LANTEK User Manual - Ideal Industries
LANTEK User Manual - Ideal Industries LANTEK User Manual - Ideal Industries
Chapter 3 Structured Cable Field Calibration and Testing GG45 – TROUBLESHOOTING A field calibration should be performed prior to implementing a test of the GG45 cabling system. This process will ensure (1) synchronizing of the units, (2) qualifying (testing) of the patchcords and (3) gathering of loss data regarding the patchcords and mated connections. The equipment required for a GG45 calibration procedure is: ‣ Display Handset ‣ Remote Handset ‣ GG45 Calibration Adapters (Two adapters joined by a short segment of Category 7 cable) ‣ GG45 Calibration Load Terminator (100Ω Jack) ‣ GG45 Permanent Link Adapters (A set of two adapters, each with a patchcord (approximately 2 meters) soldered to the adapter at one end and a GG45 Category 7 plug at the opposite end) TESTING A GG45 CABLING SYSTEM Figure 3-1: Typical Configuration for GG45 Cable Testing Typical configuration for testing has the DH unit and RH unit connected to the GG45 Permanent Link Adapters. The cable under test is connected at the Category 7 plug end of both the DH and RH ends. 3-4
Chapter 3 Structured Cable Field Calibration and Testing FIELD CALIBRATION - PATCHCORD TESTING This Field Calibration is a 4-step process. Steps 1 and 2 are performed with the hybrid (RJ45 Plug to RJ45-TIA-Reference-Jack) patchcords connected to the Handsets using the kit’s mini patchcord. Steps 3 and 4 are performed with open-ended hybrid patchcords (Only one end connected to the Handsets). To calibrate the tester, perform the following: Step 1 ‣ Connect the Category 5e/6 – RJ45 adapters to the Display Handset (DH) and Remote Handset (RH). Power both units on. ‣ Connect the RJ45 plug of the first hybrid patchcord to the Remote Handset (RH). Using the RJ45 mini patchcord attach the DH RJ45-TIA Reference Jack end of the hybrid patchcord to one end of the mini patchcord and then connect the other end of the mini patchcord to the Display Handset (DH). Note: Patchcords can vary in length. The most common length used is the 2-meter length patchcords. ‣ From the DH Ready Screen, select Field Calibration. The Calibration screen appears. ‣ From the RH, press AUTOTEST to perform the first step of the calibration process. At the completion of step 1, disconnect the mini patchcord and hybrid patchcord from the RH and DH. Step 2 ‣ Connect the RJ45 plug of the second hybrid patchcord to the Display Handset (DH). Using the RJ45 mini patchcord attach the DH RJ45-TIA Reference Jack end of the hybrid patchcord to one end of the mini patchcord and then connect the other end of the mini patchcord to the Remote Handset (RH). ‣ From the DH Field Calibration screen, select START or press AUTOTEST from the RH to perform the second step of the calibration process. ‣ At the completion of step 2, disconnect the mini patchcord. 3-5
- Page 2 and 3: LANTEK TM CABLE TESTER USER’S GUI
- Page 4 and 5: TABLE OF CONTENTS OPERATIONAL NOTES
- Page 6 and 7: TROUBLESHOOTING 10/100/1000 BASE-T
- Page 8 and 9: Headers and Footers Command .......
