*. Viewing Current Autotest Results Results can be viewed at completion of the test sequence or saved for later viewing. 1. Press the ARROW keys to highlight the desired test. 2. Press ENTER to view test results. Figure 3-3: Typical Individual Autotest Results Screen 3-13
- Page 4 and 5: TABLE OF CONTENTS OPERATIONAL NOTES
- Page 6 and 7: TROUBLESHOOTING 10/100/1000 BASE-T
- Page 8 and 9: Headers and Footers Command .......
- Page 10 and 11: OPERATIONAL NOTES, CAUTIONS, AND WA
- Page 12 and 13: Chapter 1 Your Cable Tester PRODUCT
- Page 14 and 15: Chapter 1 Your Cable Tester Table 1
- Page 16 and 17: Chapter 1 Your Cable Tester Item DH
- Page 18 and 19: Chapter 1 Your Cable Tester HARD AN
- Page 20 and 21: Chapter 1 Your Cable Tester DISPLAY
- Page 22 and 23: Chapter 1 Your Cable Tester OVERVIE
- Page 24 and 25: Chapter 2 Test Setup Procedures AUT
- Page 26 and 27: Chapter 2 Test Setup Procedures TIM
- Page 28 and 29: Chapter 2 Test Setup Procedures Fig
- Page 30 and 31: Chapter 2 Test Setup Procedures PAC
- Page 32 and 33: Chapter 2 Test Setup Procedures TEM
- Page 34 and 35: Chapter 2 Test Setup Procedures Tab
- Page 36 and 37: Chapter 2 Test Setup Procedures Sav
- Page 38 and 39: Chapter 2 Test Setup Procedures OTH
- Page 40 and 41: Chapter 2 Test Setup Procedures Edi
- Page 42 and 43: Chapter 2 Test Setup Procedures ACT
- Page 44 and 45: Chapter 3 Structured Cable Field Ca
- Page 46 and 47: Chapter 3 Structured Cable Field Ca
- Page 48 and 49: Chapter 3 Structured Cable Field Ca
- Page 50 and 51: Chapter 3 Structured Cable Field Ca
- Page 52 and 53: Chapter 3 Structured Cable Field Ca
- Page 56 and 57: Chapter 3 Structured Cable Field Ca
- Page 58 and 59: Chapter 3 Structured Cable Field Ca
- Page 60 and 61: Chapter 3 Structured Cable Field Ca
- Page 62 and 63: Chapter 3 Structured Cable Field Ca
- Page 64 and 65: Chapter 3 Structured Cable Field Ca
- Page 66 and 67: Chapter 3 Structured Cable Field Ca
- Page 68 and 69: Chapter 3 Structured Cable Field Ca
- Page 70 and 71: Chapter 3 Structured Cable Field Ca
- Page 72 and 73: Chapter 3 Structured Cable Field Ca
- Page 74 and 75: Chapter 3 Structured Cable Field Ca
- Page 76 and 77: Chapter 3 Structured Cable Field Ca
- Page 78 and 79: Chapter 3 Structured Cable Field Ca
- Page 80 and 81: Chapter 3 Structured Cable Field Ca
- Page 82 and 83: CHAPTER 4 COAX CABLE FIELD CALIBRAT
- Page 84 and 85: Chapter 4 Coax Cable Field Calibrat
- Page 86 and 87: CHAPTER 5 FIBER OPTICS CABLE FIELD
- Page 88 and 89: Chapter 5 Fiber Optics Cable Field
- Page 90 and 91: Chapter 5 Fiber Optics Cable Field
- Page 92 and 93: Chapter 5 Fiber Optics Cable Field
- Page 94 and 95: Chapter 5 Fiber Optics Cable Field
- Page 96 and 97: Chapter 5 Fiber Optics Cable Field
- Page 98 and 99: Chapter 5 Fiber Optics Cable Field
- Page 100 and 101: Chapter 6 Fiber Optics Diagnostics
- Page 102 and 103: Chapter 6 Fiber Optics Diagnostics
Chapter 3<br />
Structured Cable Field Calibration and Testing<br />
5. To begin another Autotest, press AUTOTEST. If results from the current test have<br />
not been saved, you will be prompted to discard or save the current test results<br />
before the next Autotest will run.<br />
Note: The tester also performs real time Analyze testing that enables you to<br />
troubleshoot problem areas. If Autotest results indicate a failure, refer to the Analyze<br />
Testing section for further details.<br />
INTERPRETING AUTOTEST RESULTS<br />
Pass/Fail Reporting<br />
The overall Autotest result is displayed at the top right of the Autotest display screen.<br />
Individual Autotest results are displayed to the right of each test.<br />
Figure 3-2: Typical Overall Autotest Results Screen<br />
Table 3-2: Test Result Symbols<br />
Symbol<br />
Overall Autotest Result<br />
Overall test result is a pass if each individual test is a pass or a pass*.<br />
Overall test result is a fail if one or more individual test is either a fail or a fail*.<br />
Viewing Current Autotest Results<br />
Results can be viewed at completion of the test sequence or saved for later viewing.<br />
1. Press the ARROW keys to highlight the desired test.<br />
2. Press ENTER to view test results.<br />
Figure 3-3: Typical Individual Autotest Results Screen<br />
3-13