LANTEK User Manual - Ideal Industries
LANTEK User Manual - Ideal Industries LANTEK User Manual - Ideal Industries
Chapter 2 Test Setup Procedures AUTOTEST PREFERENCES Autotest can be set to automatically stop on the first failed test, as well as to save, and name test results at the completion of each test series. 1. Select Autotest Preferences on the Preferences screen. Press ENTER. The Autotest Preference screen appears. 2. Press the UP/DOWN ARROW keys to highlight the desired option. 3. Press to activate or deactivate the highlighted option. Figure 2-3: Autotest Preference Screen 4. Press ENTER to save or ESCAPE to exit. Table 2-1: Autotest Preference Options Option Simple Cable ID Stop on Fail AutoSave Save Graphs Auto Increment Confirm Delete Disable Fiber Autotest Length Enable 606A Dim Backlight Action Assign a fixed alpha value for the Cable ID. Autotest aborts at the first failed test. Otherwise, Autotest continues until all tests are completed, regardless of results. Note: If a wire map cannot be completed due to gross miss-wiring, the Autotest may abort regardless of the setting of this preference. Autotest automatically names and saves any passed AUTOTEST results. Failed tests are not automatically saved. Displaying graphs on the DH requires data to be transferred from the RH to the DH. To save time during testing, do not select this option. Note: De-selecting this option will not allow graphs to be loaded to the PC software or printed on certification reports. Autotest automatically increments Single and Double Cable ID test counters. Activate request to confirm any Delete operation. Disable or enable fiber Autotest length procedure. Enable 606-A Cable ID naming standard. Toggle illumination of screen display backlighting during Autotest. 2-2
Chapter 2 Test Setup Procedures Table 2-1: Autotest Preference Options (continued) Option Enable Tera to Tera Mode Enable Wiremap on Failed Autotest Action LANTEK is set to default with Tera-to-Tera enable mode. In this mode, LANTEK firmware assumes that there is Tera-to-Tera patchcords connected and will treat an Autotest as a Cat 7 Autotest. If unselected, LANTEK firmware will assume that there is Tera-to-RJ45 patchcords attached and the Autotest will be treated as a Cat 6 Autotest. Mode dictates whether or not the LANTEK will automatically enter the advanced failure analysis when an Autotest fails. CONTRAST 1. Select Contrast on the Preferences screen. Press ENTER. The Contrast screen appears. 2. Select / or / to adjust the screen contrast. Figure 2-4: Contrast Screen 3. Press ENTER to save or ESCAPE to exit. 2-3
- Page 2 and 3: LANTEK TM CABLE TESTER USER’S GUI
- Page 4 and 5: TABLE OF CONTENTS OPERATIONAL NOTES
- Page 6 and 7: TROUBLESHOOTING 10/100/1000 BASE-T
- Page 8 and 9: Headers and Footers Command .......
- Page 10 and 11: OPERATIONAL NOTES, CAUTIONS, AND WA
- Page 12 and 13: Chapter 1 Your Cable Tester PRODUCT
- Page 14 and 15: Chapter 1 Your Cable Tester Table 1
- Page 16 and 17: Chapter 1 Your Cable Tester Item DH
- Page 18 and 19: Chapter 1 Your Cable Tester HARD AN
- Page 20 and 21: Chapter 1 Your Cable Tester DISPLAY
- Page 22 and 23: Chapter 1 Your Cable Tester OVERVIE
- Page 26 and 27: Chapter 2 Test Setup Procedures TIM
- Page 28 and 29: Chapter 2 Test Setup Procedures Fig
- Page 30 and 31: Chapter 2 Test Setup Procedures PAC
- Page 32 and 33: Chapter 2 Test Setup Procedures TEM
- Page 34 and 35: Chapter 2 Test Setup Procedures Tab
- Page 36 and 37: Chapter 2 Test Setup Procedures Sav
- Page 38 and 39: Chapter 2 Test Setup Procedures OTH
- Page 40 and 41: Chapter 2 Test Setup Procedures Edi
- Page 42 and 43: Chapter 2 Test Setup Procedures ACT
- Page 44 and 45: Chapter 3 Structured Cable Field Ca
- Page 46 and 47: Chapter 3 Structured Cable Field Ca
- Page 48 and 49: Chapter 3 Structured Cable Field Ca
- Page 50 and 51: Chapter 3 Structured Cable Field Ca
- Page 52 and 53: Chapter 3 Structured Cable Field Ca
- Page 54 and 55: Chapter 3 Structured Cable Field Ca
- Page 56 and 57: Chapter 3 Structured Cable Field Ca
- Page 58 and 59: Chapter 3 Structured Cable Field Ca
- Page 60 and 61: Chapter 3 Structured Cable Field Ca
- Page 62 and 63: Chapter 3 Structured Cable Field Ca
- Page 64 and 65: Chapter 3 Structured Cable Field Ca
- Page 66 and 67: Chapter 3 Structured Cable Field Ca
- Page 68 and 69: Chapter 3 Structured Cable Field Ca
- Page 70 and 71: Chapter 3 Structured Cable Field Ca
- Page 72 and 73: Chapter 3 Structured Cable Field Ca
Chapter 2<br />
Test Setup Procedures<br />
AUTOTEST PREFERENCES<br />
Autotest can be set to automatically stop on the first failed test, as well as to save,<br />
and name test results at the completion of each test series.<br />
1. Select Autotest Preferences on the Preferences screen. Press ENTER. The Autotest<br />
Preference screen appears.<br />
2. Press the UP/DOWN ARROW keys to highlight the desired option.<br />
3. Press to activate or deactivate the highlighted option.<br />
Figure 2-3: Autotest Preference Screen<br />
4. Press ENTER to save or ESCAPE to exit.<br />
Table 2-1: Autotest Preference Options<br />
Option<br />
Simple Cable ID<br />
Stop on Fail<br />
AutoSave<br />
Save Graphs<br />
Auto Increment<br />
Confirm Delete<br />
Disable Fiber<br />
Autotest Length<br />
Enable 606A<br />
Dim Backlight<br />
Action<br />
Assign a fixed alpha value for the Cable ID.<br />
Autotest aborts at the first failed test. Otherwise, Autotest continues until all<br />
tests are completed, regardless of results.<br />
Note: If a wire map cannot be completed due to gross miss-wiring, the Autotest<br />
may abort regardless of the setting of this preference.<br />
Autotest automatically names and saves any passed AUTOTEST results. Failed<br />
tests are not automatically saved.<br />
Displaying graphs on the DH requires data to be transferred from the RH to the<br />
DH. To save time during testing, do not select this option.<br />
Note: De-selecting this option will not allow graphs to be loaded to the PC<br />
software or printed on certification reports.<br />
Autotest automatically increments Single and Double Cable ID test counters.<br />
Activate request to confirm any Delete operation.<br />
Disable or enable fiber Autotest length procedure.<br />
Enable 606-A Cable ID naming standard.<br />
Toggle illumination of screen display backlighting during Autotest.<br />
2-2