LANTEK User Manual - Ideal Industries

More documents

Recommendations

Info

Chapter 7 LANTEK REPORTER Software If you supply your own serial port cable, Figure 7-2 shows the wiring specifications. Figure 7-2: PC Uploading Cable Pinout ESTABLISHING A CONNECTION For USB Connection Figure 7-3: PC to Tester Connections 1. Attach the USB cable to the tester and an available USB port on the PC. 2. Turn on the tester. The tester has an Operating System and must complete booting up before actions can be taken. 3. After Booting is complete, press F2. Then select USB by pressing F3. 4. Designate an upload location. 5. From the LANTEK Reporter’s File Menu select Upload From Tester or select the Upload Test icon on the Toolbar to complete the Upload. A “Browse for folder” dialog appears. A new drive should appear as a “Removable Disk (E:) Double Click on the drive and a sub-folder should also appear. Click once on the “Stored Tests” folder to select it, then click the OK button. Note: Drive letter may vary depending on the number of drives installed on the user’s PC. 7-3
Chapter 7 LANTEK REPORTER Software For RS-232 Serial Connection 1. Attach the RS-232 cable to the tester and an available RS-232 port on the PC. 2. Turn on the tester. The tester has an Operating System and must complete booting up before actions can be taken. 3. Start the LANTEK Reporter program on the PC, go to the Options menu and select Upload Target. Then, select Comm Port. 4. Designate an upload location. 5. From LANTEK Reporter’s File Menu select Upload From Tester or select the Upload Test icon on the Toolbar to complete the Upload. For a serial port connection that is not responsive: 1. Go to the LANTEK Reporter Options menu and select the Tester ID command. The program will automatically scan the available communications ports and baud rates to locate and identify the attached Tester. If the tester is not identified, proceed to the next step. 2. Some PCs may have difficulties with this function and the following dialog box displays. Click OK. 3. Shut down any other applications that use the serial communication ports. 4. Click on the Options menu and select the Serial Port command. Select the correct Port and match the Baud Rate to that of your LANTEK tester. 5. After you have entered the values, click the Test button. If the Tester is identified, its serial and model numbers will be displayed. 6. Click OK. Note: If you have tried alternative baud rates and ports and LANTEK Reporter still cannot find the Tester, call IDEAL INDUSTRIES Customer Support. For Compact Flash Transfer 1. Insert the Flash card with the test results into the Flash Card Reader on the PC. 2. Start the LANTEK Reporter program on the PC, go to the Options menu and select Upload Target. Then select USB Compact Flash. 3. From LANTEK Reporter’s File Menu select Upload From Tester or select the Upload Test icon on the Toolbar to complete the upload. A “Browse for folder” should appear. A new drive should appear as a “Removable Disk (E:)” Double Click on the drive and a sub-folder should appear. Click once on the “Stored Tests” folder to select it. Then click the OK button. Note: Drive letter may vary depending on the number of drives installed on the user’s PC. 7-4
Page 2 and 3:
LANTEK TM CABLE TESTER USER’S GUI
Page 4 and 5:
TABLE OF CONTENTS OPERATIONAL NOTES
Page 6 and 7:
TROUBLESHOOTING 10/100/1000 BASE-T
Page 8 and 9:
Headers and Footers Command .......
Page 10 and 11:
OPERATIONAL NOTES, CAUTIONS, AND WA
Page 12 and 13:
Chapter 1 Your Cable Tester PRODUCT
Page 14 and 15:
Chapter 1 Your Cable Tester Table 1
Page 16 and 17:
Chapter 1 Your Cable Tester Item DH
Page 18 and 19:
Chapter 1 Your Cable Tester HARD AN
Page 20 and 21:
Chapter 1 Your Cable Tester DISPLAY
Page 22 and 23:
Chapter 1 Your Cable Tester OVERVIE
Page 24 and 25:
Chapter 2 Test Setup Procedures AUT
Page 26 and 27:
Chapter 2 Test Setup Procedures TIM
Page 28 and 29:
Chapter 2 Test Setup Procedures Fig
Page 30 and 31:
Chapter 2 Test Setup Procedures PAC
Page 32 and 33:
Chapter 2 Test Setup Procedures TEM
Page 34 and 35:
Chapter 2 Test Setup Procedures Tab
Page 36 and 37:
Chapter 2 Test Setup Procedures Sav
Page 38 and 39:
Chapter 2 Test Setup Procedures OTH
Page 40 and 41:
Chapter 2 Test Setup Procedures Edi
Page 42 and 43:
Chapter 2 Test Setup Procedures ACT
Page 44 and 45:
Chapter 3 Structured Cable Field Ca
Page 46 and 47:
Page 48 and 49:
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
Page 56 and 57:
Page 58 and 59:
Page 60 and 61:
Page 62 and 63:
Page 64 and 65: Chapter 3 Structured Cable Field Ca
Page 82 and 83: CHAPTER 4 COAX CABLE FIELD CALIBRAT
Page 84 and 85: Chapter 4 Coax Cable Field Calibrat
Page 86 and 87: CHAPTER 5 FIBER OPTICS CABLE FIELD
Page 88 and 89: Chapter 5 Fiber Optics Cable Field
Page 100 and 101: Chapter 6 Fiber Optics Diagnostics
Page 112 and 113: CHAPTER 7 LANTEK REPORTER SOFTWARE
Page 116 and 117: Chapter 7 LANTEK REPORTER Software
Page 140 and 141: APPENDIX A SAFETY PRECAUTIONS HANDL
Page 142 and 143: APPENDIX B CUSTOMER SUPPORT CUSTOME
Page 144 and 145: Appendix B Customer Support IDEAL I
Page 146 and 147: Appendix C Fiber Optic Cabling Stan
show all

LANTEK User Manual - Ideal Industries

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?