- Page 10 and 11: OPERATIONAL NOTES, CAUTIONS, AND WA
- Page 12 and 13: Chapter 1 Your Cable Tester PRODUCT
- Page 14 and 15: Chapter 1 Your Cable Tester Table 1
- Page 16 and 17: Chapter 1 Your Cable Tester Item DH
- Page 18 and 19: Chapter 1 Your Cable Tester HARD AN
- Page 20 and 21: Chapter 1 Your Cable Tester DISPLAY
- Page 22 and 23: Chapter 1 Your Cable Tester OVERVIE
- Page 24 and 25: Chapter 2 Test Setup Procedures AUT
- Page 26 and 27: Chapter 2 Test Setup Procedures TIM
- Page 28 and 29: Chapter 2 Test Setup Procedures Fig
- Page 30 and 31: Chapter 2 Test Setup Procedures PAC
- Page 32 and 33: Chapter 2 Test Setup Procedures TEM
- Page 34 and 35: Chapter 2 Test Setup Procedures Tab
- Page 36 and 37: Chapter 2 Test Setup Procedures Sav
- Page 38 and 39: Chapter 2 Test Setup Procedures OTH
- Page 40 and 41: Chapter 2 Test Setup Procedures Edi
- Page 42 and 43: Chapter 2 Test Setup Procedures ACT
- Page 44 and 45: Chapter 3 Structured Cable Field Ca
- Page 48 and 49: Chapter 3 Structured Cable Field Ca
- Page 50 and 51: Chapter 3 Structured Cable Field Ca
- Page 52 and 53: Chapter 3 Structured Cable Field Ca
- Page 54 and 55: Chapter 3 Structured Cable Field Ca
- Page 56 and 57: Chapter 3 Structured Cable Field Ca
- Page 58 and 59: Chapter 3 Structured Cable Field Ca
- Page 60 and 61: Chapter 3 Structured Cable Field Ca
- Page 62 and 63: Chapter 3 Structured Cable Field Ca
- Page 64 and 65: Chapter 3 Structured Cable Field Ca
- Page 66 and 67: Chapter 3 Structured Cable Field Ca
- Page 68 and 69: Chapter 3 Structured Cable Field Ca
- Page 70 and 71: Chapter 3 Structured Cable Field Ca
- Page 72 and 73: Chapter 3 Structured Cable Field Ca
- Page 74 and 75: Chapter 3 Structured Cable Field Ca
- Page 76 and 77: Chapter 3 Structured Cable Field Ca
- Page 78 and 79: Chapter 3 Structured Cable Field Ca
- Page 80 and 81: Chapter 3 Structured Cable Field Ca
- Page 82 and 83: CHAPTER 4 COAX CABLE FIELD CALIBRAT
- Page 84 and 85: Chapter 4 Coax Cable Field Calibrat
- Page 86 and 87: CHAPTER 5 FIBER OPTICS CABLE FIELD
- Page 88 and 89: Chapter 5 Fiber Optics Cable Field
- Page 90 and 91: Chapter 5 Fiber Optics Cable Field
- Page 92 and 93: Chapter 5 Fiber Optics Cable Field
- Page 94 and 95: Chapter 5 Fiber Optics Cable Field
Chapter 3<br />
Structured Cable Field Calibration and Testing<br />
FIELD CALIBRATION - PATCHCORD TESTING<br />
This Field Calibration is a 4-step process. Steps 1 and 2 are performed with the hybrid<br />
(RJ45 Plug to RJ45-TIA-Reference-Jack) patchcords connected to the Handsets using<br />
the kit’s mini patchcord. Steps 3 and 4 are performed with open-ended hybrid<br />
patchcords (Only one end connected to the Handsets).<br />
To calibrate the tester, perform the following:<br />
Step 1<br />
‣ Connect the Category 5e/6 – RJ45 adapters to the Display Handset (DH) and<br />
Remote Handset (RH). Power both units on.<br />
‣ Connect the RJ45 plug of the first hybrid patchcord to the Remote Handset (RH).<br />
Using the RJ45 mini patchcord attach the DH RJ45-TIA Reference Jack end of the<br />
hybrid patchcord to one end of the mini patchcord and then connect the other<br />
end of the mini patchcord to the Display Handset (DH).<br />
Note: Patchcords can vary in length. The most common length used is the 2-meter<br />
length patchcords.<br />
‣ From the DH Ready Screen, select Field Calibration. The Calibration screen<br />
appears.<br />
‣ From the RH, press AUTOTEST to perform the first step of the calibration<br />
process. At the completion of step 1, disconnect the mini patchcord and hybrid<br />
patchcord from the RH and DH.<br />
Step 2<br />
‣ Connect the RJ45 plug of the second hybrid patchcord to the Display Handset<br />
(DH). Using the RJ45 mini patchcord attach the DH RJ45-TIA Reference Jack<br />
end of the hybrid patchcord to one end of the mini patchcord and then connect<br />
the other end of the mini patchcord to the Remote Handset (RH).<br />
‣ From the DH Field Calibration screen, select START or press AUTOTEST from<br />
the RH to perform the second step of the calibration process.<br />
‣ At the completion of step 2, disconnect the mini patchcord.<br />
3-5