Heatlock ESB2, Electric Sprue Bushing

More documents

Recommendations

Info

Thermocouples This Heatlock series, below, is currently being replaced by the A1-series of nozzles. Before you design check availability, stock is gradually decreased. Spare parts will be available until at least end of 2007 (apart form NPT1 bodies) Thermocouples Themocouples for accurate measuring of temperature in moulds for injection moulding. All thermocouples are of J–Type and have grounded junctions. Lead wires are protected by a rugged stainless steel braided cover. Length of cables 900 mm. Connect: —Black (Red) to the positive pole (+) —White (Black)to the negative pole (–) Used between bandheaters and sprue bush or in applications where space will not permit any round type of thermocouple. Measures temperatures up to 400°C. The blade is made of copper and can be contoured to various shapes. Used to measure temperatures on i.e. manifolds. Measures the temperature in the tip of the tube. (400°C) Drill the hole for the thermocouple 1 mm shorter than the L–measurment to insure good contact at the measuring point. 13 32 B 5,5 1 13 Ø4 8 8 6 4 6 Part No. TC00240000 Part No. TC00040180 L 12 TC00040185 20 Thin thermocouple used to measure the temperature on our Heatlock bushes. The thermocouple is protected by a capton tube. It measures in the tip of the tube. The tube can be bent with an radius of min. 3mm. Measures temperatures up to 800°C. The 4 mm Ø-base can withstand temperatures up to max. 260°C. L 45 55 75 100 110 160 210 260 Part No. TC00140195 TC00140200 TC00140210 TC00140220 TC00140230 TC00140250 TC00140270 TC00140290 Ø1 "L" 40 Ø4 Date: 031002, © LKM Heatlock Co Ltd 2.50.5
This Heatlock series, below, is currently being replaced by the A1-series of nozzles. Before you design check availability, stock is gradually decreased. Spare parts will be available until at least end of 2007 (apart form NPT1 bodies) O-rings O-rings of stainless steel To seal the joints of hot runner systems. The O-ring is made of a stainless steel pipe and gives when built in according to the instructions a seal proof joint. A hole on the inside diameter of the tubular ring increases the internal pressure of the O-ring, when the plastic flow channel is filled with melted plastic material. This helps to increase the O-rings sealing capacity. Part No. I.Ø mm O.Ø mm ORING00500 9,56 12,70 ORING00608 11,10 14,27 ORING00610 14,27 17,45 ORING00615 15,90 19,05 ORING00620 17,45 20,65 ORING00630 19,05 22,23 ORING00640 23,80 26,97 ORING00645 25,43 28,58 ORING00650 26,97 30,18 Boring instructions for O-rings. 0,8 30° 1,19-1,27 0,38 R max C A +0.1 Part No. A -0.0 C ORING00500 12,83 8,89 ORING00608 14,40 10,46 ORING00610 17,59 13,65 ORING00615 19,18 15,24 ORING00620 20,76 16,83 ORING00630 22,35 18,42 ORING00640 27,15 23,16 ORING00645 28,70 24,76 ORING00650 30,29 26,35 2.50.6 Date: 031002, © LKM Heatlock Co Ltd
Page 2 and 3:
This Heatlock series, below, is cur
Page 4 and 5:
Page 6 and 7:
Page 8 and 9:
Page 10 and 11:
Page 12 and 13:
Page 14 and 15:
Page 16 and 17:
Page 18 and 19: This Heatlock series, below, is cur
Page 64 and 65: Cartridge Heaters This Heatlock ser
Page 66 and 67: Coilheater This Heatlock series, be
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
34.5 7.5 This Heatlock series, belo
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
DIGITAL CONTROLLERS This Heatlock s
Page 138 and 139:
DIGITAL CONTROLLERS This Heatlock s
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
8 7 This Heatlock series, below, is
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
Page 164 and 165:
Page 166 and 167:
Page 168 and 169:
Page 170 and 171:
Page 172 and 173:
Page 174 and 175:
Page 176 and 177:
Page 178 and 179:
Page 180 and 181:
Page 182 and 183:
Page 184 and 185:
Page 186 and 187:
show all

Heatlock ESB2, Electric Sprue Bushing

Create successful ePaper yourself

Delete template?

Save as template?