Heatlock ESB2, Electric Sprue Bushing

More documents

Recommendations

Info

This Heatlock series, below, is currently being replaced by the A1-series of nozzles. Before you design check availability, stock is gradually decreased. Spare parts will be available until at least end of 2007 (apart form NPT1 bodies) Heatlock PPB1, Mini PPB1 Features • Exceptionally uniform heat distribution along the bushing. • Direct gating with minimal restriction of the flow channel. • Plastic undergoes lowest possible thermal stress. • Compact. Egenskaper • Extremt jämn värmefördelning längs bussningen. • Direktintag–utan restriktion av flytkanalen • Minsta möjliga termiska påkänning på plasten. • Kompakt. 23 L=26-106 Ø30 Shot weights
R3 This Heatlock series, below, is currently being replaced by the A1-series of nozzles. Before you design check availability, stock is gradually decreased. Spare parts will be available until at least end of 2007 (apart form NPT1 bodies) PPB1 0.5 Ø4 Ø30 f8 Ø20 ”L” mm Single-cav. Part No. Multi-cav.* Total volume of feed channel in mm 3 26 PPB1026101 PPB1026102 560 23 +0.01 0 36 PPB1036101 PPB1036102 686 46 PPB1046101 PPB1046102 812 86 PPB1086101 PPB1086102 1314 L +0.1 -0.02 8 Ø20 10.8 106 PPB1106101 PPB1106102 1565 * with O-ring 500 / 608 Ø1.5 Can be controlled with various types of temperature controllers intended for hot runner systems with 220/240 V using thermocouple of type Fe-CuNi. 4 Ø8 h6 Recommended for the following maximum shot weights: Low-viscosity plastic (PS,PE,PP) 200g Med.-viscosity plastic (ABS,SAN, PA,POM) 100g High-viscosity plastic (PC,PMMA, Noryl, Filled material) 30g 15.5 Gate diameter is Ø0.8 mm on delivery, can be reamed up to Ø1.5 mm if needed. Please, look at page 9 regarding gate diameter. Length expansion at: °C=”L”+X,xx °C 26 36 46 86 106 Ø16 200 0,06 0,08 0,11 0,20 0,24 250 0,08 0,10 0,13 0,25 0,31 300 0,09 0,12 0,16 0,30 0,37 350 0,10 0,14 0,19 0,35 0,43 8 To ensure minimum vestige on the part, measure the actual "L" measurement on each bush, add the length expansion according to the table to get the hole depth ("L"+X,xx) to be drilled in the cavity plate. 23.5 R0.4 max Ø6 2.5 Före inbyggnad, mät upp bussningens nominella "L"-mått, lägg därefter till längdutvidgningen så att bussningens spets ligger exakt vid intagspunkten i uppvärmt tillstånd. 1.5 L 23 +0.01 -0 25° Ø24 Ø8 H7 Ø0.01 Ø30 H7 max 1.5 R3 0.2 Ø0.8 more 2.05.2 Date: 030930, © LKM Heatlock Co Ltd
Page 2 and 3: This Heatlock series, below, is cur
Page 64 and 65: Cartridge Heaters This Heatlock ser
Page 66 and 67: Coilheater This Heatlock series, be
Page 68 and 69: Thermocouples This Heatlock series,
Page 82 and 83:
This Heatlock series, below, is cur
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
34.5 7.5 This Heatlock series, belo
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
DIGITAL CONTROLLERS This Heatlock s
Page 138 and 139:
DIGITAL CONTROLLERS This Heatlock s
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
8 7 This Heatlock series, below, is
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
Page 164 and 165:
Page 166 and 167:
Page 168 and 169:
Page 170 and 171:
Page 172 and 173:
Page 174 and 175:
Page 176 and 177:
Page 178 and 179:
Page 180 and 181:
Page 182 and 183:
Page 184 and 185:
Page 186 and 187:
show all

Heatlock ESB2, Electric Sprue Bushing

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?